I have complete PX3-K as packaged by Elecraft for sale. Panadapter kit for the
KX3. Asking $560 ppd CONUS. Contact off list.
73, Mike AC5P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Anyone have an interest for subject cable UNUSED in original packaging?
Contact OFF list.
Mike AC5P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Your resting temperature at 42C seems TOO warm to me? My KPA resting temp
runs about the same as ambient temperature of shack, 25-30C. With 25-30W
drive from TS-890,my KPA seldom reaches 3rd stage 60 degrees. Have you
checked SWR or cable between 890 and KPA?
73, Mike AC5P
On
Am guessing that toroid transformer is 70% or more of total KPA mass?
Has anyone put it on a scale and remembed its weight?
Be sure to seat and torque bolt properly when putting it back in.
Mike AC5P
On Tuesday, November 22, 2022 at 07:50:22 AM CST, Michael Walker
wrote:
Not really.
Unused KXV3, (K3 Xverter I/O, RX Ant I/O) accessory kit with install
instructions FS for K3. $100ppd CONUS. Contact direct off list.
Mike AC5P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I was gifted a KPA-500 in Aug. 2019. Used about a month before It blew a main
line fuse. That was replaced and the amp remained dead. What happened was
the center bolt holding the power transformer was not torqued down properly and
when the amp was tilted the core shifted into the low
We were gifted a somewhat large (6"OD, 2.6" ID, 9/16" thick) ferrite core of
unknown mix and original use. On face was marked 6.6uH w/4turns. My
thinking it might make a good common mode RF choke on the output of an inverter
generator or on coax feedline. Not familiar with properties of
A short strip of friction tape under the feet works well also.
Mike AC5P
On Thursday, July 8, 2021, 03:07:37 PM CDT, Walter Underwood
wrote:
Yep, Museum Wax is the good stuff.
https://www.amazon.com/Quakehold-66111-Museum-Ounce-Clear/dp/B000FJU29U
The KPA-500 transformer should be more than just a "hair" away from sides
(step 6 above) as there are rubber bumpers and a ribbon cable between that
should NOT be pinched. Refer to Kit Assembly Instructions page 35 and figure
52.
Mike AC5P
On Sunday, May 30, 2021, 07:29:59 AM CDT, Eric
Have you tried a deflector tube on the internal speaker to direct the sound
toward your head/ears?
Mike AC5P
On Thursday, April 1, 2021, 01:18:45 PM CDT, Louis Visconti
wrote:
Can some one point me to a decent external speaker for my K2. Thanks.
Lou, KD2MU
--
This email has been
I inherited K3 s/n 7105 without original invoice and was curious to its birth
date? Anyone have a close serial with their order date?
Thanks,
Mike AC5P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Here is another idea. Search Te-Ne-Ke CW key at youtube.com Mike, AC5P
https://www.youtube.com/watch?v=2PZantLJRwc
On Monday, September 21, 2020, 10:46:55 AM CDT, Rich NE1EE
<73.de.ne...@gmail.com> wrote:
On 2020-09-19 10:27:-0400, Wilson Lamb wrote:
>
Does anyone know any engineers who are hams at NIST, Fort Collins, CO?I be
curious to know the RF loading coil and ground currents under the 0.024 wave
stub verticals for 5000M WWVB.
Mike AC5P
On Tuesday, September 1, 2020, 09:17:41 AM CDT, n6...@outlook.com
wrote:
Bill,
WWVB added
FWIW, my old K3 (Nov'08) only pulls 17.8Adc at 12.5V for 100W into 50ohm dummy
load at 14MHz.
Seems to follow your PA temp is gonna run hotter also. WHY such poor
efficiency Elecraft, (Wayne) ?
73,Mike, AC5P
On Friday, June 19, 2020, 12:03:45 PM CDT, Randy Farmer
wrote:
Mine
Stick some toothpicks in strip of styrofoam.
Mike AC5P
On Sunday, June 7, 2020, 11:14:11 AM CDT, k...@juno.com
wrote:
Contact the Audobon Society to see if you can have a nest for a bird of
prey (falcon perhaps). Hopefully, it is one that will like crows as
well...
73 de Ed
Don, Are those all 8 ft ground rods driven vertical in ground without help
from a rock drill? Lots of rock in your area? Mike AC5P
On Friday, June 5, 2020, 03:10:11 PM CDT, W2xj wrote:
To my mind, false economy.
Sent from my iPad
> On Jun 5, 2020, at 3:36 PM, Don Wilhelm
New unused AUX Cable set Optional KPA500 or KPA1500 to K3S/K3. Wont play with
my older K3 version with serial port. Asking $30 shipped CONUS only.
Mike AC5P
__
Elecraft mailing list
Home:
Anyone have link/s to INTERNAL photos of the KPA-1500PS? No find on google
image search.
