[    0.000000] Linux version 2.6.22-odo4 (root@sixlark) (gcc version 4.1.3 20070601 (prerelease) (Debian 4.1.2-12)) #1 SMP Thu Jul 12 00:50:45 PDT 2007
[    0.000000] Command line: root=UUID=76fcb399-bbf1-41e6-9131-340cc952543f ro console=ttyS0,115200
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[    0.000000]  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
[    0.000000]  BIOS-e820: 000000007fff0000 - 000000007ffff000 (ACPI data)
[    0.000000]  BIOS-e820: 000000007ffff000 - 0000000080000000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 0000000280000000 (usable)
[    0.000000] end_pfn_map = 2621440
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP 000F6F20, 0024 (r2 ACPIAM)
[    0.000000] ACPI: XSDT 7FFF0100, 0054 (r1 A M I  OEMXSDT   7000626 MSFT       97)
[    0.000000] ACPI: FACP 7FFF0281, 00F4 (r1 A M I  OEMFACP   7000626 MSFT       97)
[    0.000000] ACPI: DSDT 7FFF0410, 3751 (r1  0AAAA 0AAAA000        0 INTL  2002026)
[    0.000000] ACPI: FACS 7FFFF000, 0040
[    0.000000] ACPI: APIC 7FFF0380, 0084 (r1 A M I  OEMAPIC   7000626 MSFT       97)
[    0.000000] ACPI: OEMB 7FFFF040, 0041 (r1 A M I  OEMBIOS   7000626 MSFT       97)
[    0.000000] ACPI: SRAT 7FFF3B70, 0110 (r1 A M I  OEMSRAT   7000626 MSFT       97)
[    0.000000] ACPI: HPET 7FFF3C80, 0038 (r1 A M I  OEMHPET   7000626 MSFT       97)
[    0.000000] ACPI: ASF! 7FFF3CC0, 0086 (r1 AMIASF AMDSTRET        1 INTL  2002026)
[    0.000000] SRAT: PXM 0 -> APIC 0 -> Node 0
[    0.000000] SRAT: PXM 1 -> APIC 1 -> Node 1
[    0.000000] SRAT: Node 0 PXM 0 100000-80000000
[    0.000000] SRAT: Node 1 PXM 1 180000000-280000000
[    0.000000] SRAT: Node 0 PXM 0 100000-180000000
[    0.000000] SRAT: Node 0 PXM 0 0-180000000
[    0.000000] Bootmem setup node 0 0000000000000000-0000000180000000
[    0.000000] Bootmem setup node 1 0000000180000000-0000000280000000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   DMA32        4096 ->  1048576
[    0.000000]   Normal    1048576 ->  2621440
[    0.000000] early_node_map[4] active PFN ranges
[    0.000000]     0:        0 ->      159
[    0.000000]     0:      256 ->   524272
[    0.000000]     0:  1048576 ->  1572864
[    0.000000]     1:  1572864 ->  2621440
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] Processor #0 (Bootup-CPU)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] Processor #1
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: IOAPIC (id[0x03] address[0xfebff000] gsi_base[24])
[    0.000000] IOAPIC[1]: apic_id 3, address 0xfebff000, GSI 24-27
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfebfe000] gsi_base[28])
[    0.000000] IOAPIC[2]: apic_id 4, address 0xfebfe000, GSI 28-31
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] Setting APIC routing to flat
[    0.000000] ACPI: HPET id: 0x102282a0 base: 0xfec01000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7f780000)
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] PERCPU: Allocating 33928 bytes of per cpu data
[    0.000000] Built 2 zonelists.  Total pages: 2061183
[    0.000000] Kernel command line: root=UUID=76fcb399-bbf1-41e6-9131-340cc952543f ro console=ttyS0,115200
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[    0.000000] Marking TSC unstable due to TSCs unsynchronized
[   86.202573] time.c: Detected 2191.537 MHz processor.
[   86.211980] Console: colour VGA+ 80x25
[   86.211987] Checking aperture...
[   86.211990] CPU 0: aperture @ e0000000 size 256 MB
[   86.211993] CPU 1: aperture @ e0000000 size 256 MB
[   86.313604] Memory: 8234488k/10485760k available (2008k kernel code, 153668k reserved, 906k data, 288k init)
[   86.392843] Calibrating delay using timer specific routine.. 4387.40 BogoMIPS (lpj=8774812)
[   86.392908] Security Framework v1.0.0 initialized
[   86.392914] SELinux:  Disabled at boot.
[   86.392918] Capability LSM initialized
[   86.393569] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[   86.401332] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[   86.405068] Mount-cache hash table entries: 256
[   86.405237] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[   86.405240] CPU: L2 Cache: 1024K (64 bytes/line)
[   86.405243] CPU 0/0 -> Node 0
[   86.405263] SMP alternatives: switching to UP code
[   86.405436] ACPI: Core revision 20070126
[   86.448007] Using local APIC timer interrupts.
[   86.493616] result 12451916
[   86.493618] Detected 12.451 MHz APIC timer.
[   86.496952] SMP alternatives: switching to SMP code
[   86.497005] Booting processor 1/2 APIC 0x1
[   86.507112] Initializing CPU#1
[   86.584732] Calibrating delay using timer specific routine.. 4383.15 BogoMIPS (lpj=8766310)
[   86.584741] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[   86.584744] CPU: L2 Cache: 1024K (64 bytes/line)
[   86.584747] CPU 1/1 -> Node 1
[   86.584887] AMD Opteron(tm) Processor 848 stepping 08
[   86.588746] Brought up 2 CPUs
[   87.535073] migration_cost=0,692
[   87.535375] NET: Registered protocol family 16
[   87.535483] ACPI: bus type pci registered
[   87.535494] PCI: Using configuration type 1
[   87.544544] ACPI: Interpreter enabled
[   87.544547] ACPI: Using IOAPIC for interrupt routing
[   87.552268] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   87.552989] PCI: Firmware left 0000:03:08.0 e100 interrupts enabled, disabling
[   87.556840] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[   87.556946] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[   87.557051] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[   87.557155] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[   87.557234] Linux Plug and Play Support v0.97 (c) Adam Belay
[   87.557246] pnp: PnP ACPI init
[   87.557257] ACPI: bus type pnp registered
[   87.560985] pnp: PnP ACPI: found 14 devices
[   87.560988] ACPI: ACPI bus type pnp unregistered
[   87.561079] usbcore: registered new interface driver usbfs
[   87.561124] usbcore: registered new interface driver hub
[   87.561174] usbcore: registered new device driver usb
[   87.561215] PCI: Using ACPI for IRQ routing
[   87.561218] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   87.561311] NET: Registered protocol family 8
[   87.561313] NET: Registered protocol family 20
[   87.561377] PCI-DMA: Disabling AGP.
[   87.567311] PCI-DMA: aperture base @ e0000000 size 262144 KB
[   87.567316] PCI-DMA: using GART IOMMU.
[   87.567331] PCI-DMA: Reserving 256MB of IOMMU area in the AGP aperture
[   87.568706] hpet0: at MMIO 0xfec01000, IRQs 2, 8, 0
[   87.568710] hpet0: 3 32-bit timers, 14318180 Hz
[   87.569798] ACPI: RTC can wake from S4
[   87.569939] pnp: 00:09: ioport range 0x680-0x6ff has been reserved
[   87.569942] pnp: 00:09: ioport range 0x295-0x296 has been reserved
[   87.569945] pnp: 00:09: ioport range 0x778-0x77f has been reserved
[   87.569948] pnp: 00:09: ioport range 0xb78-0xb7f has been reserved
[   87.569951] pnp: 00:09: ioport range 0xf78-0xf7f has been reserved
[   87.569968] pnp: 00:0c: ioport range 0xca0-0xcaf has been reserved
[   87.569973] pnp: 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
[   87.569977] pnp: 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
[   87.569981] pnp: 00:0c: iomem range 0xfff80000-0xffffffff could not be reserved
[   87.569984] pnp: 00:0c: iomem range 0xff780000-0xff7fffff could not be reserved
[   87.569994] pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved
[   87.569997] pnp: 00:0d: iomem range 0xc0000-0xdffff has been reserved
[   87.570000] pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[   87.570003] pnp: 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
[   87.570442] PCI: Bridge: 0000:00:06.0
[   87.570445]   IO window: 9000-bfff
[   87.570450]   MEM window: fc900000-feafffff
[   87.570453]   PREFETCH window: disabled.
[   87.570460] PCI: Bridge: 0000:00:0a.0
[   87.570462]   IO window: 8000-8fff
[   87.570466]   MEM window: fa700000-fc8fffff
[   87.570470]   PREFETCH window: ff500000-ff5fffff
[   87.570475] PCI: Bridge: 0000:00:0b.0
[   87.570477]   IO window: 7000-7fff
[   87.570480]   MEM window: f9500000-fa6fffff
[   87.570483]   PREFETCH window: ff400000-ff4fffff
[   87.570584] NET: Registered protocol family 2
[   87.572229] Time: hpet clocksource has been installed.
[   87.612444] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[   87.616626] TCP established hash table entries: 1048576 (order: 12, 25165824 bytes)
[   87.637832] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[   87.638576] TCP: Hash tables configured (established 1048576 bind 65536)
[   87.638580] TCP reno registered
[   87.652346] checking if image is initramfs... it is
[   88.070768] Freeing initrd memory: 5895k freed
[   88.076131] audit: initializing netlink socket (disabled)
[   88.076151] audit(1184231361.828:1): initialized
[   88.076254] Total HugeTLB memory allocated, 0
[   88.076387] VFS: Disk quotas dquot_6.5.1
[   88.076401] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[   88.076495] io scheduler noop registered
[   88.076497] io scheduler anticipatory registered
[   88.076500] io scheduler deadline registered
[   88.076515] io scheduler cfq registered (default)
[   88.076535] PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for 0000:00:0a.0 subordinate bus.
[   88.076543] PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for 0000:00:0b.0 subordinate bus.
[   88.081926] Real Time Clock Driver v1.12ac
[   88.082068] Linux agpgart interface v0.102 (c) Dave Jones
[   88.082071] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   88.082564] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   89.098088] 00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   89.104960] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   89.113267] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[   89.119911] PNP: PS/2 controller doesn't have AUX irq; using default 12
[   89.129230] serio: i8042 KBD port at 0x60,0x64 irq 1
[   89.134338] serio: i8042 AUX port at 0x60,0x64 irq 12
[   89.139667] mice: PS/2 mouse device common for all mice
[   89.145210] TCP bic registered
[   89.148393] NET: Registered protocol family 1
[   89.152896] NET: Registered protocol family 17
[   89.157696] Freeing unused kernel memory: 288k freed
Loading, please wait...
[   89.179784] input: AT Translated Set 2 keyboard as /class/input/input0
Begin: Loading essential drivers... ...
Done.
Begin: Running /scripts/init-premount ...
[   89.314475] ACPI: Processor [CPU1] (supports 8 throttling states)
[   89.320862] ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
[   89.330782] ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
[   89.462537] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   89.469348] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[   89.524356] ACPI: PCI Interrupt 0000:03:00.0[D] -> GSI 19 (level, low) -> IRQ 19
[   89.532940] ohci_hcd 0000:03:00.0: OHCI Host Controller
[   89.538671] ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
[   89.546647] ohci_hcd 0000:03:00.0: irq 19, io mem 0xfeafc000
[   89.552843] SCSI subsystem initialized
[   89.590688] 3ware Storage Controller device driver for Linux v1.26.02.002.
[   89.600804] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[   89.607081] e100: Copyright(c) 1999-2006 Intel Corporation
[   89.618825] usb usb1: configuration #1 chosen from 1 choice
[   89.624966] hub 1-0:1.0: USB hub found
[   89.629032] hub 1-0:1.0: 3 ports detected
[   89.739201] ACPI: PCI Interrupt 0000:03:00.1[D] -> GSI 19 (level, low) -> IRQ 19
[   89.747552] ohci_hcd 0000:03:00.1: OHCI Host Controller
[   89.753470] ohci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 2
[   89.761391] ohci_hcd 0000:03:00.1: irq 19, io mem 0xfeafd000
[   89.829340] usb usb2: configuration #1 chosen from 1 choice
[   89.835464] hub 2-0:1.0: USB hub found
[   89.839501] hub 2-0:1.0: 3 ports detected
[   89.951072] AMD8111: IDE controller at PCI slot 0000:00:07.1
[   89.957139] AMD8111: chipset revision 3
[   89.961256] AMD8111: not 100% native mode: will probe irqs later
[   89.967697] AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller
[   89.973856]     ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
[   89.981620]     ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
[   91.130293] tg3.c:v3.77 (May 31, 2007)
[   91.134350] ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 24 (level, low) -> IRQ 24
[   91.170369] eth0: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCI:33MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:2d:4c:32
[   91.182865] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[   91.190888] eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
[   91.196502] ACPI: PCI Interrupt 0000:02:09.1[B] -> GSI 25 (level, low) -> IRQ 25
[   91.236894] eth1: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCI:33MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:2d:4c:33
[   91.249321] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[   91.257316] eth1: dma_rwctrl[763f0000] dma_mask[64-bit]
[   91.263098] ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 26 (level, low) -> IRQ 26
[   93.400975] scsi0 : 3ware Storage Controller
[   93.405741] 3w-xxxx: scsi0: Found a 3ware Storage Controller at 0x8c00, IRQ: 26.
[   93.413923] scsi 0:0:0:0: Direct-Access     3ware    Logical Disk 0   1.2  PQ: 0 ANSI: 0
[   93.423048] scsi 0:0:1:0: Direct-Access     3ware    Logical Disk 1   1.2  PQ: 0 ANSI: 0
[   93.432164] scsi 0:0:2:0: Direct-Access     3ware    Logical Disk 2   1.2  PQ: 0 ANSI: 0
[   93.443285] ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 27 (level, low) -> IRQ 27
[   95.635741] scsi1 : 3ware Storage Controller
[   95.640451] 3w-xxxx: scsi1: Found a 3ware Storage Controller at 0x8880, IRQ: 27.
[   95.651162] ACPI: PCI Interrupt 0000:03:08.0[A] -> GSI 18 (level, low) -> IRQ 18
[   95.739960] e100: eth2: e100_probe: addr 0xfeafb000, irq 18, MAC addr 00:E0:81:2D:4B:E1
[   95.746838] sd 0:0:0:0: [sda] 398297088 512-byte hardware sectors (203928 MB)
[   95.746856] sd 0:0:0:0: [sda] Write Protect is off
[   95.747151] sd 0:0:0:0: [sda] Write cache: disabled, read cache: disabled, supports DPO and FUA
[   95.747509] sd 0:0:0:0: [sda] 398297088 512-byte hardware sectors (203928 MB)
[   95.747518] sd 0:0:0:0: [sda] Write Protect is off
[   95.747811] sd 0:0:0:0: [sda] Write cache: disabled, read cache: disabled, supports DPO and FUA
[   95.747815]  sda: sda1 sda2 < sda5 >
[   95.796808] ACPI: PCI Interrupt 0000:03:05.0[A] -> <5>sd 0:0:0:0: [sda] Attached SCSI disk
[   95.798875] sd 0:0:1:0: [sdb] 398297088 512-byte hardware sectors (203928 MB)
[   95.798889] sd 0:0:1:0: [sdb] Write Protect is off
[   95.799185] sd 0:0:1:0: [sdb] Write cache: disabled, read cache: disabled, supports DPO and FUA
[   95.799515] sd 0:0:1:0: [sdb] 398297088 512-byte hardware sectors (203928 MB)
[   95.799523] sd 0:0:1:0: [sdb] Write Protect is off
[   95.799819] sd 0:0:1:0: [sdb] Write cache: disabled, read cache: disabled, supports DPO and FUA
[   95.799822]  sdb: sdb1
[   95.852291] GSI 19 (level, low) -> IRQ 19
[   95.852573] sd 0:0:1:0: [sdb] Attached SCSI disk
[   95.853031] sd 0:0:2:0: [sdc] 398297088 512-byte hardware sectors (203928 MB)
[   95.853039] sd 0:0:2:0: [sdc] Write Protect is off
[   95.853330] sd 0:0:2:0: [sdc] Write cache: disabled, read cache: disabled, supports DPO and FUA
[   95.853645] sd 0:0:2:0: [sdc] 398297088 512-byte hardware sectors (203928 MB)
[   95.853653] sd 0:0:2:0: [sdc] Write Protect is off
[   95.853945] sd 0:0:2:0: [sdc] Write cache: disabled, read cache: disabled, supports DPO and FUA
[   95.853947]  sdc: sdc1
[   95.908600] scsi2 : sata_sil
[   95.908870] sd 0:0:2:0: [sdc] Attached SCSI disk
[   95.916743] scsi3 : sata_sil
[   95.919783] scsi4 : sata_sil
[   95.922851] scsi5 : sata_sil
[   95.925946] ata1: SATA max UDMA/100 cmd 0xffffc20002738c80 ctl 0xffffc20002738c8a bmdma 0xffffc20002738c00 irq 19
[   95.936921] ata2: SATA max UDMA/100 cmd 0xffffc20002738cc0 ctl 0xffffc20002738cca bmdma 0xffffc20002738c08 irq 19
[   95.947815] ata3: SATA max UDMA/100 cmd 0xffffc20002738e80 ctl 0xffffc20002738e8a bmdma 0xffffc20002738e00 irq 19
[   95.958718] ata4: SATA max UDMA/100 cmd 0xffffc20002738ec0 ctl 0xffffc20002738eca bmdma 0xffffc20002738e08 irq 19
[   96.283395] ata1: SATA link down (SStatus 0 SControl 310)
[   96.603214] ata2: SATA link down (SStatus 0 SControl 310)
[   96.923040] ata3: SATA link down (SStatus 0 SControl 310)
[   97.242861] ata4: SATA link down (SStatus 0 SControl 310)
[   97.248802] sata_mv 0000:01:03.0: version 0.81hack7
[   97.255028] ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 28 (level, low) -> IRQ 28
[   97.266860] sata_mv 0000:01:03.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx
[   97.274920] scsi6 : sata_mv
[   97.277983] scsi7 : sata_mv
[   97.281047] scsi8 : sata_mv
[   97.284100] scsi9 : sata_mv
[   97.287127] scsi10 : sata_mv
[   97.290252] scsi11 : sata_mv
[   97.293380] scsi12 : sata_mv
[   97.296521] scsi13 : sata_mv
