I had same issues with some of the labs on R4 and R2. Its also depend on what POD you are. Actually its OK to trouble shoot frame-relay only thing is you have spend you important time to resolve it. May be helpful to improve trouble shooting skill.
Nilesh 2010/10/24 Magnus Påhlsson <[email protected]> > I see this on at least one router in every IPX lab I do using > proctorlabs. DLCI missing on at least one point-to-point subint... I'm > not entirely sure which exact labs I've seen it on but at least on all > the QoS and MPLS related labs. I did those today so it's fresh in my > memory. > > I've also seen it on at least 3+ different pods. > > On Sun, Oct 24, 2010 at 1:15 AM, Amer Mustafa <[email protected]> > wrote: > > Steve / IP EXPERT team. > > > > Yup, again the same issue between the R2 and R5 FR clould, no > Interface-dlci > > on R2 and the interface was also down. > > > > > > Regards ... > > > > On Sun, Oct 24, 2010 at 1:30 AM, Di Bias, Steve <[email protected] > > > > wrote: > >> > >> OK sorry, I didn’t realize you were in the proctorlabs environment. If > >> you don’t hear back from Marko or Tyson I would notify support on this > >> because it can take away valuable lab time!! > >> > >> > >> > >> From: Amer Mustafa [mailto:[email protected]] > >> Sent: Saturday, October 23, 2010 3:28 PM > >> To: Di Bias, Steve > >> Cc: [email protected] > >> Subject: Re: [OSL | CCIE_RS] Workbook 1 LAB 18. > >> > >> > >> > >> Steve, > >> > >> > >> > >> They were down because there was no DLCI assigned in the sub-interfaces > ( > >> all routes ), You are right with the config below, this is exact same > >> avilable on ipexpert site for manual configuration on the routers. > >> > >> > >> > >> But i guess when you load the configs through script on proctorlabs they > >> come up without frame-relay interface-dlci assigned. > >> > >> > >> > >> > >> > >> regards ... > >> > >> Amer > >> > >> > >> > >> On Sun, Oct 24, 2010 at 1:20 AM, Di Bias, Steve < > [email protected]> > >> wrote: > >> > >> Can you be more specific? Why were they “down”? There was no DLCI’s > >> configured? The wrong DLCI’s were configured? The wrong LMI type? > >> > >> > >> > >> I just looked at the initials configs for VOL1 LAB18 and everything is > >> configured just fine > >> > >> > >> > >> R2 > >> > >> > >> > >> interface Serial0/1/0 > >> > >> no ip address > >> > >> encapsulation frame-relay > >> > >> no arp frame-relay > >> > >> no frame-relay inverse-arp > >> > >> frame-relay lmi-type cisco > >> > >> no shutdown > >> > >> ! > >> > >> interface Serial0/1/0.24 point-to-point > >> > >> ip address 150.50.24.2 255.255.255.252 > >> > >> frame-relay interface-dlci 204 > >> > >> ! > >> > >> interface Serial0/1/0.25 point-to-point > >> > >> ip address 150.50.25.2 255.255.255.252 > >> > >> frame-relay interface-dlci 205 > >> > >> ! > >> > >> interface Serial0/1/0.26 point-to-point > >> > >> ip address 150.50.26.2 255.255.255.252 > >> > >> frame-relay interface-dlci 206 > >> > >> > >> > >> R4 > >> > >> > >> > >> interface Serial0/0/0 > >> > >> no ip address > >> > >> encapsulation frame-relay > >> > >> no arp frame-relay > >> > >> no frame-relay inverse-arp > >> > >> frame-relay lmi-type cisco > >> > >> no shutdown > >> > >> ! > >> > >> interface Serial0/0/0.24 point-to-point > >> > >> ip address 150.50.24.1 255.255.255.252 > >> > >> frame-relay interface-dlci 402 > >> > >> > >> > >> R5 > >> > >> > >> > >> interface Serial0/1/0 > >> > >> no ip address > >> > >> encapsulation frame-relay > >> > >> no arp frame-relay > >> > >> no frame-relay inverse-arp > >> > >> frame-relay lmi-type cisco > >> > >> no shutdown > >> > >> ! > >> > >> interface Serial0/1/0.25 point-to-point > >> > >> ip address 150.50.25.1 255.255.255.252 > >> > >> frame-relay interface-dlci 502 > >> > >> > >> > >> R6 > >> > >> > >> > >> interface Serial0/1/0 > >> > >> no ip address > >> > >> encapsulation frame-relay > >> > >> serial restart-delay 0 > >> > >> no arp frame-relay > >> > >> no frame-relay inverse-arp > >> > >> frame-relay lmi-type cisco > >> > >> no shutdown > >> > >> ! > >> > >> interface Serial0/1/0.26 point-to-point > >> > >> ip address 150.50.26.1 255.255.255.252 > >> > >> frame-relay interface-dlci 602 > >> > >> > >> > >> > >> > >> > >> > >> > >> > >> > >> > >> From: [email protected] > >> [mailto:[email protected]] On Behalf Of Amer Mustafa > >> Sent: Saturday, October 23, 2010 3:10 PM > >> To: [email protected] > >> Subject: [OSL | CCIE_RS] Workbook 1 LAB 18. > >> > >> > >> > >> Workbook 1 LAB 18. > >> > >> > >> > >> The inital configs of the routers are with FR proper config, which leads > >> that the FR links are down. i had to configure ( Frame-relay interface > DLCI > >> ) on all the routers. just would like to know if this is not avilable in > the > >> initial configs on purpose ? becuase its not mentioned in the lab to > check > >> FR links or verify them. > >> > >> > >> > >> > >> > >> thanks > >> > >> amer > >> > >> > >> UHS Confidentiality Notice: This e-mail message, including any > >> attachments, is for the sole use of the intended recipient(s) and may > >> contain confidential and privileged information. Any unauthorized > review, > >> use, disclosure or distribution of this information is prohibited, and > may > >> be punishable by law. If this was sent to you in error, please notify > the > >> sender by reply e-mail and destroy all copies of the original message. > >> > >> > >> > >> > >> UHS Confidentiality Notice: This e-mail message, including any > >> attachments, is for the sole use of the intended recipient(s) and may > >> contain confidential and privileged information. Any unauthorized > review, > >> use, disclosure or distribution of this information is prohibited, and > may > >> be punishable by law. If this was sent to you in error, please notify > the > >> sender by reply e-mail and destroy all copies of the original message. > > > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, please > > visit www.ipexpert.com > > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