73, Mike AC5P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Anyone else have their KPA-500 crash on power ON? All LED's briefly flash
then all dead. Main fuses good.
73, Mike AC5P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Anyone had experience packing a KX3 in an Apache 1800 waterproof case from
Harbor Freight? Saw the case today at HF and looked like it would fit okay
for good transport protection.
73, Mike AC5P
__
Elecraft mailing list
Home:
My kpa shows HV 76 both in standby AND operate. Drops to 61V, key down, 500W
output. AC line input drops from 124 to 122V at same time.
Mike AC5P
On Sunday, October 27, 2019, 03:19:39 PM CDT, Wes
wrote:
You are putting it into standby two places. Don't you mean "operate" for the
What is LENGTH of this cable?
Mike AC5P
On Thursday, October 10, 2019, 06:31:59 AM CDT, Dick Dievendorff
wrote:
See pages 15, 16, and 27 of the KPA500 Owner's manual for a description of
what the 15-pin ACC cable can do for you.
It amounts to band information both ways so the amp
Getting a nice boost from the stock speaker (MON level 2) at my preferred pitch
of 500Hz. Booster is a 12-3/4 inch piece of 1-1/4" PVC tube (1-5/8"OD) with
one end cut at 30 deg. Placed approx. 1/8 inch from the speaker holes gives the
best gain. Tube would be slightlyshorter for higher
Thanks Mike for the KPA-500 fan level settings. That answers the question I
was going to ask. Could find no fan level info in the owners manual or from
previous posts.I don't suppose any record kept of SPL readings at the
different levels? Anyone done that?
73, Mike AC5P
On
I recently inherited a KX3. I can see what CW pitch setting is (550), BUT not
been able to change it (to 500) with VFO A or B. "Set sidetone pitch" on page
16 of manual does not say how to CHANGE it? What's the trick?
73, Mike AC5P
Does anyone reading have a 1937,1938 or 1939 ARRL Radio Amateurs Handbook?
Please reply direct off list. Thanks
73 Mike AC5P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Could the Powerwerx SS-30DV be the same supply as the Tekpower TP-30SWI minus
the meter and a few dollars more? Anyone measure the efficiency of the
Powerwerx, AC input vs. DC output power?
73, Mike AC5P
On Wednesday, March 13, 2019, 09:03:41 PM CDT, Dennis Moore
wrote:
I have the
Anyone on list using a Tekpower TP30SW1 switching power supply? It is model
with Anderson power poles on front panel.Please reply direct. Thanks
73, Mike AC5P
__
Elecraft mailing list
Home:
I get the best response for CW pitch volume from the K3 stock speaker with my
60 degree deflector horn on top. The length was determined by experiment and
gives a very noticeable boost at my desired pitch of 500Hz.
Mike AC5P
On Saturday, September 22, 2018 8:38 AM, Dave Cole (NK7Z)
Dual 35kW ERP synchronous transmitters and antennas for 70kW ERP at 60kHz.
Short (for 5km wavelength!) 4x400 ft quad towers that support top hat. Center
connected cable is main radiator. Hard to see getting 35kW ERP out of 100kW
transmitter at 5000 meter wavelength for such a short stub
Okay have looked over the posts, but somehow have missed the actual
AWG(American wire gage) SIZE of the stock DC pair? Anyone KNOW this or maybe
even micro-ohm tested (a long shot) it? Voltage drop (ps to amp) divided by
full load dc amps would be close enough.
73,
Mike AC5P
On
Thanks to the many of you who replied. Got wanted info pretty quickly.
Amazing how many are holding on to old RA handbooks.
73,
Mike AC5P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Would anyone reading per chance have a 1960 or '61, '62 Radio Amateurs Handbook
handy?Reply direct off list. Thanks
Mike AC5P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Interesting readings. Would have thought KXPA more efficient. Is this into
dummy load and what frequency was test?
73, Mike AC5P
On Monday, March 12, 2018 7:57 AM, Jan wrote:
Power readings here in Ypsilanti . . .Using the KX3/PX3/KXPA100 for
several years now AND
A line voltage monitor/alarm a very good idea. Am surprised Dave's KPA500
power transformer core was not humming away at 60hz over excitation before he
got it off line?Being retired from a large electric utility substation
department, I know LTC (load tap changer) controls can sometimes
Oh my! The KPA500 is more efficient than you give it credit. Since few have
instruments to measure ac input parameters, will volunteer actual measurement
figures.At 650W output into 50 ohm load, highest VA recorded was at 14.1 MHz at
1166. Watts 974 with a pf of 0.83 or 83%. AC input amps
Curious if anyone used 2000W inverter type generator for portable FD
operation? What brand machine and what experience with RF noise
encountered?Did anyone use Champion or Predator brand inverter generators?
Reply direct is fine.Mike AC5P
37 matches
Mail list logo