When running sysinstall from the FreeBSD CD the debug screen is at Alt-F2. JN
On Tuesday 22 August 2006 12:02, Derek Ragona wrote: > The debug screen should not be blank, in addition to this error message you > will see all the output from the install up to that point. > > If this is a new install, I would blank the hard disk, and try a fresh > install. As the install is running check the debug screen periodically. > > -Derek > > At 10:57 AM 8/22/2006, unixforums 1 wrote: > >The debug screen is blank. > > > >To verify I had a good download I went to a different mirror site and > >downloaded the boot-only cd and had the same problems. > > > >Thron > > > >Derek Ragona <[EMAIL PROTECTED]> wrote: > >>What was on the debug screen? alt+F4 gets you to that screen. > >> > >>-Derek > >> > >>At 10:36 AM 8/22/2006, unixforums 1 wrote: > >> >I am having several problems loading 6.1 on a Dell PE 850 w/an Adaptec > >> >39160 scsi card and a single scsi drive. When I install from the boot > >> > only cd, I get the error "Unable to transfer the base distribution > >> > from acd0. Do you want to retry again" and it won't go any further. > >> > > >> >When I install using the 6.1 disk one I get the error "Add of package > >> >linux_base-8-8.01-14 aborted, error code 1 - Please check the debug > >> > screen for info" and when the system boots I the kernel will not load. > >> > This happens weather I install the linux compatible module or not. > >> > > >> >However I can install 6.0 without a problem and it seems to run like a > >> > >> champ. > >> > >> >Any ideas? > >> >Thron > >> > > >> > > >> > > >> > > >> >-----Original Message----- > >> >From: [EMAIL PROTECTED] > >> >[mailto:[EMAIL PROTECTED] On Behalf Of Josh Paetzel > >> >Sent: Monday, August 21, 2006 4:34 PM > >> >To: [EMAIL PROTECTED] > >> >Subject: FreeBSD on Dell PE850 > >> > > >> >Does anybody have any experience running FBSD 6.x on a PE850? I'm > >> >specifically wondering about support for their base-configuration > >> >onboard NIC and their CERC SATA RAID controller. > >> > > >> >-- > >> >Thanks, > >> > > >> >Josh Paetzel > >> > > >> > > >> > __________________________________________________ > >> >Do You Yahoo!? > >> >Tired of spam? Yahoo! Mail has the best spam protection around > >> >http://mail.yahoo.com > >> >_______________________________________________ > >> >freebsd-questions@freebsd.org mailing list > >> >http://lists.freebsd.org/mailman/listinfo/freebsd-questions > >> >To unsubscribe, send any mail to > >> > >> "[EMAIL PROTECTED]" > >> > >> >-- > >> >This message has been scanned for viruses and > >> >dangerous content by MailScanner, and is > >> >believed to be clean. > >> >MailScanner thanks transtec Computers for their support. > >> > >>-- > >>This message has been scanned for viruses and > >>dangerous content by MailScanner, and is > >>believed to be clean. > >>MailScanner thanks transtec Computers for their support. > >> > >>_______________________________________________ > >>freebsd-questions@freebsd.org mailing list > >>http://lists.freebsd.org/mailman/listinfo/freebsd-questions > >>To unsubscribe, send any mail to > >> "[EMAIL PROTECTED]" > > > >__________________________________________________ > >Do You Yahoo!? > >Tired of spam? Yahoo! Mail has the best spam protection around > >http://mail.yahoo.com > >-- > >This message has been scanned for viruses and > >dangerous content by <http://www.mailscanner.info/>MailScanner, and is > >believed to be clean. > >MailScanner thanks <http://www.transtec.co.uk/>transtec Computers for > >their support. _______________________________________________ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"