On Wed, 2015-09-09 at 13:16 -0500, Scott Silverman wrote: > Actually, it seems that 00 is good in this case. I asked supermicro > for confirmation on all possessible values but haven't heard back > yet.
Ok, just give it a shot with what's there. If I have to reverse the values, that's just a quick simple change. > I will test, probably tomorrow, and get back to you, thanks! Great! Al > > Scott Silverman | IT | Simplex | 312-360-2444 > > 230 S. LaSalle St., Suite 4-100, Chicago, IL 60604 > > On Sep 9, 2015 1:12 PM, "Albert Chu" <ch...@llnl.gov> wrote: > That's not too far removed from the other motherboard. From > ipmi-oem's > comments: > > /* Supermicro OEM > * From Supermicro Engineer > * > * Request > * > * 0x06 - network function > * 0x52 - cmd (master read/write) > * 0x07 - (channel = 0, bus id = 3, bus type = private) > * 0x?? - slave address > * - 0x70 - ps 1 > * - 0x72 - ps 2 > * - 0x74 - ps 3 > * 0x01 - read count > * 0x0c - data to write ... no idea why 0x0c > * > * Response > * > * 0x52 - cmd > * 0x?? - Completion Code > * 0x?? - 0x01 - good > * - 0x00 - bad > */ > > I added yours into a branch of FreeIPMI if you could give it a > shot. I > just assumed the good vs bad response was the same. > > svn co > > http://svn.savannah.gnu.org/svn/freeipmi/branches/supermicroipmioempower > freeipmi > cd freeipmi > ./autogen.sh > ./configure > make > ipmi-oem/ipmi-oem supermicro get-power-supply-status2 1 > ipmi-oem/ipmi-oem supermicro get-power-supply-status2 2 > > As an aside, after I realized that this was going through the > master > read/write and not some arbitrary Supermicro OEM command, I > actually can > add an error message for the 83h error code you saw before. > So > hopefully that's taken care of when you run the original. I > get > > # ipmi-oem/ipmi-oem Supermicro get-power-supply-status 1 > Supermicro:get-power-supply-status failed: NAK on Write > > Al > > On Wed, 2015-09-09 at 12:09 -0500, Scott Silverman wrote: > > I assume that was the case. If it helps, I have the > following from > > SuperMicro (can only confirm for the listed board, I don't > have any > > other X10 to test on): > > > > > > For the X10DRU-i+, please try the command below: > > > > raw 0x06 0x52 0x07 0xb0 0x01 0x0c for power supply 1 > > > > raw 0x06 0x52 0x07 0xb2 0x01 0x0c for power supply 2 > > > > > > > > > > > > > > > > > > > > > > > > Thanks, > > > > > > Scott Silverman | IT | Simplex | 312-360-2444 > > 230 S. LaSalle St., Suite 4-100, Chicago, IL 60604 > > > > On Tue, Sep 8, 2015 at 12:21 PM, Albert Chu <ch...@llnl.gov> > wrote: > > Hi Scott, > > > > Thanks for the report. Unfortunately, since this is > a > > Supermicro > > specific error, not much we can do except wait for a > potential > > update of > > information from Supermicro. I can ping some > Supermicro folks > > and see > > if they can help. > > > > Al > > > > On Fri, 2015-09-04 at 11:18 -0500, Scott Silverman > wrote: > > > Running the ipmi-oem supermicro > > get-(pmbus-)power-supply-status > > > commands against newer (X10 based) SuperMicro > servers > > results in the > > > following error: > > > > > > > > > > > > supermicro:get-pmbus-power-supply-status failed: > No error > > message > > > found for command 52h, network function 06h, and > completion > > code 83h. > > > Please report to <freeipmi-devel@gnu.org> > > > > > > > > > As requested, I'm reporting. > > > > > > > > > I've attached debug output for the regular and the > pmbus > > version. Let > > > me know if there's anything I can do to help > further. > > > > > > > > > > > > > > > Thanks, > > > > > > > > > Scott Silverman | IT | Simplex | 312-360-2444 > > > 230 S. LaSalle St., Suite 4-100, Chicago, IL 60604 > > > > > > > > DISCLAIMER: NOTICE REGARDING PRIVACY AND > CONFIDENTIALITY > > > > > > The information contained in and/or accompanying > this > > communication is > > > intended only for use by the addressee(s) named > herein and > > may contain > > > legally privileged and/or confidential > information. If you > > are not the > > > intended recipient