Nope, destination port is a regular gigE port. 12.2(33)SXH1 on a 6500/720.
-- William S. Duncanson [EMAIL PROTECTED] > -----Original Message----- > From: Christian Koch [mailto:[EMAIL PROTECTED] > Sent: Wednesday, June 25, 2008 22:10 > To: William S. Duncanson > Cc: cisco-nsp@puck.nether.net > Subject: Re: [c-nsp] monitor session on a LACP port channel? > > heh, what code/platform are you running? > > the destination port is not included in ether channel is it? > > > On Wed, Jun 25, 2008 at 7:56 PM, William S. Duncanson > <[EMAIL PROTECTED]> wrote: > > > Yeah, I actually left that bit out of the e-mail. > > houcore5(config)#monitor session 1 source interface po16C ? > % Unrecognized command > houcore5(config)#monitor session 1 source interface po16C both > ^ > % Invalid input detected at '^' marker. > > "houcore5(config)#monitor session 1 source interface po16 both" works, > but doesn't result in traffic. > > > -- > > William S. Duncanson > [EMAIL PROTECTED] > > > > > -----Original Message----- > > From: Christian Koch [mailto:[EMAIL PROTECTED] > > Sent: Wednesday, June 25, 2008 21:53 > > To: William S. Duncanson > > Cc: cisco-nsp@puck.nether.net > > Subject: Re: [c-nsp] monitor session on a LACP port channel? > > > > did you specify tx/rx or both on the source port channel? > > > > monitor session 1 source interface port-channel 1 rx(or tx or both) > > > > > > > > > > On Wed, Jun 25, 2008 at 2:16 PM, William S. Duncanson > > <[EMAIL PROTECTED]> wrote: > > > > > > I'm probably missing something really obvious here, but I'm > trying to do > > a > > monitor session on a LACP port channel. sh etherchannel 16 > port-channel > > says the following: > > > > houcore5#sh etherchannel 16 port-channel > > Port-channels in the group: > > ---------------------- > > > > Port-channel: Po16 (Primary Aggregator) > > > > ------------ > > > > Age of the Port-channel = 11d:00h:49m:54s > > Logical slot/port = 14/16 Number of ports = 0 > > HotStandBy port = null > > Port state = Port-channel Ag-Not-Inuse > > Protocol = LACP > > Fast-switchover = disabled > > > > Time since last port bundled: 11d:00h:49m:19s Gi9/18 > > Time since last port Un-bundled: 11d:00h:47m:20s Gi9/18 > > > > Port-channel: Po16C > > ------------ > > > > Age of the Port-channel = 11d:00h:48m:23s > > Logical slot/port = 14/19 Number of ports = 4 > > HotStandBy port = null > > > > Doing a "monitor session 1 source interface po16" yields no > traffic on > > the > > destination port; not surprising, as the interface is marked > down/down. > > Po16C is marked as up/up, but "monitor session 1 source > interface po16C" > > doesn't seem to be acceptable to the command interpreter. What > am I > > doing > > wrong? > > > > > > > > _______________________________________________ > > cisco-nsp mailing list cisco-nsp@puck.nether.net > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > > > > _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/