Clean up the ethernet gadget, using newer APIs and conventions:
- gadget_is_dualspeed() and gadget_is_otg() ... #ifdef removal
- Remove many now-needless #includes
- Use the VERBOSE_DEBUG convention
- Minor whitespace fixes.
- Fix a warning from "sparse".
Surprisingly, this saved about 2K of code (16%) on a fullspeed-only
ARMv4 platform. I'm bit puzzled by that (it's so much!), but approve
of the result.
Signed-off-by: David Brownell <[EMAIL PROTECTED]>
---
drivers/usb/gadget/ether.c | 147 +++++++++++++++++----------------------------
1 file changed, 57 insertions(+), 90 deletions(-)
--- g26.orig/drivers/usb/gadget/ether.c 2007-08-01 23:16:10.000000000 -0700
+++ g26/drivers/usb/gadget/ether.c 2007-08-01 23:18:16.000000000 -0700
@@ -19,41 +19,19 @@
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
+/* #define VERBOSE_DEBUG */
-// #define DEBUG 1
-// #define VERBOSE
-
-#include <linux/module.h>
#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/timer.h>
-#include <linux/list.h>
-#include <linux/interrupt.h>
#include <linux/utsname.h>
#include <linux/device.h>
-#include <linux/moduleparam.h>
#include <linux/ctype.h>
-
-#include <asm/byteorder.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-#include <asm/uaccess.h>
-#include <asm/unaligned.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
#include <linux/usb/ch9.h>
#include <linux/usb/cdc.h>
#include <linux/usb_gadget.h>
-#include <linux/random.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/ethtool.h>
-
#include "gadget_chips.h"
/*-------------------------------------------------------------------------*/
@@ -356,15 +334,15 @@ module_param (qmult, uint, S_IRUGO|S_IWU
#define qlen(gadget) \
(DEFAULT_QLEN*((gadget->speed == USB_SPEED_HIGH) ? qmult : 1))
-/* also defer IRQs on highspeed TX */
-#define TX_DELAY qmult
-
static inline int BITRATE(struct usb_gadget *g)
{
return (g->speed == USB_SPEED_HIGH) ? HS_BPS : FS_BPS;
}
#else /* full speed (low speed doesn't do bulk) */
+
+#define qmult 1
+
#define DEVSPEED USB_SPEED_FULL
#define qlen(gadget) DEFAULT_QLEN
@@ -390,7 +368,7 @@ static inline int BITRATE(struct usb_gad
do { } while (0)
#endif /* DEBUG */
-#ifdef VERBOSE
+#ifdef VERBOSE_DEBUG
#define VDEBUG DEBUG
#else
#define VDEBUG(dev,fmt,args...) \
@@ -830,8 +808,6 @@ static const struct usb_descriptor_heade
};
#endif
-#ifdef CONFIG_USB_GADGET_DUALSPEED
-
/*
* usb 2.0 devices need to expose both high speed and full speed
* descriptors, unless they only run at full speed.
@@ -934,18 +910,15 @@ static const struct usb_descriptor_heade
/* maxpacket and other transfer characteristics vary by speed. */
-#define ep_desc(g,hs,fs) (((g)->speed==USB_SPEED_HIGH)?(hs):(fs))
-
-#else
-
-/* if there's no high speed support, maxpacket doesn't change. */
-#define ep_desc(g,hs,fs) (((void)(g)), (fs))
-
-static inline void __init hs_subset_descriptors(void)
-{
+static inline struct usb_endpoint_descriptor *
+ep_desc(struct usb_gadget *g, struct usb_endpoint_descriptor *hs,
+ struct usb_endpoint_descriptor *fs)
+{
+ if (gadget_is_dualspeed(g) && g->speed == USB_SPEED_HIGH)
+ return hs;
+ return fs;
}
-#endif /* !CONFIG_USB_GADGET_DUALSPEED */
/*-------------------------------------------------------------------------*/
@@ -989,22 +962,19 @@ static struct usb_gadget_strings stringt
* complications: class descriptors, and an altsetting.
