Hi, seems that the response from the scanner was not correctly passed back. Please have a look at http://www.kirchgessner.net/pub/sane/53c416.txt and check if you have configured your card in a similar way.
--Peter Johan van den Berg wrote: > Hi, > > I'm geeting the following error message while trying > to get scanimage -L to work with my HP 4P SCSI scanner > on Linux using the supplied SCSI interface card: > scl_inq: malformed response: expected '257d', got > '257E' > > Any ideas? > > My setup and output is as follows: > > root# sane-find-scanner > sane-find-scanner: found SCSI processor "HP C1130A > 3540" at device/dev/scanner > sane-find-scanner: found SCSI processor "HP C1130A > 3540" at device /dev/sg0 > sane-find-scanner: found SCSI processor "HP C1130A > 3540" at device /dev/sga > > root# scanimage -L > [sanei_debug] Setting debug level of hp to 128. > [hp] sane_init called > [hp] sane_init will finish with Success > [hp] sane_get_devices called > [hp] hp_read_config: hp backend v0.95 starts reading > config file > [hp] hp_read_config: processing line <scsi HP * * * * > * *> > [hp] hp_read_config: processing line </dev/sg0> > [hp] hp_read_config: attach scsi HP * * * * * * > [hp] hp_get_dev: New device /dev/sg0, connect-scsi, > scsi-request=1 > [hp] sanei_hp_device_new: /dev/sg0 > [hp] scsi_inquire: sending INQUIRE > [hp] scsi_new: sending TEST_UNIT_READY > [hp] scsi_flush: writing 2 bytes: > [hp] 0x0000 1B 45 > .E > [hp] scsi_flush: writing 7 bytes: > [hp] 0x0000 1B 2A 73 32 35 37 45 > .*s257E > [hp] scsi_read: 16 bytes: > [hp] 0x0000 1B 2A 73 32 35 37 45 00 48 50 20 20 20 > 20 20 20 .*s257E.HP > [hp] scl_inq: malformed response: expected '257d', got > '257E' > [hp] scl_errcheck: Can't read SCL error stack: Error > during device I/O > [hp] sanei_hp_device_new: SCL reset failed > [hp] scsi_close: closing fd 5 > [hp] hp_read_config: processing line <option > connect-device> > [hp] hp_read_config: attach /dev/sg0 > [hp] hp_get_dev: New device /dev/sg0, connect-device, > scsi-request=0 > [hp] sanei_hp_device_new: /dev/sg0 > [hp] scsi_flush: writing 2 bytes: > [hp] 0x0000 1B 45 > .E > [hp] hp_nonscsi_device_new: SCL reset failed > [hp] scsi_close: closing fd 4 > [hp] sane_get_devices will finish with Success > > No scanners were identified. If you were expecting > something different, > check that the scanner is plugged in, turned on and > detected by the > sane-find-scanner tool (if appropriate). Please read > the documentation > which came with this software (README, FAQ, manpages). > [hp] sane_exit called > [hp] sane_exit will finish > > root# cat /proc/scsi/scsi > Attached devices: > Host: scsi0 Channel: 00 Id: 01 Lun: 00 > Vendor: HP Model: C1130A Rev: 3540 > Type: Processor ANSI SCSI > revision: 02 > > root# cat /proc/scsi/sym53c416/0 > Symbios Logic 53c416 (rev. 0) at 0x220, irq 5, SCSI-ID > 7, fast pio > > I'm using a Mandrake 8.2 based system with 2.4.18-6mdk > kernel. > > Thx > Johan > > > __________________________________________________ > Do You Yahoo!? > HotJobs - Search Thousands of New Jobs > http://www.hotjobs.com > _______________________________________________ > Sane-devel mailing list > sane-de...@www.mostang.com > http://www.mostang.com/mailman/listinfo/sane-devel > >