Hello, Here, is the information. but the Junipes's don't see each other.
o...@m10_a> show configuration interfaces ge-0/2/0 flexible-vlan-tagging; gigether-options { ethernet-switch-profile { tag-protocol-id 0x88a8; } } unit 50 { vlan-tags outer 0x88a8.50 inner 100; family inet { address 192.168.38.58/30; } } o...@m10_a> show interfaces ge-0/2/0.100 | match Encapsulation o...@m10_ashow interfaces ge-0/2/0 | match Encapsulation Flags: SNMP-Traps VLAN-Tag [ 0x0000.0 ] Encapsulation: ENET2 o...@m5_b> show configuration interfaces ge-0/2/0 flexible-vlan-tagging; gigether-options { ethernet-switch-profile { tag-protocol-id 0x88a8; } } unit 50 { vlan-tags outer 0x88a8.50 inner 100; family inet { address 192.168.38.57/30; } } o...@metism5_b> show interfaces ge-0/2/0.100 | match Encapsulation o...@metism5_b> show interfaces ge-0/2/0 | match Encapsulation Flags: SNMP-Traps VLAN-Tag [ 0x0000.0 ] Encapsulation: ENET2 Summit x450_A# sho vman etherType vman EtherType : 0x88a8 x450_A# # SHO vman "Test_Side_A" VMAN Interface with name Test_Side_A created by user Admin State: Enabled Tagging: 802.1Q Tag 50 Virtual router: VR-Default **Primary IP : 192.168.175.166/28 **(Administration IP address)** IPv6: None STPD: None Protocol: Match all unfiltered protocols Loopback: Disabled NetLogin: Disabled QosProfile: None configured Egress Rate Limit Designated Port: None configured Ports: 4. (Number of active ports=3) Tag: *1(UpLink_x450_B),*46(M10_A_Ge-0/2/0) Flags: (*) Active, (!) Disabled, (g) Load Sharing port (b) Port blocked on the vlan, (a) Authenticated NetLogin port (u) Unauthenticated NetLogin port, (m) Mac-Based port x450_A# x450_B # sh vman etherType Vman Primary EtherType : 0x88a8 x450_B # sho vman "Test_Side_B" VMAN Interface with name Test_Side_B created by user Admin State: Enabled Tagging: 802.1Q Tag 50 Virtual router: VR-Default **Primary IP : 172.16.40.2/24** (Administration IP address)** IPv6: None STPD: None Protocol: Match all unfiltered protocols Loopback: Disabled NetLogin: Disabled QosProfile: None configured Egress Rate Limit Designated Port: None configured Flood Rate Limit QosProfile: None configured Ports: 20. (Number of active ports=15) Tag: *1(UpLink_x450_A),*45(M5_B_Ge-0/2/0) Flags: (*) Active, (!) Disabled, (g) Load Sharing port (b) Port blocked on the vlan, (m) Mac-Based port (a) Egress traffic allowed for NetLogin (u) Egress traffic unallowed for NetLogin x450_B# Best regards. > Date: Tue, 20 Oct 2009 11:15:37 +0300 > From: evge...@ip.datagroup.ua > To: onamru...@hotmail.com > Subject: Re[4]: [j-nsp] Logical Interfaces 802.1ad > > Hi Onam, > I examined you config and at first glance all should works.... > Please show from both Junipers: > show interfaces xxx.100 | match Encapsulation > > From both Summits: > show vman etherType > show vman xxx > > > > best regards, > -- > Evgeniy Aikashev > network engineer > JSC DATAGROUP > > Tuesday, October 20, 2009, 9:45:37 AM, Onam wrote: > > Dear Evgenie, > > > Thaks for your help. > > > But I configure the juniper as you suggest me, but it doesn't work. I don't > > know if I'am missing a parameter or something else. > > > I sent you the topology, maybe you can check it. > > > I just try the same with to Cisco router at the same topology and it works, > > in fact I test it with 0x88a8 and 0x9100. > > > Best regards. > > >> Date: Mon, 19 Oct 2009 10:47:16 +0300 > >> From: evge...@ip.datagroup.ua > >> To: onamru...