New line card inserted about a week ago, along with a new 10g service. Last night the LC crashed with the following;
000504: May 17 03:41:24.011 CDT: %CONST_DIAG-SP-3-HM_TEST_FAIL: Module 4 TestMacNotification consecutive failure count:5 000505: May 17 03:41:24.015 CDT: %CONST_DIAG-SP-6-HM_TEST_SP_INFO: TestMacNotification[4]: last_busy_percent[13%], Tx_Rate[577], Rx_Rate[46] 000508: May 17 03:42:17.500 CDT: %LINK-3-UPDOWN: Interface TenGigabitEthernet4/1, changed state to down 000509: May 17 03:42:17.504 CDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet4/1, changed state to down 000510: May 17 03:42:17.628 CDT: %SNMP-5-MODULETRAP: Module 4 [Down] Trap 000511: May 17 03:42:17.476 CDT: %CONST_DIAG-SP-2-HM_LC_CRSH: Module 4 crashed due to unrecoverable errors, Reason: Failed TestFabricCh1Health 000512: May 17 03:42:17.632 CDT: %C6KPWR-SP-4-DISABLED: power to module in slot 4 set off (Diagnostic Failure) 000513: May 17 03:42:17.752 CDT: %LINK-SP-3-UPDOWN: Interface TenGigabitEthernet4/1, changed state to down 000514: May 17 03:42:17.876 CDT: %HA_EM-6-LOG: Mandatory.go_fabrich1.tcl: GOLD EEM TCL policy for TestFabricCh1Health 000515: May 17 03:42:17.756 CDT: %LINEPROTO-SP-5-UPDOWN: Line protocol on Interface TenGigabitEthernet4/1, changed state to down s72033-advipservicesk9_wan-mz.122-33.SXH7.bin sh mod Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1405ACTW 3 16 SFM-capable 16 port 1000mb GBIC WS-X6516-GBIC SAD050603XM 4 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL1338Z6Z2 5 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL SAD084805W5 Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 1 8843.e1b6.f950 to 8843.e1b6.f97f 3.4 12.2(18r)S1 12.2(33)SXH7 Ok 3 0001.63d0.e11e to 0001.63d0.e12d 2.0 6.1(3) 8.7(0.22)BUB Ok 4 0027.0d34.f7bc to 0027.0d34.f7bf 3.0 12.2(14r)S5 12.2(33)SXH7 PwrDown 5 0011.21a1.5680 to 0011.21a1.5683 4.1 8.1(3) 12.2(33)SXH7 Ok Mod Sub-Module Model Serial Hw Status ---- --------------------------- ------------------ ----------- ------- ------- 1 Centralized Forwarding Card WS-F6700-CFC SAL1406AS70 4.1 Ok 4 Distributed Forwarding Card WS-F6700-DFC3BXL SAL1333W4UP 5.5 PwrDown 5 Policy Feature Card 3 WS-F6K-PFC3BXL SAD084806L7 1.4 Ok 5 MSFC3 Daughterboard WS-SUP720 SAD084307B8 2.2 Ok Mod Online Diag Status ---- ------------------- 1 Pass 3 Pass 4 Not Applicable 5 Pass I have read in many earlier threads it could be the SUP the chassis and just a simple reseating of the card. Does anyone have the clear picture here? Thanks so much for looking -- //CL _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/