Hi Paula,

I am in agreement with everyone else about putting the processor on a delay so 
it will finish when needed. However, if that is not possible, it is perfectly 
fine for the blocks to harden at room temp, not freezing, and then be warmed up 
again for embedding. This has come up in my research lab, and we haven't had 
any problems.

Regards,
Lori

This message has been marked as Medtronic Controlled
-----Original Message-----
From: P Sicurello via Histonet [mailto:histonet@lists.utsouthwestern.edu]
Sent: Tuesday, May 16, 2017 11:30 AM
To: Logan, Shannon <shannon.lo...@bellin.org>
Cc: histonet@lists.utsouthwestern.edu
Subject: Re: [Histonet] A Question About Paraffin Times

Hi Shannon and Everyone Else,

Usually the samples are placed on a weekend delay.  This time, however, the 
breast cases were sitting in formalin since Thursday and the run had to end on 
Saturday due to the CAP 72 hour rule for breast and HER2 testing.

The problem is, the person in charge of Histology not a Histologist.  The 
person in charge was told by several experienced histotechs that letting the 
samples sit in molten paraffin is not a good thing to do.  They were told that 
it was routine (which it isn't) to let them sit in hot wax for days.

I just need information that states that sitting in paraffin for any excessive 
length of time is bad.  I found it mentioned in Sheehan and Hrapcek's "Theory 
and Practice of Histotechnology".

I can't find my Carson.  Does she mention excessive times in paraffin?

If so, please let me know.

Thank you for all the assistance.

Sincerely,

Paula Sicurello, HTL (ASCP)CM

Histotechnology Specialist

UC San Diego Health

200 Arbor Drive

San Diego, CA 92103

(P): 619-543-2872 <#>



*Confidentiality Notice*: The information transmitted in this e-mail is 
intended only for the person or entity to which it is addressed and may contain 
confidential and/or privileged material.  Any review, retransmission, 
dissemination or other use of or taking of any action in reliance upon this 
information by persons or entities other than the intended recipient is 
prohibited.  If you received this e-mail in error, please contact the sender 
and delete the material from any computer.

On Tue, May 16, 2017 at 11:13 AM, Logan, Shannon <shannon.lo...@bellin.org>
wrote:

> Hello Paula,
>
> So why must the cassettes be removed on Saturday morning if you aren’t
> embedding until Monday morning?
>
> Don’t you have a “delay start” feature on your processor? Neither
> option A or B seem like a good thing for the tissue!
>
>  We time our processor to finish at 5 AM Monday when the first
> Histotech arrives for embedding.
>
> The cassettes remain in formalin until the processor starts up on
> Sunday evening.
>
>
>
> Regards,
>
>
>
>
>
> Shannon H. Logan  B.S., HTL (ASCP)
>
> Pathology Department
>
>
>
> Bellin Health Memorial Hospital
>
> 744 South Webster Avenue
>
> Green Bay, WI 54305-3400
>
> 920-433-3653  X3727 <(920)%20433-3653>
>
>
>
>
>
>
>
> *From:* P Sicurello via Histonet
> [mailto:histonet@lists.utsouthwestern.edu]
>
> *Sent:* Tuesday, May 16, 2017 10:34 AM
> *To:* HistoNet
> *Subject:* [Histonet] A Question About Paraffin Times
>
>
>
> Good Morning Listers,
>
> I am asking the collective wisdom of the Histonet this question:
>
>
> Is it better to remove baskets from the processor on Saturday morning and:
>
> A. Let the cassettes freeze, then melt them down and embed Monday morning?
> OR
> B. Leave the cassettes in molten paraffin and embed Monday morning?
>
>
> I am of the opinion that leaving the samples (not fatty, like breast
> cores) in molten paraffin (62 degrees C) is bad practice, and causes
> them to get "crunchy", among other things.
>
> What do you think?
>
> Thank in advance.
>
> Sincerely,
>
> Paula Sicurello, HTL (ASCP)CM
>
> Histotechnology Specialist
>
> UC San Diego Health
>
> 200 Arbor Drive
>
> San Diego, CA 92103
>
> (P): 619-543-2872 <(619)%20543-2872> <#>
>
>
>
> *Confidentiality Notice*: The information transmitted in this e-mail
> is intended only for the person or entity to which it is addressed and
> may contain confidential and/or privileged material. Any review,
> retransmission, dissemination or other use of or taking of any action
> in reliance upon this information by persons or entities other than
> the intended recipient is prohibited. If you received this e-mail in
> error, please contact the sender and delete the material from any computer.
> _______________________________________________
> Histonet mailing list
> Histonet@lists.utsouthwestern.edu
> http://lists.utsouthwestern.edu/mailman/listinfo/histonet
>
_______________________________________________
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet
[CONFIDENTIALITY AND PRIVACY NOTICE] Information transmitted by this email is 
proprietary to Medtronic and is intended for use only by the individual or 
entity to which it is addressed, and may contain information that is private, 
privileged, confidential or exempt from disclosure under applicable law. If you 
are not the intended recipient or it appears that this mail has been forwarded 
to you without proper authority, you are notified that any use or dissemination 
of this information in any manner is strictly prohibited. In such cases, please 
delete this mail from your records. To view this notice in other languages you 
can either select the following link or manually copy and paste the link into 
the address bar of a web browser: http://emaildisclaimer.medtronic.com
_______________________________________________
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet

Reply via email to