@hotmail.com > >> CC: juniper-nsp@puck.nether.net > >> Subject: Re[2]: [j-nsp] Logical Interfaces 802.1ad > >> > >> Also works fine: > >> > >> {master}[edit interfaces xe-4/1/0] > >> evge...@mx480# show > >> description "=== Summit X650 test ==="; > >> flexible-vlan-tagging; > >> encapsulation flexible-ethernet-services; > >> gigether-options { > >> ethernet-switch-profile { > >> tag-protocol-id 0x88a8; > >> } > >> } > >> unit 100 { > >> description "=== Summit X650 test ==="; > >> vlan-tags outer 0x88a8.4092 inner 100; > >> family inet { > >> address x.x.x.x/30; > >> } > >> } > >> > >> Summit: > >> enable jumbo-frame ports all > >> > >> > >> best regards, > >> -- > >> Evgeniy Aikashev > >> network engineer > >> JSC DATAGROUP > >> > >> Monday, October 19, 2009, 10:17:22 AM, Onam wrote: > >> > Hello Evgeniy, > >> > >> > I made some test before with this ethertype and it works. The Extreme > >> > x450 use both of them > >> > 0x8100 for VLAN and 0x88a8 for VMAN so if i do that the VMAN will become > >> > a VLAN. > >> > >> > I see that by default the Juniper router M10 use ethertype 0x8100, but > >> > when I try to use > >> > ethertype 0x88a8 the devices doens't see each other, I run a ping to the > >> > other side with no response. > >> > >> > >> >> Date: Mon, 19 Oct 2009 09:58:23 +0300 > >> >> From: evge...@ip.datagroup.ua > >> >> To: onamru...@hotmail.com > >> >> CC: juniper-nsp@puck.nether.net > >> >> Subject: Re: [j-nsp] Logical Interfaces 802.1ad > >> >> > >> >> Hello Onam, > >> >> try to change ethertype from Summit side: > >> >> > >> >> configure vman ethertype 0x8100 > >> >> > >> >> best regards, > >> >> -- > >> >> Evgeniy Aikashev > >> >> network engineer > >> >> JSC DATAGROUP > >> >> > >> >> Monday, October 19, 2009, 3:30:51 AM, Onam wrote: > >> >> > >> >> > Hi experts, > >> >> > >> >> > I want to make logical interfaces on a physical interface ge-0/2/0 of > >> >> > a Juniper M10 router to > >> >> > connected to a the trunk port of a Summit Extreme x450 with the > >> >> > ethertype 0x88a8 (IEEE 802.1ad). > >> >> > >> >> > I have the following configuration on the router. > >> >> > >> >> > ge-0/2/0 { > >> >> > vlan-tagging; > >> >> > gigether-options { > >> >> > ethernet-switch-profile { > >> >> > tag-protocol-id 0x88a8; > >> >> > } > >> >> > } > >> >> > unit 50 { > >> >> > vlan-tags outer 0x88a8.50; > >> >> > family inet { > >> >> > address 192.168.175.169/28; > >> >> > } > >> >> > } > >> >> > } > >> >> > >> >> > I made the test with the 802.1q and it works but with 802.1ad didn't > >> >> > work. > >> >> > >> >> > Best regards. > >> >> > > >> >> > _________________________________________________________________ > >> >> > News, entertainment and everything you care about at Live.com. Get it > >> >> > now! > >> >> > http://www.live.com/getstarted.aspx > >> >> > _______________________________________________ > >> >> > juniper-nsp mailing list juniper-nsp@puck.nether.net > >> >> > https://puck.nether.net/mailman/listinfo/juniper-nsp > >> >> > >> > >> > Get news, entertainment and everything you care about at Live.com. Check > >> > it out! > >> > > > Invite your mail contacts to join your friends list with Windows Live > > Spaces. It's easy! Try it! > _________________________________________________________________ Connect to the next generation of MSN Messenger http://imagine-msn.com/messenger/launch80/default.aspx?locale=en-us&source=wlmailtagline _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp