[Paraview] PV4.1.0 multiple rulers

I have a slice plane with 2 cylinders separated. I use rule to measure the length of the re-circulation zone after each cylinder. Independently, the ruler shows the distance. When I save the jpg I would like to see both distances on the figure. At the moment I can only see one not both. Is

Re: [Paraview] PV4.10 extracting a surface

Forgot to mention that the mesh is 3D x,y,z. rad =sqrt( x**2+y**2) thus varies with the z-coordinate. Stephen - Original Message - > From: "Stephen Wornom" <stephen.wor...@inria.fr> > To: "ParaView" <paraview@paraview.org> > Sent: Wednesda

[Paraview] PV4.10 extracting a surface

The geometry is a cylinder. Using the calculator I do rad =sqrt( x**2+y**2) I would like to extract the cylinder surface which is rad = 0.1 I click on threshold then information to see rad 0.1

Re: [Paraview] wallShearStress Calculation in Paraview

Thanks, but did you forget to include the name of the forum? Stephen - Original Message - > From: "Ezhilmathi Krishnasamy" > To: "Ahmet Ahmet" > Cc: "ParaView" > Sent: Wednesday, December 6, 2017 3:05:56 PM >

Re: [Paraview] post-process of CFL3D result with surfaces in paraview?

I have a different code but had the same problem that I resolved by adding an additional variable which sets value 0 at interior points and a different values for each surface, for example, -3 for the wing surface points. Then I use "extract" to visualize the different surfaces. Hope this

Re: [Paraview] PV 4.10 how to locate x, y, z for negative pressure at a point

Westphal" <mathieu.westp...@kitware.com> > To: "Stephen Wornom" <stephen.wor...@inria.fr> > Cc: "ParaView list" <paraview@paraview.org>, "Emmanuelle" > <emmanuelle.i...@univ-montp2.fr> > Sent: Wednesday, September 14, 2016 2:26:56 P

[Paraview] PV 4.10 how to locate x, y, z for negative pressure at a point

PV information shows a negative pressure, how can I locate the coordinates where the negative pressure occurs? I hope my question is clear. Thanks, Stephen ___ Powered by www.kitware.com Visit other Kitware open-source projects at

Re: [Paraview] PV 4.1 how to extract a surface

er give what you are looking to obtain? The result of the Extract Surface filter can also be trimmed visa the Clip filter. Sam On 6/27/2016 2:14 AM, Stephen Wornom wrote: The mesh is 3D unstructured about a 3D cylinder. I would like to extract the surface of the cylinder. I have experience ext

[Paraview] PV 4.1 how to extract a surface

The mesh is 3D unstructured about a 3D cylinder. I would like to extract the surface of the cylinder. I have experience extracting surfaces with another code where the surfaces are defined by a variable (-3= cylinder surface). I do it like this: 1-select extract surface 2-select

Re: [Paraview] PV 4.1 animating plot over line using global max/min

- Original Message - > From: "Kenneth Moreland" <kmo...@sandia.gov> > To: "Stephen Wornom" <stephen.wor...@inria.fr>, "ParaView list" > <paraview@paraview.org> > Sent: Thursday, September 3, 2015 6:35:42 PM > Subject: Re:

[Paraview] PV 4.1 animating plot over line using global max/min

Is there an option so that animating plot over line will use the global max/min values instead of the localo max/min values for each time step? animating contours uses the global max/min values and I would like to do this with plot over line. Hope my question is clear. Stephen

[Paraview] PV 4.1.0 how to plot over line for two different time step on same figure

Plot ove line creates a figure. Is it possible to impose two different time steps on the same figure? Hope my question is clear. Thanks, Stephen ___ Powered by www.kitware.com Visit other Kitware open-source projects at

[Paraview] PV 4.10 plot over line using mesh coordinates

One of the inputs to Plot over line is the number of points (equally spaced, I assumed). The solution is interpolated to the points. This poses a problem for highly stretched meshes like the normal coordinate in a boundary layer. I would like to plot over line using the actual mesh values and

Re: [Paraview] FlyIn and FlyOut in ParaView 4

Utkarsh Ayachit wrote: Thomas, Alas no. That was something that was lost in 3.0 transition. I haven't looked into it in detail, but if there's sufficient interest, it should not be too hard to resurrect the old code. Yes it would be very useful. Thanks, Stephen Utkarsh On Fri, May 22, 2015

[Paraview] PV 4.1.0 programmimg the camera position using python

Are there some examples available showing how to programming the camera position using python? The position would be a function (x,y,z,t). Hope my question is clear. Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel: 04 92 38 50

Re: [Paraview] PV 4.01 How to reduce the size of the slice plane

as well. Just specify the extent accordingly. Utkarsh On Tue, Apr 14, 2015 at 8:28 AM, Stephen Wornom stephen.wor...@inria.fr wrote: Say I select an x-slice. The slice plane is a rectangular dimensions 100x100. Has does one slice a subset of 10x10? Hope my question is clear, Stephen

Re: [Paraview] PV 4.01 How to reduce the size of the slice plane

Stephen Wornom wrote: Utkarsh Ayachit wrote: Try applying Extract Subset filter to extract a slab of interest first, and then slice it. I am using PV4.01 linux 64-bit binary version parallel version for the client downloaded from the paraview site. On the server, PV4.01 was created

[Paraview] PV 4.01 How to reduce the size of the slice plane

Say I select an x-slice. The slice plane is a rectangular dimensions 100x100. Has does one slice a subset of 10x10? Hope my question is clear, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel: 04 92 38 50 54 Fax: 04 97 15 53 51

Re: [Paraview] PV 4.1.0: save the data saves only 1/2 of a circle PROBLEM SOLVED - SAVE the csv file using the SCIENTIFIC NOTATION

Recall that I have two cylinders. 1- extract a surface 2- connectivity 3- threshold 4 slice in the z-coordinate This produces two circles in the x-y plane. 5- I save the data in a csv file using the default format. 6- To read the cvs file in fortran, I replace the commas by a blank. 7- I read

Re: [Paraview] PV 4.1.0: save the data saves only 1/2 of a circle

to see if this is the problem?). Thanks for your help, Stephen - Original Message - From: Kenneth Moreland kmo...@sandia.gov To: Stephen Wornom stephen.wor...@inria.fr, ParaView list paraview@paraview.org Sent: Monday, March 9, 2015 6:28:45 PM Subject: Re: [Paraview] PV 4.1.0: save

Re: [Paraview] PV 4.1.0: save the data saves only 1/2 of a circle

- Original Message - From: Kenneth Moreland kmo...@sandia.gov To: Stephen Wornom stephen.wor...@inria.fr Cc: ParaView list paraview@paraview.org Sent: Wednesday, March 11, 2015 4:55:06 PM Subject: Re: [Paraview] PV 4.1.0: save the data saves only 1/2 of a circle Stephen, I

Re: [Paraview] PV 4.1.0: save the data saves only 1/2 of a circle

. Stephen On 3/10/15, 11:01 AM, Stephen Wornom stephen.wor...@inria.fr wrote: I tried both PV 4.10 and PV 4.31 and get the same result. - extract surface - connectivity - threshold (defines the surface of the cylinder) information shows ymax= 0.5, ymin=-0.5 which is correct as the radius

[Paraview] PV 4.1.0: save the data saves only 1/2 of a circle

I have a cylinder ( a circle in the x-y plane, z is the span direction). I do: - extract surface - connectivity - threshold (defines the surface of the cylinder) The result is the circle shown in that attached figure. I want to write the circle values to a file so I save the data. The problem

Re: [Paraview] PV4.1: How to see the 9 scalar components of the gradient of velocity

Stephen Regards, Andy On Tue, Mar 3, 2015 at 9:19 AM, Stephen Wornom stephen.wor...@inria.fr wrote: I compute the vector gradients. There are 9 components of the matrix. Whe

[Paraview] PV4.1: How to see the 9 scalar components of the gradient of velocity

I compute the vector gradients. There are 9 components of the matrix. When I select the calculator, the 9 scalar components are not found. How can I get the 9 scalar components into the calculator? Hope my question is clear, Thanks, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles -

Re: [Paraview] Save 2 views as animations/images in same layout

Madalena S. Malhadas wrote: Dear all, I have a script that animate two views in same layout. The Scritp run fine, but apears to have a problem saving one single image formed by the 2 views. I made a

[Paraview] PV4.1: plot over line using actual points rather than interpolated points

