That's almost right. You cannot use a VGA cable with the Y-BOX or any Elecraft radio because they almost always short too many pins to ground.or to each other.
A straight 15 pin M/F (non-VGA) extension would have worked OK to extend the Elecraft ACC cable. I supply these with the Y-BOX. I can also obtain longer lengths. The Y-BOX transforms standard 15-pin straight cables (not VGA) to KPAK3AUX equivalent, plus some extras like powering on the amp. from a K3 or K4 macro, or optionally opening the keying line so that an external device like a SteppIR controller can protect itself from high power while it is moving. The "Key Line Interrupt" gender changer supplied with the KPAK3AUX cables is not needed with the Y-BOX since that's built into the Y-BOX as a jumper option. 73, Bob, N6TV https://bit.ly/Y-BOX On Sun, Sep 19, 2021 at 5:46 AM Eric Norris <norrislawfi...@gmail.com> wrote: > I must point out that N6TV's Serial and Y boxes can be configured to use > VGA cable between K2/K3/K4 and Elecraft amps. He does the hard work, and > his support is fantastic. > > 73 Eric WD6DBM > > On Fri, Sep 17, 2021, 7:23 AM Jack Brindle via Elecraft < > elecraft@mailman.qth.net> wrote: > >> VGA cables are incompatible with the KPA500 and KPA1500. You will need a >> straight-through cable. BUT, you also need some pins removed. The power pin >> of the K3 is not compatible with the power pin of the KPA500 or KPA1500, >> and will result in the problems you have seen. >> The cable is described in the KPA500 manual, rev E1 on page 45. I’m not >> sure where it is in the KPA1500 manual, but I would be surprised if we >> didn’t include the same table there. >> >> 73, >> Jack, W6FB >> Elecraft Engineering >> >> > On Sep 17, 2021, at 7:47 AM, Jim McCook <w...@cox.net> wrote: >> > >> > Now I see what's going on. Originally I used the Elecraft cable >> between the K3 ACC and the KPA1500 and everything was OK. The K3 could be >> powered down normally. When I moved that K3 to a spare position, that >> cable wasn't long enough, so I ordered an extension VGA cable. This is >> when the problem occurred. Apparently the extension is the problem withh >> pin 8. Will see what Elecraft Support says. 73, Jim W6YA >> > ______________________________________________________________ >> > Elecraft mailing list >> > Home: http://mailman.qth.net/mailman/listinfo/elecraft >> > Help: http://mailman.qth.net/mmfaq.htm >> > Post: mailto:Elecraft@mailman.qth.net >> > >> > This list hosted by: http://www.qsl.net >> > Please help support this email list: http://www.qsl.net/donate.html >> > Message delivered to jackbrin...@me.com >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to norrislawfi...@gmail.com > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com