Can you enable early printk in the kernel? BTW, did you compile your Kernel with the right defconfig?
I have seen such problems in past, when I forgot to use the correct defconfig file ... - Akash On Mon, Aug 2, 2010 at 9:00 AM, ErCa <lindahl.e...@gmail.com> wrote: > Hi, hopefully this is the correct place to post this. > > I´m developing a device on a beagleboard and have some problems > starting the kernel. > I´m using yaffs2 as root filesystem and the version of the kernel is > 2.6.29. > We have the latest yaffs2 code compiled into the kernel, not from > googles kernel but from yaffs git sources. > We come so far as it has finished uncompressing the kernel and tried > booting it but after that it freezes without no output what so ever. > > The uBoot enviroment is as following: > > OMAP3_Kajsa # printenv > bootdelay=10 > baudrate=115200 > loadaddr=0x82000000 > usbtty=cdc_acm > console=ttyS0,115200n8 > loadbootscript=fatload mmc 0 ${loadaddr} boot.scr > bootscript=echo Running bootscript from mmc ...; source ${loadaddr} > loaduimage=fatload mmc 0 ${loadaddr} uImage > netmask=255.255.255.0 > gatewayip=192.168.0.99 > dieid#=1d5a0004000000000403643203019007 > ethact=smc911x-0 > ethaddr=00:11:22:33:44:55 > ipaddr=10.0.0.2 > serverip=10.0.0.1 > echo=Booting from nand ... > nandargs=console=ttyS0,115200n8 root=/dev/mtdblock4 opamfb.mode=lcd > vram=32M omapfb.vram=0:8M rdinit=/init rootwait rootfstype=yaffs2 > nandboot=echo Booting from NAND...; nand read ${loadaddr} 280000 > 400000; bootm ${loadaddr} > bootfile=uMulti-2 > bootargs=console=ttyS0,115200n8 root=/dev/mtdblock4 rw opamfb.mode=lcd > vram=32M omapfb.vram=0:8M init=/init rootwait rootfstype=yaffs2 > stdin=serial > stdout=serial > stderr=serial > > Environment size: 1175/131068 bytes > > > And the output when we start to boot the kernel is: > > OMAP3_Kajsa # set ethaddr 00:11:22:33:44:55 ; set ipaddr 10.0.0.2 ; > set serverip 10.0.0.1 ; tftp 0x82000000 uImage-yaffs > smc911x: detected LAN9220 controller > smc911x: phy initialized > smc911x: MAC 00:11:22:33:44:55 > Using smc911x-0 device > TFTP from server 10.0.0.1; our IP address is 10.0.0.2 > Filename 'uImage-yaffs'. > Load address: 0x82000000 > Loading: T > ################################################################# > > ################################################################# > ############################### > done > Bytes transferred = 2360952 (240678 hex) > OMAP3_Kajsa # bootm > ## Booting kernel from Legacy Image at 82000000 ... > Image Name: Linux-2.6.29-rc3-omap1-gb7a2014- > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 2360888 Bytes = 2.3 MB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > Uncompressing > > Linux...................................................................................................................................................... > done, booting the kernel. > > > We have also tried to write the kernel to NAND and booted from there > with the same result. > > > Any input will be appriciated. > Best regards. > Eric > > -- > unsubscribe: > android-kernel+unsubscr...@googlegroups.com<android-kernel%2bunsubscr...@googlegroups.com> > website: http://groups.google.com/group/android-kernel -- unsubscribe: android-kernel+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-kernel