Plot over a line requests the number of points. I would like to use the actual mesh points, is this possible? Hope the question is clear, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel: 04 92 38 50 54 Fax: 04 97 15 53 51

[Paraview] PV 4.1: animations of large data

I create animation using PV with mpi. I can create 200 frames quickly, no problem. The problem is visualizing the frames. What I do currently is to create a gif convert *.jpg animation.gif animate animation.gif The problem is that the gif file is huge, takes a long time to load the gif

Re: [Paraview] [clusters-sophia.users] PV 4.1: animations of large data

On 01/07/2015 02:48 PM, Nicolas Niclausse wrote: Stephen Wornom a écrit le 07/01/2015 10:47 : I create animation using PV with mpi. I can create 200 frames quickly, no problem. The problem is visualizing the frames. What I do currently is to create a gif convert *.jpg animation.gif animate

Re: [Paraview] [clusters-sophia.users] PV 4.1: animations of large data

On 01/07/2015 04:54 PM, Stephen Wornom wrote: On 01/07/2015 02:48 PM, Nicolas Niclausse wrote: Stephen Wornom a écrit le 07/01/2015 10:47 : I create animation using PV with mpi. I can create 200 frames quickly, no problem. The problem is visualizing the frames. What I do currently

[Paraview] PV-4.1 plot over line, how to use symbols

How does one use symbols rather than solid line? Thanks, Stephen -- # Tandem cylinders pressure waves http://www-sop.inria.fr/members/Stephen.Wornom/animate_tandem_cylinders_sound_waves.html # pressure wave explosion when vortex shedding begins (be patient, startup is slow)

Re: [Paraview] Paraview for time series of images

On 11/09/2014 11:07 PM, Agustin Lobo wrote: Hi! I'm looking into Paraview for the analysis of time series of satellite images. I've followed the tutorial and now wonder how to open a set of sequential tif (actually geotif) images. Would (in linux) convert *.tif image.gif animate image be of

[Paraview] PV 4.1 How to extract a slice for z= constant

The mesh is unstructured, PV running mpi. The mesh is rectangular. I would like to extract an exterior boundary. How does one do this? Thanks, Stephen ___ Powered by www.kitware.com Visit other Kitware open-source projects at

[Paraview] PV 4.1.0 plot over line question

My mesh is unstructured. I want the values along line in the x-direction. The line crosses two cylinders. PV proposes 100 values. When I edit the .csv file that is created when I save data, I find 5 lines with nan. They are near where the cylinders break the line. Any ideas as to not get the

Re: [Paraview] Make animation from steady state result

Thanks for passing this on. I am using PV 4.1.0, maybe it was written for an earlier version of PV. I did step 2, but step 2a ( Change the Contour By property to IntegrationTime), I do not see this option. I downloaded the PV 4.1.0 binaries, could that be the problem? Stephen On

[Paraview] PV-4.1 programming the camera position in time x(t), y(t), z(t)

When I open my PV .pvtu file the object is not visible. I must change the camera position (zoom) to bring the object in the fore ground. Is it possible to program the camera position as a function of time? Thanks, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia

[Paraview] PV 4.1.0 binary download ; unstructured mesh. reading pieces fails

I have 64 vtu pieces listed in my data.pvtu file. I do not wish to visualize pieces 36, 48, and 49. I remove them from the data.pvtu file (61 vtu pices remain). When I open the data.pvtu file I get this error. ERROR: In

Re: [Paraview] PV 4.1.0 binary download ; unstructured mesh. reading pieces fails

Utkarsh Ayachit wrote: Can you attach the original and modified pvtu file? That'll make it easier :). The solf_2D.004000.before.pvtu contains the 1st 40 the vtu files. When I open it in PV, I get an error that PV cannot read piece 36. solf_2D.004000.after.pvtu does not contain piece 35. I

Re: [Paraview] PV 4.1.0 binary download ; unstructured mesh. reading pieces fails

that the problem was simply due to a bad mesh. PV 4.1.0 works correctly. Thanks, Stephen Utkarsh On Wed, May 7, 2014 at 9:34 AM, Stephen Wornom stephen.wor...@inria.fr wrote: Utkarsh Ayachit wrote: Can you attach the original and modified pvtu file? That'll make it easier :). The solf_2D

