Subject is wrong, this has nothing to do with ARM. Should be USB.
On Sat, 05 Jul 2014, Peter Griffin wrote:
> This patch documents the device tree documentation required for
> the ST usb3 controller glue layer found in STiH407 devices.
>
> Signed-off-by: Giuseppe Cavallaro <peppe.cavall...@st.com>
> Signed-off-by: Peter Griffin <peter.grif...@linaro.org>
> ---
> Documentation/devicetree/bindings/usb/dwc3-st.txt | 58
> +++++++++++++++++++++++
> 1 file changed, 58 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/dwc3-st.txt
>
> diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt
> b/Documentation/devicetree/bindings/usb/dwc3-st.txt
> new file mode 100644
> index 0000000..befd964
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt
> @@ -0,0 +1,58 @@
> +ST DWC3 glue logic
> +
> +This file documents the parameters for the dwc3-st driver.
Does this line really add anything to do the document, considering the
name and location of the file and the title above?
> +This driver provides the glue logic to use the dwc3 on STiH407 based
> platforms.
s/This driver/The DWC2 driver/
> +Required properties:
> + - compatible : must be "st,stih407-dwc3"
> + - reg : glue logic base address and USB syscfg ctrl register
> offset
> + - reg-names : should be "reg-glue" and "syscfg-reg"
Any reason why you have reg-* and *-reg? If you have to put 'reg' in
the name, it's usually appended, rather than prefixed.
> + - st,syscon : should be phandle to system configuration node which
> + encompasses the glue registers
> + - resets : phandle pointing to the system powerdown controller
> +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
> +See: Documentation/devicetree/bindings/reset/reset.txt
> +
> + - #address-cells, #size-cells : should be '1' if the device has sub-nodes
> + with 'reg' property
> +
> + - pinctl-names : A pinctrl state named "default" must be defined
> +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
> +
> + - pinctrl-0 : Pin control group
> +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
> +
> + - ranges : allows valid 1:1 translation between child's address space and
> + parent's address space
> +
> +Optional properties:
> + - st,dwc3-drd-device: to program the HC as "device" (static setup)
This will require a DT Ack.
> +Sub-nodes:
> +The dwc3 core should be added as subnode to ST DWC3 glue as shown in the
> +example below. The DT binding details of dwc3 can be found in:
> +Documentation/devicetree/bindings/usb/dwc3.txt
> +
> +Example:
> +
> +st_dwc3: dwc3@8f94000 {
> + status = "disabled";
Probably not good to disable the node in the example.
> + compatible = "st,stih407-dwc3";
> + reg = <0x08f94000 0x1000>, <0x110 0x4>;
> + reg-names = "reg-glue", "syscfg-reg";
> + st,syscfg = <&syscfg_core>;
> + resets = <&powerdown STIH407_USB3_POWERDOWN>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb3>;
> + ranges;
> +
> + dwc3: dwc3@9900000 {
> + compatible = "synopsys,dwc3";
> + reg = <0x09900000 0x100000>;
> + interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>;
> +
> + usb-phy = <&usb2_phy>, <&usb3_phy>;
> + };
> +};
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
