[Elecraft] W2 Watt Meter firmware load?

to send commands to the W2 with my computer. Any help would be appreciated. Thank you, Glenn Maclean WA7SPY __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post

[Elecraft] KPA500 / KAT500 and W2 watt meter question

I just ordered the KPA500/KAT500 combo and W2 watt meter for my K3S. Should I use the key line interrupt connected to the W2 watt meter or should I connect the key line interrupt to the KAT500? Do I even need to use key line interrupt with the K line set up? Thanks in advance Glenn WA7SPY Sent

[Elecraft] K2100 and KAT100 FS

I have for sale a bare bones K2 100 S/N 6062 100 watts out on all bands, no options and a KAT100 all manuals included. This K2 has been carefully aligned and tested and works great! asking $800.00 for the K2100 and KAT100 or BO Reason for selling need to pay some bills. Glenn WA7SPY

[Elecraft] KPA100 no output above 11 watts

I just finished putting a KPA100 kit together. All the initial tests were satisfactory until I got to the point where it is time to check the output of the PA above 11 watts. When I set my K2 above 11 watts I get a High Current message with no power out. I set CAL current to 3.5 amps. I set

[Elecraft] Help with troubleshooting K2 receiver?

I have my K2 built to the second alignment step. It passed all the tests on the first part of the build on initial power up. My K2 is not hearing the 7. birdie. I am not hearing anything on 40 meters from receive signals with an outside antenna connected or my broad band generator

Re: [Elecraft] Help with troubleshooting K2 receiver?

I found my problem. I left C158 out some how. I now have signal and the 7. birdie.I am able to peak L1 and L2 without the slugs bottomed out in the cans. I do have a concern The highest I can get L30 to adjust to is 5.5 volts with the slug in L30 all the way to the bottom of the can. I am

[Elecraft] Need Help with K2 build

I recently purchased a new K2 to replace my older one that I sold a while ago. I am to the first power up test stage. Everything checks out normal except when I go to measure the 4.0 freq on the control board at the left side of C22. I get all 00s. I have checked the freq probe for

[Elecraft] OT Wullenweber Array

ask. Go here for the explanation - http://en.wikipedia.org/wiki/Wullenweber I wish I had room in my back yard for one of these and hook my K2 up to it! Glenn Maclean WA7SPY ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must

[Elecraft] FS Complete Elecraft K2 100 watt station reduced price

shaping mod. Rev A to Rev B current firmware. The K2 works perfectly full 100 watts out on all bands and has been tested and aligned by Gary at Elecraft. Glenn Maclean WA7SPY ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must

[Elecraft] Complete K2 station sold

The K2 station I had for sale has been sold. Thanks to all who inquired, Happy 4th of July! Glenn Maclean WA7SPY ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change

[Elecraft] FS K2100 built with extras

, and the Elecraft Heil desk Mike. The K2 works perfectly full 100 watts out on all bands and has been tested and aligned by Gary at Elecraft. I will consider throwing in the KAT100-1 100 watt automatic tuner. Glenn Maclean WA7SPY ___ Elecraft mailing list Post

[Elecraft] K2 fails first test

of the Elecraft products without a hitch. Any help would be appreciated. Thanks in advance, Glenn Maclean WA7SPY ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub

[Elecraft] Resolve to K2 failing first test

. The K2 now passed all initial tests. Never a dull moment! stupid stupid stupid! Thanks for your input Don Glenn Maclean WA7SPY Don Wilhelm wrote: Glenn, While it certainly does sound like your 7805 regulator has gone 'belly up' (you said it clicked relays at first and then stopped), I

Re: [Elecraft] KX1 #01221 Alive but shy of stated power?

through my old sent email messages. I purchased and built an early serial number KX1. I hope this help you. Glenn Maclean WA7SPY Sacramento, CA Here is what Gary at Elecraft had to say. I went by his guide lines. 33 ohms worked well in my case. Your milage may very. Yes it is OK to change R30 do

[Elecraft] SSB and M-2 microphone

I want to say the combination of doing the 2.4 Khz cap mod, and replacing the crystals on the RF board and SSB adapter( my ssb adapter board was one of the very first ones to come out)and receiving a MD2 microphone for Christmas is a winning combination. Having a Hakko 908 de-soldering tool made

Re: [Elecraft] Tuning indicator problem

Hi Don, Shorting pin 5 to 4 turns on the 10th LED. I guess my wiring to the front panel board is good. Glenn WA7SPY - Original Message - From: W3FPR - Don Wilhelm [EMAIL PROTECTED] To: Glenn Maclean [EMAIL PROTECTED]; elecraft@mailman.qth.net Sent: Monday, November 01, 2004 9:08 PM

[Elecraft] Need help trouble shooting a K1

Hi guys, I am helping a friend trouble shoot a K1 that he just finished putting together. This is a 2 band 40/20 meter K1. The 40 meter band is working perfect with a full 7 watts output into a 50 ohm dummy load. The power output can be adjusted up and down while in transmit on 40 meters. The 20