Did you copy android file system to SD 2nd partition? 2010/3/29 anil <anilba...@gmail.com>
> hello all, > > This is Anil, i am very new to this group. when i try to port my > eclair into my devkit8000 board i am getting the following log > messages.please help me in this reguard. > > the logcat message are as follows > > reading uImage > > 2167832 bytes read > ## Booting kernel from Legacy Image at 80200000 ... > Image Name: Linux-2.6.29-omap1 > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 2167768 Bytes = 2.1 MB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > Uncompressing > > Linux............................................................................................................................................ > done, booting the kernel. > Linux version 2.6.29-omap1 (r...@trng-desktop) (gcc version 4.3.3 > (Sourcery G++ Lite 2009q1-203) ) #5 Thu Mar 25 13:35:36 IST 2010 > CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387f > CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache > Machine: OMAP3 Beagle Board > Memory policy: ECC disabled, Data cache writeback > L2 CACHE is enabled in bootloader > OMAP3430 ES3.1 > SRAM: Mapped pa 0x40200000 to va 0xfc800000 size: 0x100000 > Reserving 16777216 bytes SDRAM for VRAM > Built 1 zonelists in Zone order, mobility grouping on. Total pages: > 32512 > Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/ > mmcblk0p2 omapdss.def_disp=4.3inch_lcd init=/init rootfstype=ext3 rw > rootdelay=1 nohz=off > Clocking rate (Crystal/DPLL/ARM core): 26.0/266/500 MHz > Reprogramming SDRC > dpll3_m2_clk rate change failed: -22 > GPMC revision 5.0 > IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts > Total of 96 interrupts on 1 active controller > OMAP34xx GPIO hardware version 2.5 > PID hash table entries: 512 (order: 9, 2048 bytes) > OMAP clockevent source: GPTIMER12 at 32768 Hz > Console: colour dummy device 80x30 > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) > Memory: 128MB = 128MB total > Memory: 108500KB available (3980K code, 723K data, 168K init) > Calibrating delay loop... 491.57 BogoMIPS (lpj=1921024) > Mount-cache hash table entries: 512 > CPU: Testing write buffer coherency: ok > net_namespace: 520 bytes > regulator: core version 0.5 > NET: Registered protocol family 16 > Found NAND on CS0 > Registering NAND on CS0 > OMAP DMA hardware revision 4.0 > bio: create slab <bio-0> at 0 > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz > twl4030: PIH (irq 7) chaining IRQs 368..375 > twl4030: power (irq 373) chaining IRQs 376..383 > twl4030: gpio (irq 368) chaining IRQs 384..401 > beagle_twl_gpio_setup:246 > twl4030_mmc_init:367 > twl4030_mmc_init:382 > regulator: VMMC1: 1850 <--> 3150 mV normal standby > regulator: VDAC: 1800 mV normal standby > regulator: VUSB1V5: 1500 <--> 0 mV normal standby > regulator: VUSB1V8: 1800 <--> 0 mV normal standby > regulator: VUSB3V1: 3100 <--> 0 mV normal standby > regulator: VPLL2: 1800 mV normal standby > regulator: VSIM: 1800 <--> 3000 mV normal standby > i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz > SCSI subsystem initialized > twl4030_usb twl4030_usb: Initialized TWL4030 USB module > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > Bluetooth: Core ver 2.15 > NET: Registered protocol family 31 > Bluetooth: HCI device and connection manager initialized > Bluetooth: HCI socket layer initialized > musb_hdrc: version 6.0, musb-dma, host, debug=0 > musb_hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92 > musb_hdrc musb_hdrc: MUSB HDRC host driver > musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 > usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: MUSB HDRC host driver > usb usb1: Manufacturer: Linux 2.6.29-omap1 musb-hcd > usb usb1: SerialNumber: musb_hdrc > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > NET: Registered protocol family 2 > IP route cache hash table entries: 1024 (order: 0, 4096 bytes) > TCP established hash table entries: 4096 (order: 3, 32768 bytes) > TCP bind hash table entries: 4096 (order: 2, 16384 bytes) > TCP: Hash tables configured (established 4096 bind 4096) > TCP reno registered > NET: Registered protocol family 1 > NetWinder Floating Point Emulator V0.97 (double precision) > ashmem: initialized > VFS: Disk quotas dquot_6.5.2 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. > msgmni has been set to 212 > alg: No test for stdrng (krng) > io scheduler noop registered > io scheduler anticipatory registered (default) > io scheduler deadline registered > io scheduler cfq registered > OMAP DSS rev 2.0 > OMAP DISPC rev 3.0 > OMAP VENC rev 2 > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 > serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 > serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 > console [ttyS2] enabled > brd: module loaded > loop: module loaded > dm9000 Ethernet Driver, V1.31 > Linux video capture interface: v2.00 > i2c /dev entries driver > Driver 'sd' needs updating - please use bus_type methods > omap2-nand driver initializing > NAND device: Manufacturer ID: 0x2c, Chip ID: 0xb1 (Micron NAND 128MiB > 1,8V 16-bit) > cmdlinepart partition parsing not available > Creating 5 MTD partitions on "omap2-nand": > 0x000000000000-0x000000080000 : "X-Loader" > 0x000000080000-0x000000260000 : "U-Boot" > 0x000000260000-0x000000280000 : "U-Boot Env" > 0x000000280000-0x000000680000 : "Kernel" > 0x000000680000-0x000008000000 : "File System" > usbmon: debugfs is not available > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > ehci-omap ehci-omap.0: OMAP-EHCI Host Controller > ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2 > ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 > ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 > usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb2: Product: OMAP-EHCI Host Controller > usb usb2: Manufacturer: Linux 2.6.29-omap1 ehci_hcd > usb usb2: SerialNumber: ehci-omap.0 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 3 ports detected > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma) > android init > input: gpio-keys as /devices/platform/gpio-keys/input/input0 > twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0 > twl4030_rtc twl4030_rtc: Power up reset detected. > twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC. > Bluetooth: Virtual HCI driver ver 1.2 > Bluetooth: HCI UART driver ver 2.2 > Bluetooth: HCI H4 protocol initialized > Bluetooth: HCI BCSP protocol initialized > Bluetooth: HCILL protocol initialized > Bluetooth: Broadcom Blutonium firmware driver ver 1.2 > usbcore: registered new interface driver bcm203x > Bluetooth: Digianswer Bluetooth USB driver ver 0.10 > usbcore: registered new interface driver bpa10x > Bluetooth: BlueFRITZ! USB driver ver 1.2 > usbcore: registered new interface driver bfusb > Bluetooth: Generic Bluetooth USB driver ver 0.5 > usbcore: registered new interface driver btusb > Bluetooth: Generic Bluetooth SDIO driver ver 0.1 > Registered led device: beagleboard::usr0 > Registered led device: beagleboard::usr1 > Registered led device: beagleboard::pmu_stat > usbcore: registered new interface driver usbhid > usbhid: v2.6:USB HID core driver > logger: created 64K log 'log_main' > logger: created 256K log 'log_events' > logger: created 64K log 'log_radio' > Advanced Linux Sound Architecture Driver Version 1.0.18a. > No device for DAI twl4030 > No device for DAI twl4030 Voice > No device for DAI twl4030 Clock > No device for DAI omap-mcbsp-dai-0 > No device for DAI omap-mcbsp-dai-1 > No device for DAI omap-mcbsp-dai-2 > No device for DAI omap-mcbsp-dai-3 > No device for DAI omap-mcbsp-dai-4 > OMAP3 Beagle SoC init > TWL4030 Audio Codec init > asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok > ALSA device list: > #0: omap3beagle (twl4030) > TCP cubic registered > NET: Registered protocol family 17 > NET: Registered protocol family 15 > Bluetooth: L2CAP ver 2.13 > Bluetooth: L2CAP socket layer initialized > Bluetooth: SCO (Voice Link) ver 0.6 > Bluetooth: SCO socket layer initialized > Bluetooth: RFCOMM socket layer initialized > Bluetooth: RFCOMM TTY layer initialized > Bluetooth: RFCOMM ver 1.11 > Bluetooth: BNEP (Ethernet Emulation) ver 1.3 > Bluetooth: BNEP filters: protocol multicast > Bluetooth: HIDP (Human Interface Emulation) ver 1.2 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > Power Management for TI OMAP3. > VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev > 1 > Console: switching to colour frame buffer device 80x30 > mmc0: new SD card at address e624 > mmcblk0: mmc0:e624 SD01G 968 MiB > mmcblk0:<4>omapdss DPI: Could not find exact pixel clock. Requested > 23500 kHz, got 24000 kHz > p1 p2 > twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 > UTC (946684800) > Waiting 1sec before mounting root device... > VP1:TRANXDONE timeout exceeded going ahead with the t2 > smps wait > VP1:TRANXDONE timeout exceeded going ahead with the t2 > smps wait > kjournald starting. Commit interval 5 seconds > EXT3-fs warning: maximal mount count reached, running e2fsck is > recommended > EXT3 FS on mmcblk0p2, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > VFS: Mounted root (ext3 filesystem) on device 179:2. > Freeing init memory: 168K > Warning: unable to open an initial console. > init: cannot open '/initlogo.rle' > init: Unable to open persistent property directory /data/property > errno: 2 > init: cannot find '/system/bin/playmp3', disabling 'bootsound' > init: cannot find '/system/etc/install-recovery.sh', disabling > 'flash_recovery' > sh: can't access tty; job control turned off > # warning: `rild' uses 32-bit capabilities (legacy support in use) > init: untracked pid 773 exited > init: untracked pid 787 exited > VP1:TRANXDONE timeout exceeded going ahead with the t2 > smps wait > VP1:TRANXDONE timeout exceeded going ahead with the t2 > smps wait > logcat & > # VP1:TRANXDONE timeout exceeded going ahead with > the t2 smps wait > init: untracked pid 799 exited > I/DEBUG ( 770): debuggerd: Mar 24 2010 18:19:16 > I/vold ( 768): Android Volume Daemon version 2.0 > W/libdbus ( 774): Failed to start message bus: Failed to open "/etc/ > dbus.conf": Permission denied > E/keystore( 778): chdir: /data/misc/keystore: No such file or > directory > E/vold ( 768): Unable to chdir to /sys/class/mmc_host/mmc0/ > slot_name (Not a directory) > E/vold ( 768): Error bootstrapping card '/sys/class/mmc_host/mmc0/ > slot_name' (Not a directory) > I/vold ( 768): New MMC card 'SD01G' (serial 1356943616) added @ / > devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:e624 > I/vold ( 768): Disk (blkdev 179:0), 1984000 secs (968 MB) 2 > partitions > I/vold ( 768): New blkdev 179.0 on media SD01G, media path / > devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:e624, Dpp 2 > I/vold ( 768): Partition (blkdev 179:1), 819252 secs (400 MB) type > 0xc > I/vold ( 768): New blkdev 179.1 on media SD01G, media path / > devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:e624, Dpp 1 > I/vold ( 768): Partition (blkdev 179:2), 1156680 secs (564 MB) > type 0x83 > I/vold ( 768): New blkdev 179.2 on media SD01G, media path / > devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:e624, Dpp 0 > D/vold ( 768): Bootstrapping complete > D/AndroidRuntime( 772): > D/AndroidRuntime( 772): >>>>>>>>>>>>>> AndroidRuntime START > <<<<<<<<<<<<<< > D/AndroidRuntime( 772): CheckJNI is ON > E/dalvikvm( 772): Can't open dex cache '/data/dalvik-cache/ > sys...