Hi Bill The smallest one I have is the Bosch 1604. It is a plunge router where the base is removable. The diameter of the body is 3 1/2 " and it comes with both 1/4 and 1/2 " collets. Ron In a message dated 3/16/2014 8:32:29 A.M. Eastern Daylight Time, [email protected] writes:
To do just the inside of a plane bowl no but I have other plans for the router too Bill From: [email protected] [mailto:[email protected]] On Behalf Of [email protected] Sent: Sunday, 16 March 2014 11:15 PM To: [email protected] Subject: Re: routers Hi Bill Do you need a full range of 1/4" router bits to do the inside of a bowl? Ron In a message dated 3/16/2014 5:36:10 A.M. Eastern Daylight Time, [email protected]_ (mailto:[email protected]) writes: Yes I have. a screw on adaptor like a muscle chuck would be the go but I have never seen one of those I did think of a spindle grinder but same problem ¼ inch drive and also too low of rpms So it brings me back to looking for a small dia fixed base 1/2inch router And obviously I need the ½ inch drive to fit all the various magnate bits A range of legacy bits with ¼ shafts would solve the problem too but they don’t do that either But with fixed base routers being so popular in the US I thought there might be a small ½ inch one out there some where Bill From: [email protected]_ (mailto:[email protected]) [mailto:[email protected]] On Behalf Of Tim Krause Sent: Sunday, 16 March 2014 6:56 PM To: [email protected]_ (mailto:[email protected]) Subject: Re: routers I'm no help, I've only seen 1/4 on laminate trimmers and I've never seen an adapter that goes from 1/4 to 1/2. The next question would be could you bore a laminate trimmer to fit a 1/2 bit. The next thought would be a grinder that might take a 1/2 bit. I'm guessing you have thought of all of this. Good Luck, -Tim ----- Original Message ----- From: _Bill Bulkeley_ (mailto:[email protected]) To: [email protected]_ (mailto:[email protected]) Sent: Saturday, March 15, 2014 9:06 PM Subject: routers Ok guys I have a question what is the smallest fixed base or laminate router you have seen that takes ½ inch bits I’m looking for a thin router so I can get into a bowl on the router table I will make a mount to mount it to the saddle of our mills. So any ideas or places on line i can look at please pass it on to me Bill -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]_ (mailto:[email protected]) . To post to this group, send email to [email protected]_ (mailto:[email protected]) . Visit this group at http://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. ____________________________________ No virus found in this message. Checked by AVG - _www.avg.com_ (http://www.avg.com/) Version: 2014.0.4336 / Virus Database: 3722/7200 - Release Date: 03/15/14 No virus found in this message. Checked by AVG - _www.avg.com_ (http://www.avg.com/) Version: 2014.0.4336 / Virus Database: 3722/7200 - Release Date: 03/15/14 -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]_ (mailto:[email protected]) . To post to this group, send email to [email protected]_ (mailto:[email protected]) . Visit this group at http://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]_ (mailto:[email protected]) . To post to this group, send email to [email protected]_ (mailto:[email protected]) . Visit this group at http://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. ____________________________________ No virus found in this message. Checked by AVG - _www.avg.com_ (http://www.avg.com/) Version: 2014.0.4336 / Virus Database: 3722/7200 - Release Date: 03/15/14 No virus found in this message. Checked by AVG - _www.avg.com_ (http://www.avg.com/) Version: 2014.0.4336 / Virus Database: 3722/7200 - Release Date: 03/15/14 -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]_ (mailto:[email protected]) . To post to this group, send email to [email protected]_ (mailto:[email protected]) . Visit this group at http://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]_ (mailto:[email protected]) . To post to this group, send email to [email protected]_ (mailto:[email protected]) . Visit this group at http://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
