Does it also work on a non uplink module ie EX 4200-24F? -----Original Message----- From: juniper-nsp-boun...@puck.nether.net [mailto:juniper-nsp-boun...@puck.nether.net] On Behalf Of Chuck Anderson Sent: Tuesday, December 15, 2009 4:41 PM To: juniper-nsp@puck.nether.net Subject: Re: [j-nsp] Juniper 10GE XFP
On Mon, Dec 14, 2009 at 03:53:16PM -0600, Jay Hanke wrote: > The EX is a different animal, I think there is only support for DOM > on the XFP ports unlike the MX where it is supported on all the SFP > and XFP ports. Also, I think DOM support is recent (10.0?) on the > EX. No, DOM works on SFP on EX4200 with 10.0. ex4200> show interfaces diagnostics optics ge-0/1/0 Physical interface: ge-0/1/0 Laser bias current : 23.140 mA Laser output power : 0.2170 mW / -6.64 dBm Module temperature : 47 degrees C / 117 degrees F Module voltage : 3.2470 V Receiver signal average optical power : 0.0006 mW / -32.22 dBm Laser bias current high alarm : Off Laser bias current low alarm : Off Laser bias current high warning : Off Laser bias current low warning : Off Laser output power high alarm : Off Laser output power low alarm : Off Laser output power high warning : Off Laser output power low warning : Off Module temperature high alarm : Off Module temperature low alarm : Off Module temperature high warning : Off Module temperature low warning : Off Module voltage high alarm : Off Module voltage low alarm : Off Module voltage high warning : Off Module voltage low warning : Off Laser rx power high alarm : Off Laser rx power low alarm : On Laser rx power high warning : Off Laser rx power low warning : Off Laser bias current high alarm threshold : 79.998 mA Laser bias current low alarm threshold : 0.000 mA Laser bias current high warning threshold : 69.998 mA Laser bias current low warning threshold : 3.998 mA Laser output power high alarm threshold : 0.7940 mW / -1.00 dBm Laser output power low alarm threshold : 0.0790 mW / -11.02 dBm Laser output power high warning threshold : 0.6300 mW / -2.01 dBm Laser output power low warning threshold : 0.1000 mW / -10.00 dBm Module temperature high alarm threshold : 85 degrees C / 185 degrees F Module temperature low alarm threshold : -5 degrees C / 23 degrees F Module temperature high warning threshold : 80 degrees C / 176 degrees F Module temperature low warning threshold : 0 degrees C / 32 degrees F Module voltage high alarm threshold : 3.599 V Module voltage low alarm threshold : 3.000 V Module voltage high warning threshold : 3.499 V Module voltage low warning threshold : 3.100 V Laser rx power high alarm threshold : 0.7943 mW / -1.00 dBm Laser rx power low alarm threshold : 0.0079 mW / -21.02 dBm Laser rx power high warning threshold : 0.6309 mW / -2.00 dBm Laser rx power low warning threshold : 0.0099 mW / -20.04 dBm ex4200> show interfaces ge-0/1/0 terse Interface Admin Link Proto Local Remote ge-0/1/0 up down ge-0/1/0.0 up down eth-switch ex4200> show chassis hardware ... PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T PIC 1 REV 04 711-026017 ............ 4x GE SFP+ Xcvr 0 REV 01 740-011614 ......... SFP-LX10 ex4200> show chassis pic fpc-slot 0 pic-slot 1 FPC slot 0, PIC slot 1 information: Type 4x GE SFP+ State Online PIC version 1.4 Uptime 18 hours, 12 minutes, 48 seconds PIC port information: Fiber Xcvr vendor Port Cable type type Xcvr vendor part number Wavelength 0 GIGE 1000LX10 SM OPNEXT INC TRF5736AALB214 1310 nm _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp