# $Id: pnpdump.c,v 1.8 1997/01/14 21:05:35 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
# 
# For details of this file format, see isapnp.conf(5)
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER
#
# Trying port address 0203
# Board 1 has serial identifier c2 00 00 00 04 20 23 54 07

# (DEBUG)
(READPORT 0x0203)
(ISOLATE)
(IDENTIFY *)

# Card 1: (serial identifier c2 00 00 00 04 20 23 54 07)
# AZT2320 Serial No 4 [checksum c2]
# Version 1.0, Vendor version 0.2
# ANSI string -->AZT2320 PnP SOUND DEVICE<--
#
# Logical device id AZT0000
#     Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE AZT2320/4 (LD 0
#     ANSI string -->IDE CDROM DISABLED<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0000
#             Maximum IO base address 0x0000
#             IO base alignment 8 bytes
#             Number of IO addresses required: 0
# (IO 0 (BASE 0x0000))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0000
#             Maximum IO base address 0x0000
#             IO base alignment 2 bytes
#             Number of IO addresses required: 0
# (IO 1 (BASE 0x0000))
#       *** ERROR *** No IRQ specified!

#     End dependent functions
# (ACT Y)
))
#
# Logical device id AZT0001
#     Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE AZT2320/4 (LD 1
#     ANSI string -->AUDIO<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0220
#             IO base alignment 16 bytes
#             Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 1 (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0534
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 2 (BASE 0x0534))
#       IRQ 5.
#             High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 1.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
#       Next DMA channel 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 3))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0240
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
(IO 0 (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
(IO 1 (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0608
#             IO base alignment 212 bytes
#             Number of IO addresses required: 4
#(IO 2 (BASE 0x0534))
#       IRQ 5, 9 or 10.
#             High true, edge sensitive interrupt
(INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
(DMA 0 (CHANNEL 1))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
(DMA 1 (CHANNEL 3))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0240
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 1 (BASE 0x0388))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0e84
#             Maximum IO base address 0x0f44
#             IO base alignment 192 bytes
#             Number of IO addresses required: 4
# (IO 2 (BASE 0x0e84))
#       IRQ 5, 9 or 10.
#             High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x03f0
#             IO base alignment 16 bytes
#             Number of IO addresses required: 16
# (IO 0 (BASE 0x0100))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 1 (BASE 0x0100))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x0ffc
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 2 (BASE 0x0100))
#       IRQ 5, 9, 10, 11 or 15.
#             High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x03f0
#             IO base alignment 16 bytes
#             Number of IO addresses required: 16
# (IO 0 (BASE 0x0100))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 1 (BASE 0x0100))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x0ffc
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 2 (BASE 0x0100))
#       IRQ 5, 9, 10, 11 or 15.
#             High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))

#     End dependent functions
(ACT Y)
))
#
# Logical device id AZT0002
#     Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE AZT2320/4 (LD 2
#     ANSI string -->MPU401 MIDI<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0330
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 0 (BASE 0x0330))
#       IRQ 9.
#             High true, edge sensitive interrupt
# (INT 0 (IRQ 9 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
(IO 0 (BASE 0x0330))
#       IRQ 5, 9, 10, 11 or 15.
#             High true, edge sensitive interrupt
(INT 0 (IRQ 9 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x03fe
#             IO base alignment 2 bytes
#             Number of IO addresses required: 2
# (IO 0 (BASE 0x0100))
#       IRQ 5, 9, 10, 11 or 15.
#             High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))

#     End dependent functions
(ACT Y)
))
#
# Logical device id AZT0003
#     Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE AZT2320/4 (LD 3
#     ANSI string -->GAME PORT<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0200
#             Maximum IO base address 0x0200
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x0200))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x0100))

#     End dependent functions
# (ACT Y)
))
#
# Logical device id AZT0004
#     Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE AZT2320/4 (LD 4
#     ANSI string -->MODEM DISABLED<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0000
#             Maximum IO base address 0x0000
#             IO base alignment 8 bytes
#             Number of IO addresses required: 0
# (IO 0 (BASE 0x0000))
#       *** ERROR *** No IRQ specified!

#     End dependent functions
# (ACT Y)
))
#
# Logical device id AZT0005
#     Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE AZT2320/4 (LD 5
#     ANSI string -->EEPROM<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x03ff
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
# (IO 0 (BASE 0x0100))

#     End dependent functions
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

