Dear all:
I am facing some about Cisco Processor Engine: NPE-G1 which was plug into
Cisco 7206VXR . Due some issue i unplug the NPE-G1 card and insert this engine
to another Cisco 7204VXR router at same time i am getting problem while booing
the 7204VXR router and results 7204VXR not come up in normal stage .
Platform: 7204VXR / 7206VXR
Processor Engine: NPE-G1
Flash: 64MB
I got bellow summary message also attached the details log message for better
understanding.it would be nice can any one suggest me how to resolved this
matter.
*** System received a Bus Error exception ***
signal= 0xa, code= 0x1c, context= 0x6101b6b4
PC = 0x60688fe4, SP = 0x61074c30, RA = 0x60688fe4
Cause Reg = 0x0000401c, Status Reg = 0x34008003
System Bootstrap, Version 12.2(8r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
System Bootstrap, Version 12.2(8r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 1048576 Kbytes of main memory
=== Flushing messages () ===
Buffered messages:
Queued messages:
No warm reboot Storage
*** System received a Cache Parity Exception ***
signal= 0x14, code= 0x30000c80, context= 0x64287524
PC = 0xa0000100, SP = 0x646110e0, RA = 0x61d8e9a8
Cause Reg = 0x00004000, Status Reg = 0x3400c107
System Bootstrap, Version 12.2(8r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 1048576 Kbytes of main memory
Thanks for nice co-operation.
regards // Jahangir
*** System received a Bus Error exception ***
signal= 0xa, code= 0x1c, context= 0x6101b6b4
PC = 0x60688fe4, SP = 0x61074c30, RA = 0x60688fe4
Cause Reg = 0x0000401c, Status Reg = 0x34008003
System Bootstrap, Version 12.2(8r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
System Bootstrap, Version 12.2(8r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 1048576 Kbytes of main memory
Self decompressing the image :
###################################################################### [OK]
Self decompressing the image :
####################################################################################################################################################################################################################################################################################################################
[OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 7200 Software (C7200-SPSERVICESK9-M), Version 12.2(33)SRC4,
RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 11-May-09 16:53 by prod_rel_team
Image text-base: 0x60009304, data-base: 0x627635B0
Cache error detected!
CP0_CAUSE (reg 13/0): 0x00004000
CPO_ECC (reg 26/0): 0x40000000
Data cache error
CPO_BUSERRDPA (reg 26/1): 0xFBBFFFE0
CPO_CACHERI (reg 27/0): 0x30000C80
Tag address parity error
Data array parity error
Instruct cache index 0x00000064
CPO_CACHERD (reg 27/1): 0x840000C0
Multiple data cache errors
External cache error
Data cache index 0x00000006
CPO_CCHEDPA (reg 27/3): 0x00020000
: Interrupt exception, CPU signal 20, PC = 0xA0000100
--------------------------------------------------------------------
Possible software fault. Upon recurrence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
-Traceback= 61D8ECCC 61D7D644 60258534 61DAB96C 6018B05C 6018B2B8 6018DC08
60E3D1C8 60E3D524 61D67230 61D6721C
$0 : 00000000, AT : 63F50000, v0 : 1028F4D2, v1 : 0FFFFFD0
a0 : 50003CB4, a1 : 07FFDF88, a2 : 00020002, a3 : 63F724E0
t0 : 63D70000, t1 : 63F72390, t2 : 3400C100, t3 : FFFF00FF
t4 : 6069D058, t5 : 6500B6D8, t6 : 6500B6D4, t7 : 6500B6D0
s0 : 500040C0, s1 : 07FFE18E, s2 : 07FFDF88, s3 : 63F705A8
s4 : 63F700C8, s5 : 00000000, s6 : 000001EE, s7 : 63D70000
t8 : 6460B9F0, t9 : 00000000, k0 : 3040D001, k1 : 00000000
gp : 63F59518, sp : 646110E0, s8 : 0000000E, ra : 61D8E9A8