Re: [Paraview] Need advice with parallel file format

Mohammad Mirzadeh wrote: Hi I am at a critical point in deciding I/O format for my application. So far my conclusion is to use parallel HDF5 for restart files as they are quite flexible and portable across systems. When it comes to visualization, however, i'm not quite sure. Up until now

[Paraview] PV 4.1.0 computing 3D lift and drag coefficients wing-body-nacelle combination

I do: - select extract surface - select connectivity - threshhold (to say what surface) I now have the surface of the wing and nacelle visible. To compute the lift and drag, I need to generate surface normals. But this filter is not active. How do I generate surface normals? Thanks, Stephen

Re: [Paraview] PV 4.1.0 ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary file

: AMD Athlon(tm) II X2 215 Processor Is this processor consistent with 64-bits (after I install the 64 bit version of Ubuntu)? Stephen Regards, Paul On 19 March 2014 20:50, Stephen Wornom stephen.wor...@inria.fr mailto:stephen.wor...@inria.fr wrote: uname -m | sed 's/x86_//;s/i[3-6]86

Re: [Paraview] PV 4.1.0 ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary file

the other way around. Regards, Paul On 18 March 2014 20:06, Stephen Wornom stephen.wor...@inria.fr wrote: uname -a Linux stephen-VG269AA-ABF-p6205fr 3.2.0-60-generic-pae #91-Ubuntu SMP Wed Feb 19 04:14:56 UTC 2014 i686 athlon i386 GNU/Linux home:ldd /home

Re: [Paraview] PV 4.1.0 ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary file

uname -m | sed 's/x86_//;s/i[3-6]86/32/' 32 problem resolved. Stephen - Original Message - From: Stephen Wornom stephen.wor...@inria.fr To: Patrik Blahuta patrik.blah...@gmail.com Cc: paraview@paraview.org Sent: Wednesday, March 19, 2014 9:31:58 PM Subject: Re: [Paraview] PV

Re: [Paraview] PV 4.1.0 ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary file

-gate.so.1 = (0xb7784000) libc.so.6 = /lib/i386-linux-gnu/libc.so.6 (0xb75c) /lib/ld-linux.so.2 (0xb7785000) ununtu 12.04 Hope this helps, Stephen - Original Message - From: Paul Edwards paul.m.edwa...@gmail.com To: Stephen Wornom stephen.wor...@inria.fr Cc: ben boeckel ben.boec

Re: [Paraview] PV 4.1.0 ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary file

Ben Boeckel wrote: On Sun, Mar 09, 2014 at 12:20:45 +0100, Stephen Wornom wrote: From: Ben Boeckel ben.boec...@kitware.com Is the filesystem mounted noexec? Not to my knowledge, how would I check? The output of 'mount' will show the flags for mounted filesystems. I downloaded the 32-bit

Re: [Paraview] PV 4.1.0 ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary file

- Original Message - From: Ben Boeckel ben.boec...@kitware.com To: Stephen Wornom stephen.wor...@inria.fr Cc: ParaView list paraview@paraview.org Sent: Sunday, March 9, 2014 3:13:37 AM Subject: Re: [Paraview] PV 4.1.0 ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary

Re: [Paraview] PV 4.1.0 ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary file

- Original Message - From: Paul Edwards paul.m.edwa...@gmail.com To: Stephen Wornom stephen.wor...@inria.fr Cc: ParaView list paraview@paraview.org Sent: Sunday, March 9, 2014 12:21:42 PM Subject: Re: [Paraview] PV 4.1.0 ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary

[Paraview] PV 4.1.0 ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary file

I have ubuntu as the operating system ParaView-4.1.0-Linux-64bit/bin/paraview: cannot execute binary file ls -al /home/stephen/ParaView-4.1.0-Linux-64bit/bin/paraview -rwxr-xr-x 1 stephen stephen 79439 Jan 13 06:48 /home/stephen/ParaView-4.1.0-Linux-64bit/bin/paraview home:file

Re: [Paraview] [EXTERNAL] Paraview compiled version - MPI

Scott, W Alan wrote: Leo, Make sure you aren’t running out of memory. /View/ Memory Inspector. Alan *From:*ParaView [mailto:paraview-boun...@paraview.org] *On Behalf Of *Léo Pessanha *Sent:* Thursday, February 13, 2014 11:22 AM *To:* ParaView list *Subject:* [EXTERNAL] [Paraview] Paraview