[   97.299645] ata5: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc200027a2120 bmdma 0x0000000000000000 irq 28
[   97.310627] ata6: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc200027a4120 bmdma 0x0000000000000000 irq 28
[   97.321609] ata7: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc200027a6120 bmdma 0x0000000000000000 irq 28
[   97.332591] ata8: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc200027a8120 bmdma 0x0000000000000000 irq 28
[   97.343564] ata9: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc200027b2120 bmdma 0x0000000000000000 irq 28
[   97.354548] ata10: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc200027b4120 bmdma 0x0000000000000000 irq 28
[   97.365625] ata11: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc200027b6120 bmdma 0x0000000000000000 irq 28
[   97.376692] ata12: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc200027b8120 bmdma 0x0000000000000000 irq 28
[   97.926491] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   97.990476] ata5.00: ATA-7: ST3400620AS, 3.AAC, max UDMA/133
[   97.996259] ata5.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
[   98.070431] ata5.00: configured for UDMA/133
[   98.614108] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   98.678094] ata6.00: ATA-7: ST3400620AS, 3.AAC, max UDMA/133
[   98.683916] ata6.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
[   98.742059] ata6.00: configured for UDMA/133
[   99.285739] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   99.349725] ata7.00: ATA-7: ST3400620AS, 3.AAC, max UDMA/133
[   99.355791] ata7.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
[   99.429680] ata7.00: configured for UDMA/133
[   99.973358] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  100.037344] ata8.00: ATA-7: ST3400620AS, 3.AAC, max UDMA/133
[  100.043169] ata8.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32)
[  100.101309] ata8.00: configured for UDMA/133
[  100.141259] ata9: SATA link down (SStatus 0 SControl 300)
[  100.181236] ata10: SATA link down (SStatus 0 SControl 300)
[  100.221215] ata11: SATA link down (SStatus 0 SControl 300)
[  100.261192] ata12: SATA link down (SStatus 0 SControl 300)
[  100.267192] scsi 6:0:0:0: Direct-Access     ATA      ST3400620AS      3.AA PQ: 0 ANSI: 5
[  100.275916] sd 6:0:0:0: [sdd] 781422768 512-byte hardware sectors (400088 MB)
[  100.283591] sd 6:0:0:0: [sdd] Write Protect is off
[  100.288711] sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  100.298445] sd 6:0:0:0: [sdd] 781422768 512-byte hardware sectors (400088 MB)
[  100.306094] sd 6:0:0:0: [sdd] Write Protect is off
[  100.311236] sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  100.320909]  sdd: sdd1
[  100.344082] sd 6:0:0:0: [sdd] Attached SCSI disk
[  100.349085] scsi 7:0:0:0: Direct-Access     ATA      ST3400620AS      3.AA PQ: 0 ANSI: 5
[  100.357787] sd 7:0:0:0: [sde] 781422768 512-byte hardware sectors (400088 MB)
[  100.365420] sd 7:0:0:0: [sde] Write Protect is off
[  100.370527] sd 7:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  100.380250] sd 7:0:0:0: [sde] 781422768 512-byte hardware sectors (400088 MB)
[  100.387884] sd 7:0:0:0: [sde] Write Protect is off
[  100.393044] sd 7:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  100.402713]  sde: sde1
[  100.420712] sd 7:0:0:0: [sde] Attached SCSI disk
[  100.425712] scsi 8:0:0:0: Direct-Access     ATA      ST3400620AS      3.AA PQ: 0 ANSI: 5
[  100.434415] sd 8:0:0:0: [sdf] 781422768 512-byte hardware sectors (400088 MB)
[  100.442064] sd 8:0:0:0: [sdf] Write Protect is off
[  100.447206] sd 8:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  100.456929] sd 8:0:0:0: [sdf] 781422768 512-byte hardware sectors (400088 MB)