@framework@core....@classes.dex': No such file or directory > I/dalvikvm( 772): Unable to open or create cache for /system/ > framework/core.jar (/data/dalvik-cache/ > sys...@framework@core....@classes.dex) > D/dalvikvm( 772): Unable to process classpath element '/system/ > framework/core.jar' > E/dalvikvm( 772): Can't open dex cache '/data/dalvik-cache/ > sys...@framework@ext....@classes.dex': No such file or directory > I/dalvikvm( 772): Unable to open or create cache for /system/ > framework/ext.jar (/data/dalvik-cache/ > sys...@framework@ext....@classes.dex) > D/dalvikvm( 772): Unable to process classpath element '/system/ > framework/ext.jar' > E/dalvikvm( 772): Can't open dex cache '/data/dalvik-cache/ > sys...@framework@framework....@classes.dex': No such file or directory > I/dalvikvm( 772): Unable to open or create cache for /system/ > framework/framework.jar (/data/dalvik-cache/ > sys...@framework@framework....@classes.dex) > D/dalvikvm( 772): Unable to process classpath element '/system/ > framework/framework.jar' > E/dalvikvm( 772): Can't open dex cache '/data/dalvik-cache/ > sys...@framework@android.policy....@classes.dex': No such file or > directory > I/dalvikvm( 772): Unable to open or create cache for /system/ > framework/android.policy.jar (/data/dalvik-cache/ > sys...@framework@android.policy....@classes.dex) > D/dalvikvm( 772): Unable to process classpath element '/system/ > framework/android.policy.jar' > E/dalvikvm( 772): Can't open dex cache '/data/dalvik-cache/ > sys...@framework@services....@classes.dex': No such file or directory > I/dalvikvm( 772): Unable to open or create cache for /system/ > framework/services.jar (/data/dalvik-cache/ > sys...@framework@services....@classes.dex) > D/dalvikvm( 772): Unable to process classpath element '/system/ > framework/services.jar' > E/dalvikvm( 772): ERROR: no valid entries found in bootclasspath '/ > system/framework/core.jar:/system/framework/ext.jar:/system/framework/ > framework.jar:/system/framework/android.policy.jar:/system/framework/ > services.jar' > D/dalvikvm( 772): VM cleaning up > D/dalvikvm( 772): LinearAlloc 0x0 used 4100 of 5242880 (0%) > W/dalvikvm( 772): JNI_CreateJavaVM failed > E/AndroidRuntime( 772): JNI_CreateJavaVM failed > I/ ( 787): ServiceManager: 0xad08 > W/AudioHardwareInterface( 787): Using stubbed audio hardware. No > sound will be produced. > D/AudioHardwareInterface( 787): setMode(NORMAL) > I/CameraService( 787): CameraService started: pid=787 > I/AudioFlinger( 787): AudioFlinger's thread 0xb370 ready to run > E/keystore( 794): chdir: /data/misc/keystore: No such file or > directory > W/libdbus ( 793): Failed to start message bus: Failed to open "/etc/ > dbus.conf": Permission denied > D/AndroidRuntime( 792): > D/AndroidRuntime( 792): >>>>>>>>>>>>>> AndroidRuntime START > <<<<<<<<<<<<<< > D/AndroidRuntime( 792): CheckJNI is ON > E/dalvikvm( 792): Can't open dex cache '/data/dalvik-cache/ > sys...@framework@core....@classes.dex': No such file or directory > I/dalvikvm( 792): Unable to open or create cache for /system/ > framework/core.jar (/data/dalvik-cache/ > sys...@framework@core....@classes.dex) > > -- > unsubscribe: > android-kernel+unsubscr...@googlegroups.com<android-kernel%2bunsubscr...@googlegroups.com> > website: http://groups.google.com/group/android-kernel > > To unsubscribe from this group, send email to android-kernel+ > unsubscribegooglegroups.com or reply to this email with the words "REMOVE > ME" as the subject. > -- unsubscribe: android-kernel+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-kernel To unsubscribe, reply using "remove me" as the subject.
