also check the firewall settings of the system you try to connect to

On Wed, Aug 4, 2010 at 10:56 AM, Manvendra Pratap Singh
<manav....@gmail.com> wrote:
> Can you post your bootargs ?
> If you check your boot log, here the "rootpath" is empty. May be you are not
> able to set your bootargs properly.
> On Wed, Aug 4, 2010 at 12:52 PM, sri <sresin...@gmail.com> wrote:
>>
>> Hi,
>> I am unable to boot kernel for omap 2430 board with 2.6.14.7.
>>
>> I get following message :
>> Starting
>> kernel ...
>>
>> Uncompressing
>> Linux..............................................................
>> Linux version 2.6.14.7-arm1-omap2 (r...@infba01539) (gcc version 4.4.1
>> (Sourcery0
>> CPU: TI OMAP2430 (ARM1136JF-S) [4107b366] revision 6
>> (ARMv6TEJ)
>> Machine: OMAP24xx
>> 2430SDP
>> Memory policy: ECC disabled, Data cache
>> writeback
>> OMAP24302
>> Power Management for TI
>> OMAP.
>> Clocking rate (xtal/DPLL/MPU): 13.0/660/330
>> MHz
>> clock.c: Enable for dpll_ck without enable
>> code
>> Disabling unused clock "i2chs2_fck"... <6>
>> done
>> Disabling unused clock "i2c2_ick"... <6>
>> done
>> Disabling unused clock "i2chs1_fck"... <6>
>> done
>> Disabling unused clock "i2c1_ick"... <6>
>> done
>> Disabling unused clock "wdt1_ick"... <6>
>> done
>> Disabling unused clock "mpu_wdt_fck"... <6>
>> done
>> Disabling unused clock "mpu_wdt_ick"... <6>
>> done
>> Disabling unused clock "gpios_fck"... <6>
>> done
>> Disabling unused clock "gpios_ick"... <6>
>> done
>> Disabling unused clock "gpt2_fck"... <6>
>> done
>> Disabling unused clock "gpt2_ick"... <6>
>> done
>> Disabling unused clock "mdm_osc_ck"... <6>
>> done
>> CPU0: D VIPT write-back
>> cache
>> CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256
>> sets
>> CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256
>> sets
>> Built 1
>> zonelists
>> Kernel command line: console=ttyS0,115200n8 root=172.28.6.33:/dev/nfs
>> rw noinitrM
>> IRQ: Found an INTC at 0x480fe000 (revision 3.0) with 96
>> interrupts
>> Total of 96 interrupts on 1 active
>> controller
>> OMAP GPIO hardware version
>> 2.4
>> PID hash table entries: 256 (order: 8, 4096
>> bytes)
>> OMAP GPTimer1 hardware version
>> 1.6
>> OMAP GPTimer2 hardware version
>> 1.6
>> Console: colour dummy device
>> 80x30
>> Dentry cache hash table entries: 8192 (order: 3, 32768
>> bytes)
>> Inode-cache hash table entries: 4096 (order: 2, 16384
>> bytes)
>> Memory: 32MB = 32MB
>> total
>> Memory: 29104KB available (2563K code, 563K data, 120K
>> init)
>> Mount-cache hash table entries:
>> 512
>> CPU: Testing write buffer coherency:
>> ok
>> softlockup thread 0 started
>> up.
>> NET: Registered protocol family
>> 16
>> OMAP DMA4 hardware Initialized (max
>> lch=32)
>> omap2_disp: timeout waiting for display controller
>> reset
>> OMAP Display hardware version
>> 1.0
>> OMAP virtual buses
>> initialized
>> Registering OMAP device 'OMAP24xx I2C 03'. Parent at
>> L4CORE
>> Registering OMAP device 'OMAP24xx I2C 13'. Parent at
>> L4CORE
>> TWL4030 Power Companion
>> Active
>> TWL4030: Driver registration
>> complete.
>> usbcore: registered new driver
>> usbfs
>> usbcore: registered new driver
>> hub
>> musb_hdrc: version 2.2a/db-0.5.2, musb-dma, otg (peripheral+host),
>> debug=0
>> musb_hdrc: MHDRC RTL version
>> 1.400
>> musb_hdrc: USB OTG mode controller at c2800000 using DMA, IRQ
>> 92
>> Registering OMAP device 'omap-ostimer21'. Parent at
>> L4CORE
>> NetWinder Floating Point Emulator V0.97 (double
>> precision)
>> VFS: Disk quotas
>> dquot_6.5.1
>> Dquot-cache hash table entries: 1024 (order 0, 4096
>> bytes)
>> JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat,
>> Inc.
>> Initializing Cryptographic
>> API
>> Registering OMAP device 'sdp2430_lcd9'. Parent at
>> L3
>> Registering OMAP device 'sdp2430_tv10'. Parent at
>> L3
>> Registering OMAP device 'omap24xxfb6'. Parent at
>> L3
>> omap24xxfb: Options
>> "<NULL>"
>> Console: switching to colour frame buffer device
>> 30x40
>> omap24xxfb: fb0 frame buffer
>> device
>> omap24xxfb: display mode 240x320x16 hsync 19kHz vsync
>> 58Hz
>> OMAP Watchdog Timer: initial timeout 60
>> sec
>> Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing
>> disabled
>> ttyS0 at MMIO 0x4806a000 (irq = 72) is a
>> ST16654
>> ttyS1 at MMIO 0x4806c000 (irq = 73) is a
>> ST16654
>> ttyS2 at MMIO 0x4806e000 (irq = 74) is a
>> ST16654
>> TWL4030 GPIO Demux: IRQ Range 265 to 274, Initialization
>> Success
>> phy_clk_ctrl_sts =
>> 0x0
>> Initializing TWL4030 USB module (v0451,
>> pc002)
>> io scheduler noop
>> registered
>> io scheduler anticipatory
>> registered
>> io scheduler deadline
>> registered
>> io scheduler cfq
>> registered
>> RAMDISK driver initialized: 16 RAM disks of 16384K size 1024
>> blocksize
>> loop: loaded (max 8
>> devices)
>>  OMAP Timer32K is
>> initialized
>> Registering OMAP device 'omap-twl4030rtc16'. Parent at
>> L4CORE
>> omap-twl4030rtc:TWL4030-RTC Power up reset
>> detected.
>> omap-twl4030rtc:Enabling TWL4030-
>> RTC.
>> TWL4030 LEDS: Driver registration
>> complete.
>> smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre
>> <n...@cam.org>
>> eth0: SMC91C94 (rev 9) at c2856300 IRQ 245
>> [nowait]
>> eth0: Ethernet addr:
>> 08:00:28:01:04:52
>> netconsole: not configured,
>> aborting
>> Linux video capture interface:
>> v1.00
>> Registering OMAP device 'omap24xxcam0'. Parent at
>> L3
>> EX3691:Failed to detect EX3691
>> SOC.
>> omap24xxcam: cannot initialize
>> sensor
>> Registering OMAP device 'omap24xxvout111'. Parent at
>> L3
>> omap24xxvout: registered device video1
>> [v4l2]
>> Registering OMAP device 'omap24xxvout212'. Parent at
>> L3
>> omap24xxvout: registered device video2
>> [v4l2]
>> OMAP HDQ Hardware Revision 0.3. Driver in interrupt
>> mode.
>> omapflash.1: Found 1 x16 devices at 0x0 in 16-bit
>> bank
>> omapflash.1: Found 1 x16 devices at 0x2000000 in 16-bit
>> bank
>>  Intel/Sharp Extended Query Table at
>> 0x010A
>>  Intel/Sharp Extended Query Table at
>> 0x010A
>>  Intel/Sharp Extended Query Table at
>> 0x010A
>>  Intel/Sharp Extended Query Table at
>> 0x010A
>>  Intel/Sharp Extended Query Table at
>> 0x010A
>> Using buffer write
>> method
>> cfi_cmdset_0001: Erase suspend on write
>> enabled
>> Creating 4 MTD partitions on "omapflash.
>> 1":
>> 0x00000000-0x00040000 :
>> "bootloader"
>> 0x00040000-0x00060000 :
>> "params"
>> 0x00060000-0x00260000 :
>> "kernel"
>> 0x00260000-0x04000000 :
>> "filesystem"
>> omapflash.0: Found 1 x16 devices at 0x0 in 16-bit
>> bank
>> omapflash.0: Found 1 x16 devices at 0x4000000 in 16-bit
>> bank
>>  Intel/Sharp Extended Query Table at
>> 0x010A
>>  Intel/Sharp Extended Query Table at
>> 0x010A
>>  Intel/Sharp Extended Query Table at
>> 0x010A
>>  Intel/Sharp Extended Query Table at
>> 0x010A
>> Using buffer write
>> method
>> cfi_cmdset_0001: Erase suspend on write
>> enabled
>> Creating 4 MTD partitions on "omapflash.
