lvm -- lvm_blk_ioctl: unknown cmd 0x5310 Trying to move old root to /initrd ... failed
The errors themselves are located a few lines apart (line 245 and 250, respectively, in the attached dmesg.txt).
Otherwise, the system boots fine. I've searched and searched for these two errors but haven't been able to locate and information about /why/ they occur or how to correct them.
Any information regarding these errors is appreciated.
Tom
Linux version 2.4.20-gentoo-r6 ([EMAIL PROTECTED]) (gcc version 3.2.3 20030422 (Gentoo
Linux 1.4 3.2.3-r1, propolice)) #1 Wed Dec 17 08:18:47 MST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001f7f0000 (usable)
BIOS-e820: 000000001f7f0000 - 000000001f7f3000 (ACPI NVS)
BIOS-e820: 000000001f7f3000 - 000000001f800000 (ACPI data)
BIOS-e820: 000000001f800000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
503MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 129008
zone(0): 4096 pages.
zone(1): 124912 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 GBT ) @ 0x000f6590
ACPI: RSDT (v001 GBT AWRDACPI 16944.11825) @ 0x1f7f3000
ACPI: FADT (v001 GBT AWRDACPI 16944.11825) @ 0x1f7f3040
ACPI: MADT (v001 GBT AWRDACPI 16944.11825) @ 0x1f7f6a00
ACPI: DSDT (v001 GBT AWRDACPI 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
Kernel command line: root=/dev/vg/root
Initializing CPU#0
Detected 2411.733 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4810.34 BogoMIPS
Memory: 502960k/516032k available (1688k kernel code, 10508k reserved, -2064k data,
108k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
Proc Config support by [EMAIL PROTECTED]
proc config counted 3963 bytes in names
proc config counted 438 bytes in value handles
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20021122
PCI: PCI BIOS revision 2.10 entry at 0xf9d80, last bus=1
PCI: Using configuration type 1
ACPI-0511: *** Info: GPE Block0 defined as GPE0 to GPE31
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15, disabled)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.10e
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller on PCI bus 00 dev f9
PCI: Device 00:1f.1 not available because of resource collisions
ICH4: BIOS setup was incomplete.
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
hda: WDC AC418000D, ATA DISK drive
hdb: WDC AC418000D, ATA DISK drive
hdc: CDU5211, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 35239680 sectors (18043 MB) w/1966KiB Cache, CHS=2193/255/63
hdb: 35239680 sectors (18043 MB) w/1966KiB Cache, CHS=2193/255/63
hdc: ATAPI 52X CD-ROM drive, 120kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2
/dev/ide/host0/bus0/target1/lun0: p1 p2
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xe0018000, 00:40:95:0a:92:0a, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
eth1: RealTek RTL8139 Fast Ethernet at 0xe001a000, 00:20:ed:85:52:9d, IRQ 5
eth1: Identified 8139 chip type 'RTL-8139C'
Equalizer1996: $Revision: 1.2.1 $ $Date: 1996/09/22 13:52:00 $ Simon Janes ([EMAIL
PROTECTED])
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 2828.800 MB/sec
32regs : 1776.000 MB/sec
pIII_sse : 3149.600 MB/sec
pII_mmx : 2834.400 MB/sec
p5_mmx : 2856.000 MB/sec
raid5: using function: pIII_sse (3149.600 MB/sec)
md: multipath personality registered as nr 7
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
[events: 00000047]
[events: 00000039]
[events: 00000047]
[events: 00000039]
md: autorun ...
md: considering ide/host0/bus0/target1/lun0/part2 ...
md: adding ide/host0/bus0/target1/lun0/part2 ...
md: adding ide/host0/bus0/target0/lun0/part2 ...
md: created md1
md: bind<ide/host0/bus0/target0/lun0/part2,1>
md: bind<ide/host0/bus0/target1/lun0/part2,2>
md: running: <ide/host0/bus0/target1/lun0/part2><ide/host0/bus0/target0/lun0/part2>
md: ide/host0/bus0/target1/lun0/part2's event counter: 00000039
md: ide/host0/bus0/target0/lun0/part2's event counter: 00000039
md1: max total readahead window set to 496k
md1: 2 data-disks, max readahead per data-disk: 248k
raid0: looking at ide/host0/bus0/target0/lun0/part2
raid0: comparing ide/host0/bus0/target0/lun0/part2(17510784) with
ide/host0/bus0/target0/lun0/part2(17510784)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at ide/host0/bus0/target1/lun0/part2
raid0: comparing ide/host0/bus0/target1/lun0/part2(17510784) with
ide/host0/bus0/target0/lun0/part2(17510784)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: zone 0
raid0: checking ide/host0/bus0/target0/lun0/part2 ... contained as device 0
(17510784) is smallest!.
raid0: checking ide/host0/bus0/target1/lun0/part2 ... contained as device 1
raid0: zone->nb_dev: 2, size: 35021568
raid0: current zone offset: 17510784
raid0: done.
raid0 : md_size is 35021568 blocks.
raid0 : conf->smallest->size is 35021568 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: updating md1 RAID superblock on device
md: ide/host0/bus0/target1/lun0/part2 [events: 0000003a]<6>(write)
ide/host0/bus0/target1/lun0/part2's sb offset: 17510784
md: ide/host0/bus0/target0/lun0/part2 [events: 0000003a]<6>(write)
ide/host0/bus0/target0/lun0/part2's sb offset: 17510784
md: considering ide/host0/bus0/target1/lun0/part1 ...
md: adding ide/host0/bus0/target1/lun0/part1 ...
md: adding ide/host0/bus0/target0/lun0/part1 ...
md: created md0
md: bind<ide/host0/bus0/target0/lun0/part1,1>
md: bind<ide/host0/bus0/target1/lun0/part1,2>
md: running: <ide/host0/bus0/target1/lun0/part1><ide/host0/bus0/target0/lun0/part1>
md: ide/host0/bus0/target1/lun0/part1's event counter: 00000047
md: ide/host0/bus0/target0/lun0/part1's event counter: 00000047
md: RAID level 1 does not need chunksize! Continuing anyway.
md0: max total readahead window set to 124k
md0: 1 data-disks, max readahead per data-disk: 124k
raid1: device ide/host0/bus0/target1/lun0/part1 operational as mirror 1
raid1: device ide/host0/bus0/target0/lun0/part1 operational as mirror 0
raid1: raid set md0 active with 2 out of 2 mirrors
md: updating md0 RAID superblock on device
md: ide/host0/bus0/target1/lun0/part1 [events: 00000048]<6>(write)
ide/host0/bus0/target1/lun0/part1's sb offset: 104320
md: ide/host0/bus0/target0/lun0/part1 [events: 00000048]<6>(write)
ide/host0/bus0/target0/lun0/part1's sb offset: 104320
md: ... autorun DONE.
LVM version 1.0.5+(22/07/2002)
evms: md raid5: measuring checksumming speed
evms: md raid5: 8regs : 2786.400 MB/sec
evms: md raid5: 32regs : 1813.600 MB/sec
evms: md raid5: pIII_sse : 3149.600 MB/sec
evms: md raid5: pII_mmx : 2799.200 MB/sec
evms: md raid5: p5_mmx : 2817.600 MB/sec
evms: md raid5: using function: pIII_sse (3149.600 MB/sec)
evms: EVMS v1.2.1 initializing .... info level(5).
evms: md core: [md0, level=1] raid array is not clean -- starting background
reconstruction
RAID level 1 does not need chunksize! Continuing anyway.
evms: md raid1: device hdb1 operational as mirror 1
evms: md raid1: device hda1 operational as mirror 0
evms: md raid1: raid set md0 not clean; reconstructing mirrors
evms: md raid1: raid set md0 active with 2 out of 2 mirrors
evms: md core: syncing RAID array md0
evms: md core: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
evms: md core: using maximum available idle IO bandwith (but not more than 100000
KB/sec) for reconstruction.
evms: md core: using 124k window, over a total of 104320 blocks.
evms: Exporting EVMS Volume(117,1) from "/dev/evms/md/md0".
evms: Exporting EVMS Volume(117,2) from "/dev/evms/lvm/vg/swap".
evms: Exporting EVMS Volume(117,3) from "/dev/evms/lvm/vg/root".
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1183k freed
VFS: Mounted root (ext2 filesystem).
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 00:1d.7 to 64
hcd.c: ehci-hcd @ 00:1d.7, Intel Corp. 82801DB USB EHCI Controller
hcd.c: irq 5, pci mem e003c000
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd.c: restricting 64bit DMA mappings to segment 0 ...
ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0
hub.c: USB hub found
hub.c: 6 ports detected
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Setting latency timer of device 00:1d.0 to 64
uhci.c: USB UHCI at I/O 0xd800, IRQ 9
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
uhci.c: USB UHCI at I/O 0xd000, IRQ 11
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
lvm -- lvm_blk_ioctl: unknown cmd 0x5310
reiserfs: checking transaction log (device 3a:01) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 108k freed
Adding Swap: 524280k swap-space (priority -1)
Intel 810 + AC97 Audio, version 0.24, 08:28:30 Dec 17 2003
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH4 found at IO 0xe400 and 0xe000, MEM 0xea081000 and 0xea082000, IRQ 11
i810: Intel ICH4 mmio at 0xe0156000 and 0xe0158000
i810_audio: Primary codec has ID 2
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 2
ac97_codec: AC97 Audio codec, id: ALG32(ALC650)
i810_audio: AC'97 codec 2, new EID value = 0x05c7
i810_audio: AC'97 codec 2, DAC map configured, total channels = 6
eth0: Setting 100mbps half-duplex based on auto-negotiated partner ability 40a1.
eth0: no IPv6 routers present
evms: md core: md0: sync done.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,0), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,0), internal journal
EXT3-fs: mounted filesystem with ordered data mode.-- [EMAIL PROTECTED] mailing list
