Yes Marcy is correct about adding P01 to your VSWITCH address. I will have to do something similar on February 13th when we move from a z10 to z196. My plan is to have two SYSTEM CONFIG members. One will be called SYS2817 CONFIG and I will use it to do the first IPL on the new box. That one will have my changes in it. If all goes well I will change SYSTEM CONFIG before the next IPL.
Paul Feller AIT Mainframe Technical Support pfel...@aegonusa.com (319)-355-7824 -----Original Message----- From: The IBM z/VM Operating System [mailto:IBMVM@LISTSERV.UARK.EDU] On Behalf Of Marcy Cortes Sent: Friday, February 04, 2011 3:57 PM To: IBMVM@LISTSERV.UARK.EDU Subject: Re: z196 lb4ul Right, You would redefine it like this define vswitch lnxvsw1 rdev 9004.p01 Or play it safe and put both in there ☺ define vswitch lnxvsw1 rdev 9004.p00 9004.p01 Marcy This message may contain confidential and/or privileged information. If you are not the addressee or authorized to receive this for the addressee, you must not use, copy, disclose, or take any action based on this message or any information herein. If you have received this message in error, please advise the sender immediately by reply e-mail and delete this message. Thank you for your cooperation. From: The IBM z/VM Operating System [mailto:IBMVM@LISTSERV.UARK.EDU] On Behalf Of George Henke/NYLIC Sent: Friday, February 04, 2011 1:53 PM To: IBMVM@LISTSERV.UARK.EDU Subject: Re: [IBMVM] z196 lb4ul Paul, Marcy, et al: I just came from a z196 pre-install planning meeting (by phone) in which it was said that the OSA on the z/196 will be using PORT 1. We are currently using PORT 0 on our Z9. Does this mean our VSWITCH definition (below) in SYSTEM CONFIG which defaults to PORT 0 will not work on the z196 unless we code PORT 1? define vswitch lnxvsw1 rdev 9004 George Henke/NYLIC 02/01/2011 03:40 PM To The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> cc Subject Re: z196 lb4ulLink ty all very much. "Feller, Paul" <pfel...@aegonusa.com> Sent by: The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> 02/01/2011 03:24 PM Please respond to The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> To IBMVM@LISTSERV.UARK.EDU cc Subject Re: z196 lb4ul You would be using the default which is port 0 (zero). The port number really only comes into play if you have an OSA Express3 card and are connecting to the second port or what is called the A1 port on the card layout. Paul Feller AIT Mainframe Technical Support From: The IBM z/VM Operating System [mailto:IBMVM@LISTSERV.UARK.EDU] On Behalf Of George Henke/NYLIC Sent: Tuesday, February 01, 2011 2:05 PM To: IBMVM@LISTSERV.UARK.EDU Subject: Re: z196 lb4ul What is the default PORT number? We do not specify PORT number in our VSWITCH definition below (from SYSTEM CONFIG): define vswitch lnxvsw1 rdev 9004 Sorry to ask: But does this mean we do not use an OSA.? Or does it mean we use a default? I think it may mean the former. Mark Post <mp...@novell.com> Sent by: The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> 02/01/2011 02:50 PM Please respond to The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> To IBMVM@LISTSERV.UARK.EDU cc Subject Re: z196 lb4ul >>> On 2/1/2011 at 02:45 PM, George Henke/NYLIC <george_he...@newyorklife.com> wrote: > How did you change your vswitch definition for PO1? > > Chuckie has deigned use of PORTNAME in VSWITCH taboo. Port number is not the same as port name. Two different parameters entirely. Mark Post