of this e-mail, you are hereby > notified > > that any > > > dissemination, distribution or copying of this > information, > > and any > > > attachments thereto, is strictly prohibited. If > you have > > received this > > > e-mail in error, please immediately notify the > sender and > > permanently > > > delete the original and any copy of any e-mail and > any > > printout > > > thereof. Electronic transmissions cannot be > guaranteed to be > > secure or > > > error-free. The sender therefore does not accept > liability > > for any > > > errors or omissions in the contents of this > message which > > arise as a > > > result of e-mail transmission. Simplex Trading, > LLC and its > > affiliates > > > reserves the right to intercept, monitor, and > retain > > electronic > > > communications to and from its system as permitted > by law. > > Simplex > > > Trading, LLC is a registered Broker Dealer with > CBOE and a > > Member of > > > SIPC. > > > _______________________________________________ > > > Freeipmi-devel mailing list > > > Freeipmi-devel@gnu.org > > > > https://lists.gnu.org/mailman/listinfo/freeipmi-devel > > -- > > Albert Chu > > ch...@llnl.gov > > Computer Scientist > > High Performance Systems Division > > Lawrence Livermore National Laboratory > > > > > > > > > > > > DISCLAIMER: NOTICE REGARDING PRIVACY AND CONFIDENTIALITY > > > > The information contained in and/or accompanying this > communication is > > intended only for use by the addressee(s) named herein and > may contain > > legally privileged and/or confidential information. If you > are not the > > intended recipient of this e-mail, you are hereby notified > that any > > dissemination, distribution or copying of this information, > and any > > attachments thereto, is strictly prohibited. If you have > received this > > e-mail in error, please immediately notify the sender and > permanently > > delete the original and any copy of any e-mail and any > printout > > thereof. Electronic transmissions cannot be guaranteed to be > secure or > > error-free. The sender therefore does not accept liability > for any > > errors or omissions in the contents of this message which > arise as a > > result of e-mail transmission. Simplex Trading, LLC and its > affiliates > > reserves the right to intercept, monitor, and retain > electronic > > communications to and from its system as permitted by law. > Simplex > > Trading, LLC is a registered Broker Dealer with CBOE and a > Member of > > SIPC. > -- > Albert Chu > ch...@llnl.gov > Computer Scientist > High Performance Systems Division > Lawrence Livermore National Laboratory > > > > DISCLAIMER: NOTICE REGARDING PRIVACY AND CONFIDENTIALITY > > The information contained in and/or accompanying this communication is > intended only for use by the addressee(s) named herein and may contain > legally privileged and/or confidential information. If you are not the > intended recipient of this e-mail, you are hereby notified that any > dissemination, distribution or copying of this information, and any > attachments thereto, is strictly prohibited. If you have received this > e-mail in error, please immediately notify the sender and permanently > delete the original and any copy of any e-mail and any printout > thereof. Electronic transmissions cannot be guaranteed to be secure or > error-free. The sender therefore does not accept liability for any > errors or omissions in the contents of this message which arise as a > result of e-mail transmission. Simplex Trading, LLC and its affiliates > reserves the right to intercept, monitor, and retain electronic > communications to and from its system as permitted by law. Simplex > Trading, LLC is a registered Broker Dealer with CBOE and a Member of > SIPC. -- Albert Chu ch...@llnl.gov Computer Scientist High Performance Systems Division Lawrence Livermore National Laboratory _______________________________________________ Freeipmi-devel mailing list Freeipmi-devel@gnu.org https://lists.gnu.org/mailman/listinfo/freeipmi-devel