EPC : 61D8ECCC, ErrorEPC : A0000100, SREG : 3400C107
MDLO : 0037F040, MDHI : 00000000, BadVaddr : 00000008
DATA_START : 0x627635B0
Cause 00004000 (Code 0x0): Interrupt exception
=== Flushing messages () ===
Buffered messages:
Queued messages:
No warm reboot Storage
*** System received a Cache Parity Exception ***
signal= 0x14, code= 0x30000c80, context= 0x64287524
PC = 0xa0000100, SP = 0x646110e0, RA = 0x61d8e9a8
Cause Reg = 0x00004000, Status Reg = 0x3400c107
System Bootstrap, Version 12.2(8r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 1048576 Kbytes of main memory
self decompressing the image :
###################################################################### [OK]
Uncorrectable ECC/Parity Error
Bus Error Status Reg = 0000000081DC0000
Transfer ID = 0x0000
Responder ID = MC
Error Code = Uncorrectable ECC Error in Data
Multiple Errors = No
ZBbus bits 255:192 = 4E6F726D616CC000
ZBbus bits 191:128 = 0005000060F4C880
ZBbus bits 127:64 = 0000004E00400008
ZBbus bits 63:0 = 0000000000000000
System Revision = 8F6F202512500BFF
L2 Read Tag = 0003DD000105FFE0
L2 ECC Tag = 0026DC0090004900
L2 ECC Counter = 0000000000000000
Memory and IO Err Counter = 0000000000000100
Bus Watcher register dump
cor_l2cache_data_ecc_count = 0
bad_l2cache_data_ecc_count = 0
cor_l2cache_tag_ecc_count = 0
bad_l2cache_tag_ecc_count = 0
cor_memory_data_ecc_count = 0
bad_memory_data_ecc_count = 1
bus_errors = 0
%ERR-1-FATAL: Fatal error interrupt, No reloading
err_stat=0x0, err_enable=0xFF, mgmt_event=0x10
System bridge dump:
Bridge 0, for PA Bay 0 (I/O Card, PCMCIA, Interfaces), Handle=0
DEC21150 bridge chip, config=0x0
(0x00):dev, vendor id = 0x00231011
(0x04):status, command = 0x02B00147
(0x08):class code, revid = 0x06040006
(0x0C):hdr, lat timer, cls = 0x00012E10
(0x18):sec lat,cls & bus no = 0x18111000
(0x1C):sec status, io base = 0x22A03101
Received Master Abort on secondary bus
(0x20):mem base & limit = 0x48704000
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16 = 0x00010001
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x02000000
(0x64):serr disable, gpio = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF
Sturgeon LDT Bridge 0, for PA bay 1, 3 and 5, handle=1
AP1011 bridge, config=0x0
(0x00):dev, vendor id = 0x001014D9
(0x04):status, command = 0x00100107
(0x08):class code, revid = 0x06040000
(0x0C):hdr, lat timer, cls = 0x00010010
(0x18):bus id registers = 0x18090403
(0x1C):secondary status = 0x00A09141
(0x20):mem base/limit = 0x4AF04880
(0x30):io upper limit/base = 0x00010001
(0x34):capabilities ptr = 0x00000040
(0x38):expansion rom bar = 0x00000000
(0x3C):bridge ctrl = 0x00230000
(0x40):LDT cmd, cap id, = 0x00210008
(0x44):Link config/control 0 = 0x00000020
(0x48):Link config/control 1 = 0x00000020
(0x4C):LDT revision id = 0x00000011
(0x60):PCI control, read = 0x2F000327
(0x64):Error control = 0x00008080
(0x68):LDT error control = 0x00000A49
(0x6C):Tx ctrl, databufalloc = 0x00041515
(0x70):Link impedance ctrl 0 = 0x7D3C0000
(0x74):Link impedance ctrl 1 = 0x94FE0000
(0xC8):Tx buffer count max 0 = 0x00FFFFFF
(0xCC):Tx buffer count max 1 = 0x00FFFFFF
(0xD4):Debug = 0x03CB089F
(0xD8):AP1011 Diagnostics = 0x00000010
(0xDC):Link 0 rx CRC expected = 0x4916E0A0
(0xF0):Link 0 rx CRC received = 0x95412108
(0xF4):Link 1 rx CRC expected = 0xD5614021
(0xF8):Link 1 rx CRC received = 0x122217A5
Sturgeon LDT Bridge 1, for PA bay 2, 4 and 6, handle=2
AP1011 bridge, config=0x0
(0x00):dev, vendor id = 0x001014D9
(0x04):status, command = 0x00100107
(0x08):class code, revid = 0x06040000
(0x0C):hdr, lat timer, cls = 0x00010010
(0x18):bus id registers = 0x180F0A03
(0x1C):secondary status = 0x00A0F1A1
(0x20):mem base/limit = 0x4FF04D00
(0x30):io upper limit/base = 0x00010001
(0x34):capabilities ptr = 0x00000040
(0x38):expansion rom bar = 0x00000000
(0x3C):bridge ctrl = 0x00230000
(0x40):LDT cmd, cap id, = 0x00220008
(0x44):Link config/control 0 = 0x00000020
(0x48):Link config/control 1 = 0x000000C0
(0x4C):LDT revision id = 0x00000011
(0x60):PCI control, read = 0x2F000327
(0x64):Error control = 0x00008080
(0x68):LDT error control = 0x00000A49
(0x6C):Tx ctrl, databufalloc = 0x00041515
(0x70):Link impedance ctrl 0 = 0x94FE0000
(0x74):Link impedance ctrl 1 = 0x07C00000
(0xC8):Tx buffer count max 0 = 0x00FFFFFF
(0xCC):Tx buffer count max 1 = 0x00FFFFFF
(0xD4):Debug = 0x03CB089F
(0xD8):AP1011 Diagnostics = 0x00000010
(0xDC):Link 0 rx CRC expected = 0x6956E432
(0xF0):Link 0 rx CRC received = 0xDC3BEAD4
(0xF4):Link 1 rx CRC expected = 0x82E4A580
(0xF8):Link 1 rx CRC received = 0xC552AAE2
PA bridge dump:
Unexpected exception, CPU signal 10, PC = 0x0
-Traceback= 0 60522B24 60522A28 60521374 60505F30 605F6A0C 606664E0 605FB450
$0 : 00000000, AT : 60EF0000, v0 : 00000000, v1 : 00000040
a0 : 61074BF8, a1 : FFFFFFFF, a2 : 61074B84, a3 : FFFFFFFF
t0 : 00000000, t1 : 00000000, t2 : 00000000, t3 : 00000000
t4 : 605FB510, t5 : 00000000, t6 : 08000000, t7 : 00000000
s0 : 61074AD0, s1 : 61074BF8, s2 : 61074B84, s3 : 00000000
s4 : 00000000, s5 : FFFFFFFF, s6 : 7FFFFFFF, s7 : FFFFFFFD
t8 : 00000000, t9 : 00000001, k0 : 00000020, k1 : 00000000
gp : 60EF2C40, sp : 61074AA8, s8 : FFFFFFFF, ra : 60522B24
EPC : 00000000, ErrorEPC : BFC01B50, SREG : 34008003
MDLO : 00000000, MDHI : 0000000C, BadVaddr : 00000000
Cause 00000008 (Code 0x2): TLB (load or instruction fetch) exception
Unexpected exception, CPU signal 10, PC = 0x0
-Traceback= 0 60522B24 60522A28 60521374 60525BA0 605F6624 605F5CE0 605F5E4C
60602FA4 6060216C 60602F88 6060216C 605F9650
$0 : 00000000, AT : 00000008, v0 : 00000000, v1 : 00000040
a0 : 60EA7F30, a1 : FFFFFFFF, a2 : 60EA7EBC, a3 : FFFFFFFF
t0 : 00000000, t1 : 00000000, t2 : 00000000, t3 : 00000000
t4 : 00000000, t5 : 00000000, t6 : 0000000C, t7 : 00000000
s0 : 60EA7E08, s1 : 60EA7F30, s2 : 60EA7EBC, s3 : 00000000
s4 : 00000000, s5 : FFFFFFFF, s6 : 7FFFFFFF, s7 : 0000000A
t8 : 00000000, t9 : 00000001, k0 : 61019530, k1 : 00000028
gp : 60EF2C40, sp : 60EA7DE0, s8 : FFFFFFFF, ra : 60522B24
EPC : 00000000, ErrorEPC : BFC01B50, SREG : 34008003
MDLO : 00000000, MDHI : 00000008, BadVaddr : 00000000
Cause 00000008 (Code 0x2): TLB (load or instruction fetch) exception
Nested write_crashinfo call (2 times)
Unexpected exception, CPU signal 10, PC = 0x0
-Traceback= 0 605F5D54 605F5E4C 60602FA4 6060216C 60602F88 6060216C 605F9650
$0 : 00000000, AT : 00000008, v0 : 61000000, v1 : 00000000
a0 : 00000002, a1 : 0000000A, a2 : 00000000, a3 : 0000002D
t0 : 00000001, t1 : 00000000, t2 : 00000000, t3 : 00000000
t4 : 60C09178, t5 : 00000008, t6 : 00000000, t7 : 00000000
s0 : 00000008, s1 : 61020000, s2 : 0000000A, s3 : 00000038
s4 : 61020000, s5 : 60EA0000, s6 : 7FFFFFFF, s7 : 0000000A
t8 : 00000000, t9 : 00000001, k0 : 61019530, k1 : 00000038
gp : 60EF2C40, sp : 60EA7D10, s8 : FFFFFFFF, ra : 605F5D54
EPC : 00000000, ErrorEPC : BFC01B50, SREG : 34008003
MDLO : 00000000, MDHI : 00000002, BadVaddr : 00000000
Cause 00000008 (Code 0x2): TLB (load or instruction fetch) exception
Nested write_crashinfo call (3 times)
*** System received a Bus Error exception ***
signal= 0xa, code= 0x8, context= 0x6101b6b4
PC = 0x00000000, SP = 0x61074aa8, RA = 0x60522b24
Cause Reg = 0x00000008, Status Reg = 0x34008003
System Bootstrap, Version 12.2(8r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 1048576 Kbytes of main memory
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