Re: [Paraview] PV3.14 How to create three equal size windows

Burlen Loring wrote: start with one split, and split both, but don't create a view in the last one. you should have 3 equal size views. Beautiful, many thanks. Stephen Saving screenshots only captures the 3 panels that have views. gui and screen shot On 1/4/2014 1:36 AM, Stephen Wornom

Re: [Paraview] PV3.14 How to create three equal size windows

window, the width of the title is limited. Is there an easy to delete the 4th window and have the three views spread over the full width of the visualization area. That way I could put a longer title. Hope my question is clear. Stephen gui and screen shot On 1/4/2014 1:36 AM, Stephen Wornom

[Paraview] PV3.14 How to create three equal size windows

I start with a single PV window. Using the icon I can split the window into two equally sized windows. When I split one of the two equally sized windows I get three windows BUT the sizes are different. What is the simplest approach to get three equally sized windows? Hope my question is clear.

[Paraview] adding music to an animation

I create an animation from the frame jpgs using convert. How does one add music to the animation? Thanks, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel: 04 92 38 50 54 Fax: 04 97 15 53 51 attachment:

Re: [Paraview] adding music to an animation

Utkarsh Ayachit wrote: What platform? On OsX you can use things like iMovie, I believe. Linux Fedora 16 64 bit. Stephen Utkarsh On Wed, Dec 11, 2013 at 9:54 AM, Stephen Wornom stephen.wor...@inria.fr mailto:stephen.wor...@inria.fr wrote: I create an animation from the frame jpgs

[Paraview] parallel paraview

I launch the paraview server on nef using 32 xeon cores. I am using the 64-bit PV. The server is listening on nef066. Paraview 3.14.1 has been install from the source and has been used successfully until now. Next I start paraview 3.14.1 (binary version) on my workstation. When I connect I get

Re: [Paraview] Annotate Time Filter

Hedieh Ebrahimi wrote: Hello, I have a question about AnnotateTimeFilter. I have a Data Set ( h5 files) containing several time steps that I open with PFlotran Reader. If i first merge these files and then open them as a single file using the PFlotran Reader, then the Annotate Time Filter

[Paraview] PV 4.01 How to get screenshot with menu

I do a screenshot but the menu is not included (only the contours), How does one include the menu? Thanks, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel: 04 92 38 50 54 Fax: 04 97 15 53 51 attachment:

[Paraview] romio on nef

nef: locate romio /opt/openmpi/1.6.3/lib64/openmpi/mca_io_romio.la /opt/openmpi/1.6.3/lib64/openmpi/mca_io_romio.so /opt/openmpi-gcc/1.6.3/lib64/openmpi/mca_io_romio.la /opt/openmpi-gcc/1.6.3/lib64/openmpi/mca_io_romio.so /opt/pgi/linux86-64/2013/mpi/mvapich/doc/romio-users.ps.gz nef: ll

Re: [Paraview] romio on nef

This was sent in error, please ignore, Stephen Stephen Wornom wrote: nef: locate romio /opt/openmpi/1.6.3/lib64/openmpi/mca_io_romio.la /opt/openmpi/1.6.3/lib64/openmpi/mca_io_romio.so /opt/openmpi-gcc/1.6.3/lib64/openmpi/mca_io_romio.la /opt/openmpi-gcc/1.6.3/lib64/openmpi/mca_io_romio.so /opt

[Paraview] PV 4.01 animating slices

I would like to animate x-slices of the same calculation (x= 0.1, ...) as opposed to animating a slice from different time solutions. In earlier versions one could specify how many slices desired and the step size (x= 0.1, 0.2, 0.3, ...etc). Is this feature somewhere to be found in PV 4.01?

