Move GPIO pinmux to MDIO node. Add GB Ethernet reset GPIO.
Add PIN_INPUT to Fix SPE ethernet reset gpio so that
reading the GPIO can give correct status.
Signed-off-by: Roger Quadros <rog...@kernel.org>
---
arch/arm/dts/k3-am625-beagleplay.dts | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
diff --git a/arch/arm/dts/k3-am625-beagleplay.dts
b/arch/arm/dts/k3-am625-beagleplay.dts
index a34e0df2ab8..8ab838f1697 100644
--- a/arch/arm/dts/k3-am625-beagleplay.dts
+++ b/arch/arm/dts/k3-am625-beagleplay.dts
@@ -292,6 +292,8 @@
pinctrl-single,pins = <
AM62X_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC
*/
AM62X_IOPAD(0x015c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO
*/
+ AM62X_IOPAD(0x003c, PIN_INPUT, 7) /* (M25)
GPMC0_AD0.GPIO0_15 */
+ AM62X_IOPAD(0x018c, PIN_INPUT, 7) /* (AC21)
RGMII2_RD2.GPIO1_5 */
>;
};
@@ -383,7 +385,6 @@
AM62X_IOPAD(0x016c, PIN_INPUT, 1) /* (Y18)
RGMII2_TD0.RMII2_TXD0 */
AM62X_IOPAD(0x0170, PIN_INPUT, 1) /* (AA18)
RGMII2_TD1.RMII2_TXD1 */
AM62X_IOPAD(0x0164, PIN_INPUT, 1) /* (AA19)
RGMII2_TX_CTL.RMII2_TX_EN */
- AM62X_IOPAD(0x018c, PIN_OUTPUT, 7) /* (AC21)
RGMII2_RD2.GPIO1_5 */
AM62X_IOPAD(0x0190, PIN_INPUT, 7) /* (AE22)
RGMII2_RD3.GPIO1_6 */
AM62X_IOPAD(0x01f0, PIN_OUTPUT, 5) /* (A18)
EXT_REFCLK1.CLKOUT0 */
>;
@@ -597,6 +598,9 @@
cpsw3g_phy0: ethernet-phy@0 {
reg = <0>;
+ reset-gpios = <&main_gpio0 15 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <50000>;
};
cpsw3g_phy1: ethernet-phy@1 {
@@ -615,7 +619,7 @@
"USR0", "USR1", "USR2", "USR3", "", "", "USR4", /* 3-9 */
"EEPROM_WP", /* 10 */
"CSI2_CAMERA_GPIO1", "CSI2_CAMERA_GPIO2", /* 11-12 */
- "CC1352P7_BOOT", "CC1352P7_RSTN", "", "", "", /* 13-17 */
+ "CC1352P7_BOOT", "CC1352P7_RSTN", "GBE_RSTN", "", "", /*
13-17 */
"USR_BUTTON", "", "", "", "", "", "", "", "", /* 18-26 */
"", "", "", "", "", "", "", "", "", "HDMI_INT", /* 27-36 */
"", "VDD_WLAN_EN", "", "", "WL_IRQ", "GBE_INTN",/* 37-42 */
--
2.34.1
