"Carlo E. Prelz" wrote: > > Subject: [linux-dvb] Re: Activation of a card via Nexus+VDR - Possible? > Date: ven, feb 06, 2004 at 04:26:40 +0100 > > Quoting Andreas Share ([EMAIL PROTECTED]): > > > this could be only a problem with you CICAM, because neither vdr or the > > driver touch anything in the stream you need for activation. Only if your > > CICAM is not supported by vdr the card could not be activated. > > > > If your provider is PREMIERE, and you use an older Irdeto 4.6/4.7/4.8 SE or > > an Alphacrypt CI with firmware < 2.02, then you must update your > > CICAM. > > Umm umm. Should not be the case: I bought the CICAM card expecially > for this use. It is a brand new AstonCrypt V1.05 (SECA), and the > service is CanaalNederland (the Netherlands). > > I have had the card activated again at the shop, and this is confirmed > from the card's menu. But I still see no output for those encrypted > channels that I should be able to see. > > I try with both vdr and the utilities that are included in > libdvb. With vdr I do not know what to write into the CA field of the > channel description. If I put 0, the screen remains black (for the > encrypted channels). I wanted to be sure that there would be a > communication to the card, so I added a printout in > > cCiConditionalAccessSupport::SendPMT > > For example, if I want to tune to SBS6 (on Astra, 12574 MHz, Hor, > SR 22000, video PID 514, audio PID 80, SID 5005), the following bytes > are sent to the CA: > > 0000: 03 13 8d 01 00 14 01 09 11 01 00 e6 41 00 6a ff > 0016: 00 00 00 00 00 00 02 04 1c 46 00 02 02 00 00 00 > 0032: 00 50 00 00 > > (the first byte is CPLM_ONLY) > > But then, nothing happens... > > I also tried with cam_test and cam_set. If cam_test is started as > follows: > > ./cam_test -q 12574000 -l H -r 22000000 -i 5005 -s > > I get as output: > > Warning: TP already defined: > ID: 1 SATID: 1 > Channel: SBS6 apid: 0x50 vpid: 0x202 ttpid: 0x20 > CAM Test: 0x138d 0x202 0x50 0x0 0xffff 0x6 > CAM Test: 0x138d 0x202 0x50 0x0 0xffff 0x6 > CAM Test: 0x138d 0x202 0x50 0x0 0xffff 0x13 > > and I see the following bytes are passed to the card: > > 0000: 01 01 a0 32 01 90 02 00 03 9f 80 32 29 03 13 8d > 0016: 01 00 14 01 09 11 01 00 e6 41 00 6a ff 00 00 00 > 0032: 00 00 00 02 04 1c 46 00 02 02 00 00 00 00 50 00 > 0048: 00 00 ff ff 00 00 > > (this is the complete message, which contains the bytes shown above), > but I see nothing happening after that, too. There is no output to the > V4L port, and if I use the -o flag to cam_test, the stream I receive > is still encrypted. > > So my question is: what is the correct procedure for tuning channels > that must be decrypted by the CAM module? Where will the decrypted > mpeg stream be found? > > I am copying Klaus, the author of the CI software. I hope you do not > get upset... There is so little information around on these topics. ...!
Have you tried VDR version 1.3.3? See ftp://ftp.cadsoft.de/vdr/Developer. Use a Ca value of 0 and VDR 1.3.3 will fill in the correct values automatically. Klaus -- Info: To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as subject.