Re: [Paraview] PV 4.01 animating slices

but the range in the icon -s -21.2 to 21.2. Thus The 12 planes that I requested are not correctly spaced. How do I animate the planes, 1 plane at time? Thanks, Stephen On Wed, Jul 17, 2013 at 7:21 AM, Stephen Wornom stephen.wor...@inria.fr wrote: I would like to animate x-slices of the same

Re: [Paraview] PV intermittent display images

for bring the immediate mode rendering to my attention, Stephen I had some strange effects recently, but I can't remember the details. JB -Original Message- From: paraview-boun...@paraview.org [mailto:paraview- boun...@paraview.org] On Behalf Of Stephen Wornom Sent: 03 July 2013 17:17

[Paraview] PV intermittent display images

I create an contour image using PV 4.01 using a 4 million point unstructured mesh. I see the image 1 sec, the next instance it disappears from my screen. If I move the mouse, or right click on the screen the image sometimes comes back for an instance. I cannot get the image to stay on my

[Paraview] PV 3.14.1 and 4.01 Calculator error

I have a real variable named K (as in K-Epsilon) When I compute K**2 using the calculator I get this error using the downloaded 64-bit binaries. ERROR: In /home/utkarsh/Kitware/superbuild/paraview/src/paraview/VTK/Common/vtkFunctionParser.cxx, line 1480 vtkFunctionParser (0x1e592530):

Re: [Paraview] PV 3.14.1 and 4.01 Calculator error

entries but 4.01 uses right-to-left entries Hope this makes some sense. Thanks, Stephen Utkarsh On Tue, Jul 2, 2013 at 10:11 AM, Stephen Wornom stephen.wor...@inria.fr wrote: I have a real variable named K (as in K-Epsilon) When I compute K**2 using the calculator I get this error using

Re: [Paraview] ANN: ParaView 4.0.0-RC1 now available for download

Utkarsh Ayachit wrote: Folks, In preparation of the next ParaView release, the ParaView 4.0.0, RC1 (Release Candidate 1) is now available for download (http://paraview.org/paraview/resources/software.php). We will have a detailed summary for the new features and enhancements in this release

Re: [Paraview] PV 3.98 visualizing 2D data

Felipe Bordeu wrote: you can use the Warp Scalar filter to warp your 2D domain in the z direction using a field. Thanks, works fine. Stephen Felipe Le 10/05/2013 10:18, Stephen Wornom a écrit : the data are x,y,variable Can paraview show the results in three dimensions with the variable

[Paraview] PV 3.14.1 64-bit trace save data question

After load the PV file (.pvtu) 1-I turn on trace do slice, clip, then contour save data 2-I turn off trace save the trace.py file When I edit the trace.py file everything is there EXCEPT the save data command. Is this normal? Thanks in advance, Stephen -- stephen.wor...@inria.fr 2004 route des

[Paraview] PV 3.98 ruler

Ruler has three option: x, y, or z directions. Is it possible to have a radius, say in the x,y plane sqrt(x**2+y**2) = 1? Hope my question is clear. Thanks, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel: 04 92 38 50 54 Fax: 04

[Paraview] viewing faces

The external boundaries of my unstructured mesh are composed of triangle faces. How can I view the external curved boundaries using ParaView? Thanks in advance, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel: 04 92 38 50 54

Re: [Paraview] What is the maximum file size Paraview can handle?

Pradeep Jha wrote: Hello, does anyone have any idea that if we are not short of computational resources, what is the maximum data file size that Paraview can handle? Depends on whether you are using the mpi or scalar version (scalar requires large local memory). Stephen Thank you, Pradeep

Re: [Paraview] Basic question about installing Paraview for parallel use

Pradeep Jha wrote: I want to use Paraview on a parallel cluster but I don't have the root permissions. So if I install Paraview locally in my account, can I still use it in parallel with all efficiency? Or do I need to bug the System Administrator of the parallel cluster to install in the

Re: [Paraview] Export animation in avi?

William Oquendo wrote: Dear all, I am using Paraview 3.98 on Mountain Lion. I would like to export an animation. The only format available now are ogv, or png/jpeg snapshots. Is there a way to export to avi? I know I can create an avi from a bunch of png/jpeg files, just would like to know if

[Paraview] high speed avi playback

My avi files have many time steps. mplayer -sstep 1 file.avi speeds up the playback but has a progress bar in the middle of the screen during the playback. Can anyone recommend a rapid linux playback method that has no progress bar? Thanks in advance, Stephen

[Paraview] PV 3.10.0 animation avi playback

I create an avi using mpi-PV with offscreen rendering. I note the following: 1-If the screensaver on my Linux Fedora 17 workstation is activated during the rendering process (For example, I go away from my workstation), and I use for playback mplayer -sstep 1 file.avi shows the progress bar

[Paraview] PV 3.14.1 64 bit time interpolation

What are the detailed steps involved to interpolate between data time steps? I click on temporal interpolation and enter an interval. I animate using paraview.pvd file but would like to have a smoother animation using interpolation between the data time steps. PV does not give an error but

Re: [Paraview] visualizing subdomain interfaces (boundaries) PV 3.10.0

. If you're working in serial you may be able to use the extract surface filter to see the interface between the partitions from the files. Andy On Thu, Sep 13, 2012 at 4:28 AM, Stephen Wornom stephen.wor...@inria.fr mailto:stephen.wor...@inria.fr wrote: I have parallel unstructured data .pvd

Re: [Paraview] visualizing subdomain interfaces (boundaries) PV 3.10.0

Andy Bauer wrote: That filter is only available if you're running pvserver in parallel. I believe it should be in 3.10. I don't see id scalars under filters. I am running in parallel. I can try PV 3.10.1 Stephen Andy On Fri, Sep 14, 2012 at 10:54 AM, Stephen Wornom stephen.wor...@inria.fr

Re: [Paraview] visualizing subdomain interfaces (boundaries) PV 3.10.0

, Stephen Wornom stephen.wor...@inria.fr mailto:stephen.wor...@inria.fr wrote: Andy Bauer wrote: That filter is only available if you're running pvserver in parallel. I believe it should be in 3.10. I don't see id scalars under filters. I am running in parallel. I

[Paraview] visualizing subdomain interfaces (boundaries)

I have parallel unstructured data .pvd .pvtu and vtu data for each subdomain. Is there an easy way to see the interfaces? I have a pressure abnormality and I would like to see if it ls located on a boundary between two domains. Thanks, Stephen -- stephen.wor...@inria.fr 2004 route des

[Paraview] PV 3.14.0 reset center

I see the icon reset center. I want to reset the center from 0,0,0 to 0,0,10. What are the steps to reset the center? Thanks, Stephen p.s. Must I reset the center before making a slice? -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel:

[Paraview] clip + renumeration

I have a 3D PV mesh. I would like to clip the top. Is it possible with ParaView to renumerate the vertices, volumes, faces of the mesh that remains? Hope my question is clear. Thanks, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX

Re: [Paraview] TimestepValues

Justin, Please include the e-mail to which you are answering or else no one knows what the question was. Stephen Justin Rodriguez wrote: Hi Sebastien, The files were all time dependent data but some had a TimeRange but no TimestepValues so I simply did: TimestepValues =

Re: [Paraview] High-order visualization

Indeed a nice job. I just click on the sample sample vtk and got this error. Probably something on my side. Stephen XML Parsing Error: not well-formed Location: http://perso.uclouvain.be/sebastien.blaise/vtkPlugin/sampleHighOrder.vtk Line Number 184, Column 2: Sebastien Jourdain wrote: Nice

Re: [Paraview] Surface Streamlines

hicham mach wrote: Hello, I'm a new user of ParaView. For my work, i need to plot streamlines on arbitrary surface. After many research, i found that the function SurfaceLIC I use PV 3.12.0: I would like very much to to plot streamlines on the surface of a cylinder but have not yet managed

[Paraview] PV 3.12.0 Is it possible to extract a contour?

I know how to extract surfaces using extract surface connectivity threshold When I create a contour, the contour does not appear as a selection when I try to extract the contour and click on threshold. Hope my question is clear, Thanks, Stephen -- stephen.wor...@inria.fr 2004 route des

[Paraview] PV 3.12.0 how to set offset screen rendering

How does one do it? Thanks in advance, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel: 04 92 38 50 54 Fax: 04 97 15 53 51 attachment: stephen_wornom.vcf___ Powered by www.kitware.com

[Paraview] PV 3.12.0 how to set offset screen rendering

How does one do it? I am using the downloaded binaries, does the binary version contain the offscreen option? Thanks in advance, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel: 04 92 38 50 54 Fax: 04 97 15 53 51

Re: [Paraview] How to extract the boundary of an unstructured grid?

Cory Quammen wrote: The Extract Surface filter in ParaView is probably what you want. What I do is to create a new variable Bnd that is zero at interior points and non-zero value(s) on the interfaces. Then Extract Surface Threshold (choose Bnd and the value of the interface) This works for

Re: [Paraview] PV 3.12.0-RC3 error while loading shared libraries: libbz2.so.1.0: cannot open shared object file: No such file or directory

Continue searching, Stephen _http://trunk.cdash.org/upload/55d090630fceab933307adc71b7d6f2335015e77/ParaView-3.12.0-RC3-85-g312ab75-Linux-x86_64.tar.gz_ On Mon, Nov 7, 2011 at 9:19 AM, Stephen Wornom stephen.wor...@inria.fr mailto:stephen.wor...@inria.fr wrote: Utkarsh Ayachit wrote

Re: [Paraview] PV 3.12.0-RC3 error while loading shared libraries: libbz2.so.1.0: cannot open shared object file: No such file or directory

Utkarsh Ayachit wrote: Can you try running the following and post the output: paraview dir/bin/paraview --ldd bin/paraview --ldd linux-vdso.so.1 = (0x7fff1a3ff000) libpqApplicationComponents.so =

Re: [Paraview] PV 3.12.0-RC3 error while loading shared libraries: libbz2.so.1.0: cannot open shared object file: No such file or directory

Utkarsh Ayachit wrote: Stephen, RC3 stands for ReleaseCandidate3 Utkarsh On Sat, Nov 5, 2011 at 6:19 AM, Stephen Wornomstephen.wor...@inria.fr wrote: David Partyka wrote: Hi Stephen, this is a bug that we addressed yesterday. I am generating a nightly binary, would you mind

Re: [Paraview] PV 3.12.0-RC3 error while loading shared libraries: libbz2.so.1.0: cannot open shared object file: No such file or directory

David Partyka wrote: Hi Stephen, this is a bug that we addressed yesterday. I am generating a nightly binary, would you mind trying it when it is done and let us know if the problem has gone away? I will send you a link shortly. Will test it immediately. Question: I know that the final release

[Paraview] PV 3.12.0-RC3 error while loading shared libraries: libbz2.so.1.0: cannot open shared object file: No such file or directory

I always download the 64-bit Paraview binary files. PV 3.10.1 worked fine as did previous versions. With PV-3.12.0 and PV-3.12.3 I get this error /home/swornom/ParaView-3.12.0-RC3-Linux-x86_64/lib/paraview-3.12/paraview: error while loading shared libraries: libbz2.so.1.0: cannot open shared

[Paraview] PV 3.10.1 cell data to point data

How does PV go from cell data to point data? Linear interpolation? or 2nd-order interpolation? on higher order than 2nd-order. Thanks in advance, Stephen -- stephen.wor...@inria.fr 2004 route des lucioles - BP93 Sophia Antipolis 06902 CEDEX Tel: 04 92 38 50 54 Fax: 04 97 15 53

Re: [Paraview] PV 3.10.1 cell data to point data

Moreland, Kenneth wrote: None of those. The cell data to point data filter just finds all cells neighboring each point and averages the cell values of those neighbors. Wow, not even a volume averaging? node value = sum (cell values * cell volume)/total volume Stephen -Ken On 10/18/11 8:26

[Paraview] PV 3.10.1 integration over a surface

How does one compute the integral of P Normal ds ? where Normal is the surface normal vector click on integrate variables computes the integral of P ds I would like Fx = integral of P nx ds where nx ds is the surface area normal to the x-direction. Hope my question is clear. Stephen p.s.

Re: [Paraview] PV 3.10.1 integration over a surface

the cell normal vector in the calculator list? Thanks for your help, Stephen Andy On Sun, Jun 19, 2011 at 4:01 AM, Stephen Wornom stephen.wor...@inria.fr mailto:stephen.wor...@inria.fr wrote: How does one compute the integral of P Normal ds ? where Normal is the surface normal vector

Re: [Paraview] PV 3.10.1 using python to slice and integrate variable

help. Stephen Pat On Wed, Jun 15, 2011 at 4:39 PM, Stephen Wornom stephen.wor...@inria.fr mailto:stephen.wor...@inria.fr wrote: We are using PV to analyze flow around a sphere. 1- We extract the surface of the sphere from the mean flow solution. 2- We make a slice in x (say

  1   2   >