Try adding the interface (ge-0/0/7.0) under the 'site' definition in the routing instance config.....it's required, as far as I know. The rest looks pretty familiar.
David On 1 March 2012 17:06, Craig Whitmore <len...@orcon.net.nz> wrote: > Hi there > > I am pretty new to MPLS but what I'm trying to do is set up a L2 Tunnel > between 2 Routers via VPLS. The idea is the customer can plug a TRUNK port > at both ends and run whatever VLANS they want between them . Maybe there is > a easier way to do it. There are LOTS of examples in LOTS of different > places on how VPLS should be set up and all are slightly different. I > cannot > get any data thru the VPLS connection.. > > The set up is 2 Juniper Routers running OSPF between them and then BGP > between the Loopbacks also running MPLS/LDP etc > > The Config is (the same on both ends basically) > > ge-0/0/7 { > description "VPLS"; > per-unit-scheduler; > encapsulation ethernet-vpls; > unit 0 { > family vpls; > } > } > > VPLS-Customer { > instance-type vpls; > interface ge-0/0/7.0; > route-distinguisher XXXXX:2000; (XXXXXX:1000 on other side).. (XXXX = > the AS number) > vrf-target target:XXXXX:100; > protocols { > vpls { > site-range 10; > no-tunnel-services; > site router-2000 { > site-identifier 5; (different on both sides) > } > } > } > } > > > Debug.. > > # show vpls connections extensive > > Instance: VPLS-Customer > Local site: router-2000 (5) > Number of local interfaces: 1 > Number of local interfaces up: 1 > IRB interface present: no > ge-0/0/7.0 > lsi.1049090 6 Intf - vpls VPLS-Customer local site 5 > remote site 6 > Label-base Offset Size Range Preference > 262153 1 8 8 100 > connection-site Type St Time last up # Up trans > 6 rmt Up Mar 2 11:32:17 2012 1 > Remote PE: Y.Y.Y.Y, Negotiated control-word: No (Y.Y.Y.Y = Loopback of > other router) > Incoming label: 262158, Outgoing label: 262165 > Local interface: lsi.1049090, Status: Up, Encapsulation: VPLS > Description: Intf - vpls VPLS-Customer local site 5 remote site 6 > Connection History: > Mar 2 11:32:17 2012 status update timer > Mar 2 11:32:17 2012 loc intf up lsi.1049090 > Mar 2 11:32:17 2012 PE route changed > Mar 2 11:32:17 2012 Out lbl Update 262165 > Mar 2 11:32:17 2012 In lbl Update 262158 > Mar 2 11:32:17 2012 loc intf down > > > #show bgp summary instance VPLS-Customer > > Groups: 0 Peers: 0 Down peers: 0 > Table Tot Paths Act Paths Suppressed History Damp State > Pending > VPLS.l2vpn.0 1 1 0 0 0 > 0 > > # show bgp summary. > > Peer AS InPkt OutPkt OutQ Flaps Last > Up/Dwn State|#Active/Received/Accepted/Damped... > Y.Y.Y.Y 56030 6057 4657 0 0 1d 11:40:03 > Establ (Y.Y.Y.Y = IP Address of other routers loopback) > inet.0: 2/5156/2/0 > inet.2: 0/0/0/0 > bgp.l2vpn.0: 1/1/1/0 > bgp.l3vpn.0: 0/0/0/0 > VPLS-Customer.l2vpn.0: 1/1/1/0 > > > > > > > _______________________________________________ > juniper-nsp mailing list juniper-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/juniper-nsp > _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp