Hello Everyone, It would work then die. I recreated the VSE Utility tape and everything is work again.
Ed Martin 330-588-4723 ext 40441 -----Original Message----- From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of Kris Buelens Sent: Tuesday, June 17, 2008 3:25 PM To: IBMVM@LISTSERV.UARK.EDU Subject: Re: IPL from TAPE of VSE utiltiy tape > HCPGIR450W CP entered; disabled wait PSW 000A0000 00001122 the 1122 is not a VM wait state. CP is just being friendly: HCPGIR450W is isseud to tell you: the program in your virtual machine has committed suicide (i.e. it loaded a PSW from which it never can never wake up). If the program running in the virtual machine is CP itself (or a VM tool), yes, then the PSW holds a wait code, that you can interrogate with HELP HCPnnnnW In your case, you tell it is a VSE tool: consult the VSE documents. If things didn't change since I touched VSE: VSE stores a wait code somewhere in low core. 2008/6/17 Bill Munson <[EMAIL PROTECTED]>: > You might try attaching your tape drive as 181 > att 582 * 181 > Your VSE system might be trying to use an address of 582 > > Bill Munson > VM System Programmer > 201-418-7588 > > President MVMUA > http://www2.marist.edu/~mvmua/ > > > > > > "Edward M. Martin" <[EMAIL PROTECTED]> > Sent by: The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> > 06/17/2008 02:46 PM > Please respond to > The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> > > > To > IBMVM@LISTSERV.UARK.EDU > cc > > Subject > IPL from TAPE of VSE utiltiy tape > > > > > > > Hello Everyone, > I am trying to ipl from 582 tape drive using a VSE/ESA Standalone > Utility tape. > Everything starts to work and bam. > HCPGIR450W CP entered; disabled wait PSW 000A0000 00001122 > I have attached the tape to my z/VM user id. > Any thing I should look for? > Terminal Conmode 3270 3270 mode > Def 009 01f just to make sure > Ipl 582 clear > Wait and hit enter. > > Console appears, then after about 3-5 seconds. > HCPGIR450W CP entered; disabled wait PSW 000A0000 00001122 > > HCP1122E command was not performed. Tape vdev has been given to user > userid. > > Explanation: The command could not be performed because you are no longer > the > owner of the real device associated with the virtual device specified as > vdev. > This occurs when you have issued the GIVE command with the RETURN option > for > this device. command may be either IPL, REWIND, or RESET. > > System Action: The command is not performed, and system operation > continues. > > User Response: You will not be able to issue this command to this virtual > > device until the current owner of the device detaches it. > > Ed Martin > 330-588-4723 > ext 40441 > > *************************** IMPORTANT > NOTE***************************** The opinions expressed in this > message and/or any attachments are those of the author and not > necessarily those of Brown Brothers Harriman & Co., its > subsidiaries and affiliates ("BBH"). There is no guarantee that > this message is either private or confidential, and it may have > been altered by unauthorized sources without your or our knowledge. > Nothing in the message is capable or intended to create any legally > binding obligations on either party and it is not intended to > provide legal advice. BBH accepts no responsibility for loss or > damage from its use, including damage from virus. > ************************************************************************ > -- Kris Buelens, IBM Belgium, VM customer support