OK sorry, I didn't realize you were in the proctorlabs environment. If you
don't hear back from Marko or Tyson I would notify support on this because it
can take away valuable lab time!!
From: Amer Mustafa [mailto:[email protected]]
Sent: Saturday, October 23, 2010 3:28 PM
To: Di Bias, Steve
Cc: [email protected]
Subject: Re: [OSL | CCIE_RS] Workbook 1 LAB 18.
Steve,
They were down because there was no DLCI assigned in the sub-interfaces ( all
routes ), You are right with the config below, this is exact same avilable on
ipexpert site for manual configuration on the routers.
But i guess when you load the configs through script on proctorlabs they come
up without frame-relay interface-dlci assigned.
regards ...
Amer
On Sun, Oct 24, 2010 at 1:20 AM, Di Bias, Steve
<[email protected]<mailto:[email protected]>> wrote:
Can you be more specific? Why were they "down"? There was no DLCI's configured?
The wrong DLCI's were configured? The wrong LMI type?
I just looked at the initials configs for VOL1 LAB18 and everything is
configured just fine
R2
interface Serial0/1/0
no ip address
encapsulation frame-relay
no arp frame-relay
no frame-relay inverse-arp
frame-relay lmi-type cisco
no shutdown
!
interface Serial0/1/0.24 point-to-point
ip address 150.50.24.2 255.255.255.252
frame-relay interface-dlci 204
!
interface Serial0/1/0.25 point-to-point
ip address 150.50.25.2 255.255.255.252
frame-relay interface-dlci 205
!
interface Serial0/1/0.26 point-to-point
ip address 150.50.26.2 255.255.255.252
frame-relay interface-dlci 206
R4
interface Serial0/0/0
no ip address
encapsulation frame-relay
no arp frame-relay
no frame-relay inverse-arp
frame-relay lmi-type cisco
no shutdown
!
interface Serial0/0/0.24 point-to-point
ip address 150.50.24.1 255.255.255.252
frame-relay interface-dlci 402
R5
interface Serial0/1/0
no ip address
encapsulation frame-relay
no arp frame-relay
no frame-relay inverse-arp
frame-relay lmi-type cisco
no shutdown
!
interface Serial0/1/0.25 point-to-point
ip address 150.50.25.1 255.255.255.252
frame-relay interface-dlci 502
R6
interface Serial0/1/0
no ip address
encapsulation frame-relay
serial restart-delay 0
no arp frame-relay
no frame-relay inverse-arp
frame-relay lmi-type cisco
no shutdown
!
interface Serial0/1/0.26 point-to-point
ip address 150.50.26.1 255.255.255.252
frame-relay interface-dlci 602
From:
[email protected]<mailto:[email protected]>
[mailto:[email protected]<mailto:[email protected]>]
On Behalf Of Amer Mustafa
Sent: Saturday, October 23, 2010 3:10 PM
To: [email protected]<mailto:[email protected]>
Subject: [OSL | CCIE_RS] Workbook 1 LAB 18.
Workbook 1 LAB 18.
The inital configs of the routers are with FR proper config, which leads that
the FR links are down. i had to configure ( Frame-relay interface DLCI ) on all
the routers. just would like to know if this is not avilable in the initial
configs on purpose ? becuase its not mentioned in the lab to check FR links or
verify them.
thanks
amer
UHS Confidentiality Notice: This e-mail message, including any attachments, is
for the sole use of the intended recipient(s) and may contain confidential and
privileged information. Any unauthorized review, use, disclosure or
distribution of this information is prohibited, and may be punishable by law.
If this was sent to you in error, please notify the sender by reply e-mail and
destroy all copies of the original message.
UHS Confidentiality Notice: This e-mail message, including any attachments, is
for the sole use of the intended recipient (s) and may contain confidential and
privileged information. Any unauthorized review, use, disclosure or
distribution of this information is prohibited. If this was sent to you in
error, please notify the sender by reply e-mail and destroy all copies of the
original message.
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
