I have found some info about frame-relay CCC and I would imagine the ATM CCC would be similar, but I am a little confused as to which CCC variant of ATM I will need and it can still land one of those PVC's on the m10i doing the switching.
[edit] interfaces { so-1/0/0 { encapsulation <http://www.juniper.net/techpubs/software/junos/junos76/swconfig76-network-interfaces/html/interfaces-summary112.html#2216533> frame-relay-ccc; unit <http://www.juniper.net/techpubs/software/junos/junos76/swconfig76-network-interfaces/html/interfaces-summary421.html#1017673> 1 { point-to-point <http://www.juniper.net/techpubs/software/junos/junos76/swconfig76-network-interfaces/html/interfaces-summary292.html#1016678>; eui-64 <http://www.juniper.net/techpubs/software/junos/junos76/swconfig76-network-interfaces/html/interfaces-summary122.html#1320392> frame-relay-ccc; dlci <http://www.juniper.net/techpubs/software/junos/junos76/swconfig76-network-interfaces/html/interfaces-summary100.html#2083014> 600; } } so-2/0/0 { encapsulation <http://www.juniper.net/techpubs/software/junos/junos76/swconfig76-network-interfaces/html/interfaces-summary112.html#2216533> frame-relay-ccc; unit 2 { point-to-point; encapsulation frame-relay-ccc; dlci <http://www.juniper.net/techpubs/software/junos/junos76/swconfig76-network-interfaces/html/interfaces-summary100.html#2083014> 750; } } } protocols { connections <http://www.juniper.net/techpubs/software/junos/junos76/swconfig76-network-interfaces/html/interfaces-summary75.html#1014816> { interface-switch <http://www.juniper.net/techpubs/software/junos/junos76/swconfig76-network-interfaces/html/interfaces-summary169.html#1015803> router-a-router-c { interface so-1/0/0.1; interface so-2/0/0.2; } } mpls { interface all; } } On Wed, Aug 26, 2009 at 10:42 PM, Clue Store <cluest...@gmail.com> wrote: > Hi List, > > I have a situation where I need to take 3 PVC's that I am getting from a > provider and land one of them on an ATM interface (OC-3) and possibly > cross-connect the others to the second port in the PIC to send to another > router (basically performing an ATM switch functionality). Can this be done > on a "2x OC-3 ATM, SMIR" PIC on a m10i ?? And if so, can someone point me to > some config samples as to how to do this?? I imagine this would be a CCC > on interface, but I am a complete noob when it comes to ATM on the juniper. > Relevent configs of what I need to do are below. > > Current Cisco config... > > interface ATM2/0 > no ip address > ip route-cache flow > load-interval 30 > no atm ilmi-keepalive > ! > interface ATM2/0.1 point-to-point --------------------------> PVC I wish > to terminate on the first OC-3 Port > description ***Internet PVC*** > ip address x.x.x.x 255.255.255.252 > pvc 3/101 > protocol ip x.x.x.x broadcast > ubr 75000 > encapsulation aal5snap > ! > ! > interface ATM2/0.2 point-to-point ----------------------------> 1st PVC > CCC to the second port to connect back to the cisco > description Customer1 T1 #1 > ip address x.x.x.x 255.255.255.252 > pvc 3/102 > protocol ip x.x.x.x broadcast > ubr 75000 > encapsulation aal5snap > ! > ! > interface ATM2/0.3 point-to-point ----------------------------> 2nd PVC > CCC to the second port to connect back to the cisco > description Customer2 T1 #2 > ip address x.x.x.x 255.255.255.252 > pvc 3/103 > protocol ip x.x.x.x broadcast > ubr 10000 > encapsulation aal5snap > > Thx, > Clue > > _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp