On Fri, Feb 14, 2014 at 11:23:55AM +0000, Lee Jones wrote:
> The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
> devices. It has 2 ports which it can use for either; both SATA, both
> PCIe or one of each in any configuration.
>
> Cc: devicet...@vger.kernel.org
> Cc: Srinivas Kandagatla <srinivas.kandaga...@st.com>
> Signed-off-by: Lee Jones <lee.jo...@linaro.org>
> ---
> arch/arm/boot/dts/stih416-b2020-revE.dts | 6 +++++-
> arch/arm/boot/dts/stih416-b2020.dts | 6 ++++++
> arch/arm/boot/dts/stih416.dtsi | 13 +++++++++++++
> 3 files changed, 24 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/stih416-b2020-revE.dts
> b/arch/arm/boot/dts/stih416-b2020-revE.dts
> index a874570..dbe67fa 100644
> --- a/arch/arm/boot/dts/stih416-b2020-revE.dts
> +++ b/arch/arm/boot/dts/stih416-b2020-revE.dts
> @@ -32,6 +32,10 @@
> ethernet1: ethernet@fef08000 {
> snps,reset-gpio = <&PIO0 7>;
> };
> - };
>
> + miphy365x_phy: miphy365x@0 {
This has registers at 0x0? Or is the unit-address wrong?
> + st,pcie_tx_pol_inv = <1>;
This is a boolean. The '= <1>' is not required and is confusing.
> + st,sata_gen = "gen3";
s/"gen3"/<3>/
Both these properties need s/_/-/ applied.
All these apply to the other dts too.
> + };
> + };
> };
> diff --git a/arch/arm/boot/dts/stih416-b2020.dts
> b/arch/arm/boot/dts/stih416-b2020.dts
> index 276f28d..fd9cbad 100644
> --- a/arch/arm/boot/dts/stih416-b2020.dts
> +++ b/arch/arm/boot/dts/stih416-b2020.dts
> @@ -13,4 +13,10 @@
> model = "STiH416 B2020";
> compatible = "st,stih416", "st,stih416-b2020";
This compatible list is the wrong way around. Left to right should go
from most specific to most general / oldest variant.
>
> + soc {
> + miphy365x_phy: miphy365x@0 {
> + st,pcie_tx_pol_inv = <1>;
> + st,sata_gen = "gen3";
> + };
> + };
> };
> diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi
> index 85b8063..9fd8efb 100644
> --- a/arch/arm/boot/dts/stih416.dtsi
> +++ b/arch/arm/boot/dts/stih416.dtsi
> @@ -9,6 +9,8 @@
> #include "stih41x.dtsi"
> #include "stih416-clock.dtsi"
> #include "stih416-pinctrl.dtsi"
> +
> +#include <dt-bindings/phy/phy-miphy365x.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/reset-controller/stih416-resets.h>
> / {
> @@ -140,5 +142,16 @@
> clocks = <&CLK_S_ICN_REG_0>;
> };
>
> + miphy365x_phy: miphy365x@0 {
The unit-address should be fe382000 rather than 0 to match the first reg
entry.
Cheers,
Mark.
> + compatible = "st,miphy365x-phy";
> + reg = <0xfe382000 0x100>,
> + <0xfe38a000 0x100>,
> + <0xfe394000 0x100>,
> + <0xfe804000 0x100>;
> + reg-names = "sata0", "sata1", "pcie0", "pcie1";
> +
> + #phy-cells = <2>;
> + st,syscfg = <&syscfg_rear>;
> + };
> };
> };
> --
> 1.8.3.2
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