*/
static int
-config_buf (enum usb_device_speed speed,
- u8 *buf, u8 type,
- unsigned index, int is_otg)
+config_buf(struct usb_gadget *g, u8 *buf, u8 type, unsigned index, int is_otg)
{
int len;
const struct usb_config_descriptor *config;
const struct usb_descriptor_header **function;
-#ifdef CONFIG_USB_GADGET_DUALSPEED
- int hs = (speed == USB_SPEED_HIGH);
+ int hs = 0;
- if (type == USB_DT_OTHER_SPEED_CONFIG)
- hs = !hs;
+ if (gadget_is_dualspeed(g)) {
+ hs = (g->speed == USB_SPEED_HIGH);
+ if (type == USB_DT_OTHER_SPEED_CONFIG)
+ hs = !hs;
+ }
#define which_fn(t) (hs ? hs_ ## t ## _function : fs_ ## t ## _function)
-#else
-#define which_fn(t) (fs_ ## t ## _function)
-#endif
if (index >= device_desc.bNumConfigurations)
return -EINVAL;
@@ -1217,7 +1187,7 @@ eth_set_config (struct eth_dev *dev, uns
if (number)
eth_reset_config (dev);
usb_gadget_vbus_draw(dev->gadget,
- dev->gadget->is_otg ? 8 : 100);
+ gadget_is_otg(dev->gadget) ? 8 : 100);
} else {
char *speed;
unsigned power;
@@ -1399,24 +1369,22 @@ eth_setup (struct usb_gadget *gadget, co
value = min (wLength, (u16) sizeof device_desc);
memcpy (req->buf, &device_desc, value);
break;
-#ifdef CONFIG_USB_GADGET_DUALSPEED
case USB_DT_DEVICE_QUALIFIER:
- if (!gadget->is_dualspeed)
+ if (!gadget_is_dualspeed(gadget))
break;
value = min (wLength, (u16) sizeof dev_qualifier);
memcpy (req->buf, &dev_qualifier, value);
break;
case USB_DT_OTHER_SPEED_CONFIG:
- if (!gadget->is_dualspeed)
+ if (!gadget_is_dualspeed(gadget))
break;
// FALLTHROUGH
-#endif /* CONFIG_USB_GADGET_DUALSPEED */
case USB_DT_CONFIG:
- value = config_buf (gadget->speed, req->buf,
+ value = config_buf(gadget, req->buf,
wValue >> 8,
wValue & 0xff,
- gadget->is_otg);
+ gadget_is_otg(gadget));
if (value >= 0)
value = min (wLength, (u16) value);
break;
@@ -1585,12 +1553,12 @@ done_set_intf:
&& rndis_control_intf.bInterfaceNumber
== wIndex) {
u8 *buf;
+ u32 n;
/* return the result */
- buf = rndis_get_next_response (dev->rndis_config,
- &value);
+ buf = rndis_get_next_response(dev->rndis_config, &n);
if (buf) {
- memcpy (req->buf, buf, value);
+ memcpy(req->buf, buf, n);
req->complete = rndis_response_complete;
rndis_free_response(dev->rndis_config, buf);
}
@@ -2026,12 +1994,11 @@ static int eth_start_xmit (struct sk_buf
req->length = length;
-#ifdef CONFIG_USB_GADGET_DUALSPEED
/* throttle highspeed IRQ rate back slightly */
- req->no_interrupt = (dev->gadget->speed == USB_SPEED_HIGH)
- ? ((atomic_read (&dev->tx_qlen) % TX_DELAY) != 0)
- : 0;
-#endif
+ if (gadget_is_dualspeed(dev->gadget))
+ req->no_interrupt = (dev->gadget->speed == USB_SPEED_HIGH)
+ ? ((atomic_read(&dev->tx_qlen) % qmult) != 0)
+ : 0;
retval = usb_ep_queue (dev->in_ep, req, GFP_ATOMIC);
switch (retval) {
@@ -2188,8 +2155,7 @@ static int eth_stop (struct net_device *
}
if (rndis_active(dev)) {
- rndis_set_param_medium (dev->rndis_config,
- NDIS_MEDIUM_802_3, 0);
+ rndis_set_param_medium(dev->rndis_config, NDIS_MEDIUM_802_3, 0);
(void) rndis_signal_disconnect (dev->rndis_config);
}
@@ -2443,26 +2409,28 @@ autoconf_fail:
if (rndis)
device_desc.bNumConfigurations = 2;
-#ifdef CONFIG_USB_GADGET_DUALSPEED
- if (rndis)
- dev_qualifier.bNumConfigurations = 2;
- else if (!cdc)
- dev_qualifier.bDeviceClass = USB_CLASS_VENDOR_SPEC;
-
- /* assumes ep0 uses the same value for both speeds ... */
- dev_qualifier.bMaxPacketSize0 = device_desc.bMaxPacketSize0;
-
- /* and that all endpoints are dual-speed */
- hs_source_desc.bEndpointAddress = fs_source_desc.bEndpointAddress;
- hs_sink_desc.bEndpointAddress = fs_sink_desc.bEndpointAddress;
+ if (gadget_is_dualspeed(gadget)) {
+ if (rndis)
+ dev_qualifier.bNumConfigurations = 2;
+ else if (!cdc)
+ dev_qualifier.bDeviceClass = USB_CLASS_VENDOR_SPEC;
+
+ /* assumes ep0 uses the same value for both speeds ... */
+ dev_qualifier.bMaxPacketSize0 = device_desc.bMaxPacketSize0;
+
+ /* and that all endpoints are dual-speed */
+ hs_source_desc.bEndpointAddress =
+ fs_source_desc.bEndpointAddress;
+ hs_sink_desc.bEndpointAddress =
+ fs_sink_desc.bEndpointAddress;
#if defined(DEV_CONFIG_CDC) || defined(CONFIG_USB_ETH_RNDIS)
- if (status_ep)
- hs_status_desc.bEndpointAddress =
- fs_status_desc.bEndpointAddress;
+ if (status_ep)
+ hs_status_desc.bEndpointAddress =
+ fs_status_desc.bEndpointAddress;
#endif
-#endif /* DUALSPEED */
+ }
- if (gadget->is_otg) {
+ if (gadget_is_otg(gadget)) {
otg_descriptor.bmAttributes |= USB_OTG_HNP,
eth_config.bmAttributes |= USB_CONFIG_ATT_WAKEUP;
eth_config.bMaxPower = 4;
@@ -2599,12 +2567,11 @@ fail0:
if (rndis_set_param_dev (dev->rndis_config, dev->net,
&dev->stats, &dev->cdc_filter))
goto fail0;
- if (rndis_set_param_vendor (dev->rndis_config, vendorID,
- manufacturer))
+ if (rndis_set_param_vendor(dev->rndis_config, vendorID,
+ manufacturer))
goto fail0;
- if (rndis_set_param_medium (dev->rndis_config,
- NDIS_MEDIUM_802_3,
- 0))
+ if (rndis_set_param_medium(dev->rndis_config,
+ NDIS_MEDIUM_802_3, 0))
goto fail0;
INFO (dev, "RNDIS ready\n");
}
-------------------------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc.
Still grepping through log files to find problems? Stop.
Now Search log events and configuration files using AJAX and a browser.
Download your FREE copy of Splunk now >> http://get.splunk.com/
_______________________________________________
linux-usb-devel@lists.sourceforge.net
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
