What does QUERY SHUTDOWNTIME indicate as the amount of time reserved for the control program to shut down? If this value equals or exceeds the time out indicated from the hardware, then CP will begin shutting down immediately upon receiving the shutdown signal, as it believes it doesn't have enough time to allow guests to shut down and cleanly shut down CP.
You can also use QUERY SIGNALS to see which guests are enabled for signals. Those which are not in the list will not receive a shutdown signal. Kevin Adams z/VM CP Development IBM Corporation, Endicott, NY E-mail - kada...@us.ibm.com Extension: 3-5467 T/L: 620-5467 External: 607-429-5467 The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> wrote on 05/24/2011 05:21:11 PM: > From: Tom Huegel <tehue...@gmail.com> > To: IBMVM@LISTSERV.UARK.EDU > Date: 05/24/2011 05:21 PM > Subject: Re: z/VM shutdown > Sent by: The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> > > Marcy - For me 4 to 5 minutes would be plenty of time.. but it > appears I get 0 .. Of course I would normally do a normal z/VM > SHUTDOWN .. but bleep happens, I am just trying to be proactive.. > On Tue, May 24, 2011 at 2:13 PM, Marcy Cortes <marcy.d.cor...@wellsfargo.com > > wrote: > You don’t get the full time if done from the HW. > 4-5 minutes – somewhere around there I believe is what you get. > Could that be what you saw? > It’s not enough to get all of our severs down so we always take them > down outside of the HW/GDPS deactivate. > > > Marcy > From: The IBM z/VM Operating System [mailto:IBMVM@LISTSERV.UARK.EDU] > On Behalf Of Tom Huegel > Sent: Tuesday, May 24, 2011 2:10 PM > > To: IBMVM@LISTSERV.UARK.EDU > Subject: Re: [IBMVM] z/VM shutdown > > Well, this is sort of what I am looking for... > > "A signal can be sent in response to a hardware event, such as a > deactivation of the z/VM image..." > > I have all of the signals etc. set for the guest OSs but when > someone pulled the plug (deactivated) on the HMC to stop my LPAR z/ > VM ended immediatly... OK so maybe this is a hardware question 'how > to delay LPAR activation while z/VM shuts down?'. > On Tue, May 24, 2011 at 1:26 PM, Kevin S Adams <kada...@us.ibm.com> wrote: > Yes, z/VM supports shutdown signals. There is a section titled > Automating a Shutdown in Chapter 7 of z/VM: System Operation which > describes this function. > > Kevin Adams > z/VM CP Development > IBM Corporation, Endicott, NY > E-mail - kada...@us.ibm.com > Extension: 3-5467 > T/L: 620-5467 > External: 607-429-5467 > > > > The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> wrote on 05/ > 24/2011 03:32:59 PM: > > > From: Tom Huegel <tehue...@gmail.com> > > To: IBMVM@LISTSERV.UARK.EDU > > Date: 05/24/2011 03:35 PM > > Subject: z/VM shutdown > > Sent by: The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU> > > > > Sorry if this sounds dumb, but I seem to remember someone talking > > about z/VM (CP) being enabled for SIGNAL SHUTDOWN that it could > > receive from either hardware, or a first level z/VM. But I don't > > seem to be able to find anything like that in my searches. Or is > > that something in a future release? > > > > >