On Tue, May 16, 2006 at 08:23:33AM +1000, David Gwynne wrote:
> what driver is behind these sensor values?
>
> can you post a full dmesg and sysctl hw.sensors when everything is
> running ok?
>
See, that's the thing. I am not sure it is running OK, because I only appear
to get sensors.13 (FAN) messages (and entry in the sysctl table) when the
fan goes below 3000RPM (which is what I have set it to in sensorsd.conf).
The temperature appears to be OK, though.
Of course, someone is probably going to shoot me down for running 3.6 on
this box..
[EMAIL PROTECTED] sysctl -a |grep ^hw
hw.machine=i386
hw.model=Intel(R) Pentium(R) 4 CPU 3.00GHz ("GenuineIntel" 686-class)
hw.ncpu=1
hw.byteorder=1234
hw.physmem=1073258496
hw.usermem=1072328704
hw.pagesize=4096
hw.disknames=wd0,wd1
hw.diskcount=4
hw.sensors.0=lm0, VCORE_A, volts_dc, 1.54 V
hw.sensors.1=lm0, VCORE_B, volts_dc, 1.33 V
hw.sensors.2=lm0, +3.3V, volts_dc, 2.66 V
hw.sensors.3=lm0, +5V, volts_dc, 5.07 V
hw.sensors.4=lm0, +12V, volts_dc, 11.80 V
hw.sensors.5=lm0, -12V, volts_dc, -12.23 V
hw.sensors.6=lm0, -5V, volts_dc, -5.00 V
hw.sensors.7=lm0, +5VSB, volts_dc, 5.02 V
hw.sensors.8=lm0, VBAT, volts_dc, 3.23 V
hw.sensors.9=lm0, Temp1, temp, 26.00 degC / 78.80 degF
hw.sensors.10=lm0, Temp2, temp, 59.50 degC / 139.10 degF
hw.sensors.11=lm0, Temp3, temp, 27.50 degC / 81.50 degF
hw.cpuspeed=3000
hw.setperf=100
-bash-3.00$ cat /var/run/dmesg.boot
OpenBSD 3.6-stable (GENERIC) #0: Fri Jun 10 22:12:32 CEST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) 4 CPU 3.00GHz ("GenuineIntel" 686-class) 3 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,PNI,MWAIT,CNXT-ID
real mem = 1073258496 (1048104K)
avail mem = 972722176 (949924K)
using 4278 buffers containing 53764096 bytes (52504K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(e2) BIOS, date 08/03/04, BIOS32 rev. 0 @ 0xfbb30
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdf64
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfde90/208 (11 entries)
pcibios0: PCI Exclusive IRQs: 5 9 11 12
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801EB/ER LPC" rev 0x00)
pcibios0: PCI bus #2 is the last bus
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82865G/PE/P CPU-I/0-1" rev 0x02
ppb0 at pci0 dev 1 function 0 "Intel 82865G/PE/P CPU-AGP" rev 0x02
pci1 at ppb0 bus 1
uhci0 at pci0 dev 29 function 0 "Intel 82801EB/ER USB" rev 0x02: irq 5
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801EB/ER USB" rev 0x02: irq 12
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801EB/ER USB" rev 0x02: irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3 "Intel 82801EB/ER USB" rev 0x02: irq 5
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801EB/ER USB" rev 0x02: irq 9
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb1 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0xc2
pci2 at ppb1 bus 2
rl0 at pci2 dev 5 function 0 "Realtek 8139" rev 0x10: irq 11 address
00:04:61:73:2f:90
rlphy0 at rl0 phy 0: RTL internal phy
ichpcib0 at pci0 dev 31 function 0 "Intel 82801EB/ER LPC" rev 0x02
pciide0 at pci0 dev 31 function 1 "Intel 82801EB/ER IDE" rev 0x02: DMA, channel
0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <ST3160023A>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
wd1 at pciide0 channel 1 drive 1: <ST3160023A>
wd1: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd1(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 5
"Intel 82801EB/ER SMBus" rev 0x02 at pci0 dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5 "Intel 82801EB/ER AC97" rev 0x02: irq 12, ICH5
AC97
ac97: codec id 0x414c4760 (Avance Logic <60>)
audio0 at auich0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
lm0 at isa0 port 0x290/8: W83627HF
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask ff65 netmask ff65 ttymask ffe7
pctr: user-level cycle counter enabled
dkcsum: wd0 matched BIOS disk 80
dkcsum: warning: dup BSD->BIOS disk mapping
dkcsum: wd1 had no matching BIOS disk
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
WARNING: / was not properly unmounted