>> 0":
>> 0x00000000-0x00040000 :
>> "(sibley)bootloader"
>> 0x00040000-0x00080000 :
>> "(sibley)params"
>> 0x00080000-0x00280000 :
>> "(sibley)kernel"
>> 0x00280000-0x08000000 :
>> "(sibley)filesystem"
>> NAND: Unable to find NAND settings in GPMC Configuration -
>> quitting
>> oneNAND: Unable to find oneNAND configuration in GPMC -
>> quitting
>> usbmon: debugfs is not
>> available
>> usbcore: registered new driver
>> hset
>> Registering OMAP device 'omap_twl4030keypad1'. Parent at
>> L4CORE
>> Registering OMAP device 'omap_tsc20468'. Parent at
>> L4CORE
>> Registering OMAP device 'omap2430-mmc12'. Parent at
>> L3
>> Registering OMAP device 'omap2430-mmc217'. Parent at
>> L3
>> Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22
>> 13:55:50 .
>> Registering OMAP device 'omap-dasf7'. Parent at
>> L3
>> OMAP243X TWL4030 Audio Support: Chip Rev[0x2f]
>> Initialized
>> audio support
>> initialized
>> Register_alsa_drv: Created ti_dasf
>> class
>> Register_alsa_drv: Created alsaDasf
>> class
>> [omap2_dasf_mailbox.c:[dasf_init_mailbox]
>> start
>> ALSA device
>> list:
>>  #0:
>> TWL4030
>> NET: Registered protocol family
>> 2
>> IP route cache hash table entries: 512 (order: -1, 2048
>> bytes)
>> TCP established hash table entries: 2048 (order: 1, 8192
>> bytes)
>> TCP bind hash table entries: 2048 (order: 1, 8192
>> bytes)
>> TCP: Hash tables configured (established 2048 bind
>> 2048)
>> TCP reno
>> registered
>> TCP bic
>> registered
>> NET: Registered protocol family
>> 1
>> NET: Registered protocol family
>> 17
>> NET: Registered protocol family
>> 15
>> Registering OMAP device 'omap-dxdev19'. Parent at
>> L4CORE
>> Registering OMAP device 'omap-sdram20'. Parent at
>> L3
>> VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev
>> 2
>> OMAP GPIO switch handler
>> initializing
>> eth0: link
>> up
>> IP-Config:
>> Complete:
>>      device=eth0, addr=172.28.6.34, mask=255.255.255.0,
>> gw=255.255.255.255,
>>     host=172.28.6.34, domain=, nis-
>> domain=(none),
>>     bootserver=172.28.6.33, rootserver=172.28.6.33,
>> rootpath=
>> Looking up port of RPC 100003/2 on
>> 172.28.6.33
>> portmap: server 172.28.6.33 not responding, timed
>> out
>> Root-NFS: Unable to get nfsd port number from server, using
>> default
>> Looking up port of RPC 100005/1 on
>> 172.28.6.33
>> portmap: server 172.28.6.33 not responding, timed
>> out
>> Root-NFS: Unable to get mountd port number from server, using
>> default
>> Root-NFS: Server returned error -5 while mounting /nfsroot/
>> rootfs
>> VFS: Unable to mount root fs via NFS, trying
>> floppy.
>> VFS: No root yet, retrying to mount root on 172.28.6.33:/dev/nfs
>> (unknown-block()
>> VFS: No root yet, retrying to mount root on 172.28.6.33:/dev/nfs
>> (unknown-block()
>> VFS: No root yet, retrying to mount root on 172.28.6.33:/dev/nfs
>> (unknown-block()
>> VFS: No root yet, retrying to mount root on 172.28.6.33:/dev/nfs
>> (unknown-block()
>> VFS: No root yet, retrying to mount root on 172.28.6.33:/dev/nfs
>> (unknown-block()
>> VFS: No root yet, retrying to mount root on 172.28.6.33:/dev/nfs
>> (unknown-block()
>> VFS: Cannot open root device "172.28.6.33:/dev/nfs" or unknown-
>> block(2,0)
>> Please append a correct "root=" boot
>> option
>> Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-
>> block(2,0)
>>
>>
>> Can anyone tell me what is going on wrong?
>>
>>
>> Thanks,
>> Sri.
>>
>> --
>> unsubscribe: android-kernel+unsubscr...@googlegroups.com
>> website: http://groups.google.com/group/android-kernel
>
>
> --
> Manav
>
> --
> unsubscribe: android-kernel+unsubscr...@googlegroups.com
> website: http://groups.google.com/group/android-kernel

-- 
unsubscribe: android-kernel+unsubscr...@googlegroups.com
website: http://groups.google.com/group/android-kernel

Reply via email to