Signed-off-by: Charles-Antoine Couret <charles-antoine.cou...@nexvision.fr>
---
drivers/net/phy/marvell.c | 111 +++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 109 insertions(+), 2 deletions(-)
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 13a93d8..e05209b 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -493,15 +493,122 @@ static int m88e1318_config_aneg(struct phy_device
*phydev)
return m88e1121_config_aneg(phydev);
}
+/**
+ * ethtool_adv_to_fiber_adv_t
+ * @ethadv: the ethtool advertisement settings
+ *
+ * A small helper function that translates ethtool advertisement
+ * settings to phy autonegotiation advertisements for the
+ * MII_ADV register for fiber link.
+ */
+static inline u32 ethtool_adv_to_fiber_adv_t(u32 ethadv)
+{
+ u32 result = 0;
+
+ if (ethadv & ADVERTISED_1000baseT_Half)
+ result |= ADVERTISE_FIBER_1000HALF;
+ if (ethadv & ADVERTISED_1000baseT_Full)
+ result |= ADVERTISE_FIBER_1000FULL;
+
+ if ((ethadv & ADVERTISE_PAUSE_ASYM) && (ethadv & ADVERTISE_PAUSE_CAP))
+ result |= LPA_PAUSE_ASYM_FIBER;
+ else if (ethadv & ADVERTISE_PAUSE_CAP)
+ result |= (ADVERTISE_PAUSE_FIBER
+ & (~ADVERTISE_PAUSE_ASYM_FIBER));
+
+ return result;
+}
+
+/**
+ * marvell_config_aneg_fiber - restart auto-negotiation or write BMCR
+ * @phydev: target phy_device struct
+ *
+ * Description: If auto-negotiation is enabled, we configure the
+ * advertising, and then restart auto-negotiation. If it is not
+ * enabled, then we write the BMCR. Adapted for fiber link in
+ * some Marvell's devices.
+ */
+static int marvell_config_aneg_fiber(struct phy_device *phydev)
+{
+ int changed = 0;
+ int err;
+ int adv, oldadv;
+ u32 advertise;
+
+ if (phydev->autoneg != AUTONEG_ENABLE)
+ return genphy_setup_forced(phydev);
+
+ /* Only allow advertising what this PHY supports */
+ phydev->advertising &= phydev->supported;
+ advertise = phydev->advertising;
+
+ /* Setup fiber advertisement */
+ adv = phy_read(phydev, MII_ADVERTISE);
+ if (adv < 0)
+ return adv;
+
+ oldadv = adv;
+ adv &= ~(ADVERTISE_FIBER_1000HALF | ADVERTISE_FIBER_1000FULL
+ | LPA_PAUSE_FIBER);
+ adv |= ethtool_adv_to_fiber_adv_t(advertise);
+
+ if (adv != oldadv) {
+ err = phy_write(phydev, MII_ADVERTISE, adv);
+ if (err < 0)
+ return err;
+
+ changed = 1;
+ }
+
+ if (changed == 0) {
+ /* Advertisement hasn't changed, but maybe aneg was never on to
+ * begin with? Or maybe phy was isolated?
+ */
+ int ctl = phy_read(phydev, MII_BMCR);
+
+ if (ctl < 0)
+ return ctl;
+
+ if (!(ctl & BMCR_ANENABLE) || (ctl & BMCR_ISOLATE))
+ changed = 1; /* do restart aneg */
+ }
+
+ /* Only restart aneg if we are advertising something different
+ * than we were before.
+ */
+ if (changed > 0)
+ changed = genphy_restart_aneg(phydev);
+
+ return changed;
+}
+
static int m88e1510_config_aneg(struct phy_device *phydev)
{
int err;
+ err = phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_M1111_COPPER);
+ if (err < 0)
+ goto error;
+
+ /* Configure the copper link first */
err = m88e1318_config_aneg(phydev);
if (err < 0)
- return err;
+ goto error;
- return 0;
+ /* Then the fiber link */
+ err = phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_M1111_FIBER);
+ if (err < 0)
+ goto error;
+
+ err = marvell_config_aneg_fiber(phydev);
+ if (err < 0)
+ goto error;
+
+ return phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_M1111_COPPER);
+
+error:
+ phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_M1111_COPPER);
+ return err;
}
static int marvell_config_init(struct phy_device *phydev)
--
2.7.4
