Ordered K4D w/KAT4 4/4/23; PIA. Quoted shipment 15 – 20 WORKING days ….
Patiently QRX .,,,
de Ben W4SC
Sent from Mail for Windows
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I'm fairly sure that (forward power) - (reverse power) gives the correct
nett output power, before cable and antenna losses. I'd need to review
the maths to be sure. Most reflected power ends up re-re-reflected, as
additional forward power. A high SWR will giver reflected power almost
as
Hi Keith,
Thanks for the reply. I tried a bunch of different width/mode
assignments just now, but got a strange rumbling noise with those
configurations. Thanks for suggesting taking a picture of the original
config, because my experimental settings got pretty wild!
73
Dave Hachadorian,
Eric,
now that it looks the K4-F is finally on a production schedule, any
hints on when there will be a K4-K ??
Thanks,
Neil, KN3ILZ
On 4/13/2023 3:18 PM, Eric Swartz wrote:
Hi Rick,
It looks like your K4D shipped today. :-)
We're also working hard to ship a lot this week and next so we
Try using the K3 Utility to re-label the .250 to a different value, like
6K, make sure it has a checkmark for AM.
Or try disabling the other slots by maybe just unchecking any that have
AM checkboxes.
Experiment with that, you should be able to have it stay on the .250 and
still be able to use
For an upcoming Frequency Measurement Test, I'm trying to use a K3 in
AM Mode RX-only with a 250 Hz CW Filter. My plan for the FMT is to use a
GPS Disciplined Oscillator as a BFO, and by measuring the frequency of
the beat tone, I will be able to accurately determine the mystery
transmit
Looking For KIO2 RS-232 Aux-IO Board With Interface Cable (The Kit). Thank
You, 73’s.
Ray WD4X
239-227-9414
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
I received the KIO3BUPKT_KIO3B, too.
I vacillated on ordering this upgrade at first as the original KIO3B was
working fine with my hardware RS-232 interface in the shack computer. The
embedded sound card wasn't of much interest as digital modes are not of
much interest either. I may keep the
Bob,
I might agree with you, EXCEPT I was using the setup with the P3 2KW
sensor between the KAT500 and the antenna for several months or more,
before the P3 crapped out on me. And during that time, I didn't notice
any unusual power readings. This may be because the sensor outputs 4
I also received my KSYNAUPGD_KSYN3A board kit and my KIO3BUPKT_KIO3B board
kit.
I still have a KXV3 upgrade kit on order.
Rich
NU6T
On Fri, Apr 14, 2023 at 7:35 AM Steve Zabarnick wrote:
> After just about two years from my original order, I finally received the
> upgraded K3 synthesis board
FS: KPA500 and KAT500 – combo Downsized and excess to needs. Purchased new,
factory build, non-smoking environment. Low hours, excellent working and
physical condition. Includes DB15 M/F cable, IEC 120V U.S. power cable, E850463
KAT500 to KPA500 cable, E980190 DB15 Y cable and original
After just about two years from my original order, I finally received the
upgraded K3 synthesis board (KSYN3AUPGD). Installation will take place this
weekend and I'm hoping for the best.
Steve N9SZ
On Thu, Feb 2, 2023 at 9:47 AM Steve Zabarnick wrote:
> It has been over 8 weeks since Eric
Also, if you ordered a K4HD and not a K4D you are still waiting.
This happened to me until I changed my order to a K4D and said I would take the
HD upgrade board when it came out.
I got my K4D in 3 or 4 weeks. This was last May.
73,
Mark, WB9CIF
K4 #743
-Original Message-
From:
FS: P3 Panadapter with Transmit Monitor (TX MON) Option (no SVGA) Downsizing
and excess to needs. Purchased new, factory built, non-smoking environment.
Excellent physical and working condition. Shipped in factory box with original
cables and instruction manual. CONUS only. $725 plus
> So what's the guy talking about putting money up 2 years ago and still
not receiving his radio?
I couldn't figure it out, as I ordered a K4D in February with no deposit,
and received it in just 7 weeks.
It occurred to me he might be talking about putting money down for a K3
board, not a K4
The initial wait when the K4 was first announced (in Dayton?) might have been
that long but that was a few years ago. The reports you are seeing now are
present day reality. Elecraft publishes shipping status on their website for
all of their products. https://elecraft.com/pages/shipping-status
So what's the guy talking about putting money up 2 years ago and still not
receiving his radio?
My offer is still good
73
Dean K2WW
On Thu, Apr 13, 2023, 9:01 PM wrote:
> Mine was ordered in February 11 and received it April 7.
> Believe me the wait is well worth it.
>
> 73,
> Brian K1DIH
>
>
17 matches
Mail list logo