[  100.464573] sd 8:0:0:0: [sdf] Write Protect is off
[  100.469732] sd 8:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  100.479430]  sdf: sdf1
[  100.494837] sd 8:0:0:0: [sdf] Attached SCSI disk
[  100.499864] scsi 9:0:0:0: Direct-Access     ATA      ST3400620AS      3.AA PQ: 0 ANSI: 5
[  100.508568] sd 9:0:0:0: [sdg] 781422768 512-byte hardware sectors (400088 MB)
[  100.516215] sd 9:0:0:0: [sdg] Write Protect is off
[  100.521339] sd 9:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  100.531056] sd 9:0:0:0: [sdg] 781422768 512-byte hardware sectors (400088 MB)
[  100.538707] sd 9:0:0:0: [sdg] Write Protect is off
[  100.543839] sd 9:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  100.553520]  sdg: sdg1
[  100.572585] sd 9:0:0:0: [sdg] Attached SCSI disk
Done.
Begin: Mounting root file system... ...
Begin: Running /scripts/local-top ...
Begin: Loading MD modules ...
Done.
Done.
Begin: Running /scripts/local-premount ...
Done.
[  101.001931] kjournald starting.  Commit interval 5 seconds
[  101.007650] EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
Done.
Mount failed for selinuxfs on /selinux:  No such file or directory
INIT: version 2.86 booting
Setting hostname to 'sixlark'...done.
* Files under mount point '/lib/init/rw' will be hidden.
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...[  102.944041] parport_pc 00:08: reported by Plug and Play ACPI
[  102.950191] parport0: PC-style at 0x378, irq 7 [PCSPP]
[  103.084755] input: PC Speaker as /class/input/input1
[  103.180802] AMD768 RNG detected
done.
Setting parameters of disc: (none).
Activating swap:swapon on /dev/sda5
[  103.774187] Adding 8080652k swap on /dev/sda5.  Priority:-1 extents:1 across:8080652k
.
Will now check root file system:fsck 1.40-WIP (07-Apr-2007)
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/sda1
/dev/sda1: clean, 749227/23887872 files, 9678153/47765253 blocks
.
[  103.905688] EXT3 FS on sda1, internal journal
Setting the system clock..
System Clock set. Local time: Thu Jul 12 09:09:39 UTC 2007.
Cleaning up ifupdown....
Loading kernel module loop.
[  104.601964] loop: module loaded
Loading kernel module i2c-amd756.
Loading kernel module i2c-isa.
Loading kernel module lm85.
Loading kernel module w83627hf.
[  104.760762] w83627hf: Found W83627HF chip at 0x290
Loading kernel module w83627hf_wdt.
WARNING: Not loading blacklisted module w83627hf_wdt
Loading device-mapper support[  104.842021] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
.
Loading device-mapper support.
Assembling MD arrays...done (disabled in /etc/default/mdadm).
Starting early crypto disks...done.
Starting remaining crypto disks...done.
Will now check all file systems.
fsck 1.40-WIP (07-Apr-2007)
Checking all file systems.
Done checking file systems.
A log is being saved in /var/log/fsck/checkfs if that location is writable.
Setting kernel variables...done.
Will now mount local filesystems:.
Will now activate swapfile swap:done.
Cleaning /tmp...done.
Cleaning /var/run...done.
Cleaning /var/lock...done.
Setting up networking....
Configuring network interfaces...done.
Starting portmap daemon....
Setting sensors limits: done.
Setting console screen modes and fonts.
Initializing random number generator...done.
Recovering nvi editor sessions...none found.
Setting up X server socket directory /tmp/.X11-unix....
Setting up ICE socket directory /tmp/.ICE-unix....
INIT: Entering runlevel: 2
Starting watchdog keepalive daemon: wd_keepalive.
Starting system log daemon....
Starting kernel log daemon....
Starting portmap daemon...Already running..
Loading ACPI modules...Loaded module: battery
Loaded module: ac
Module already loaded: processor
[  108.903288] input: Power Button (FF) as /class/input/input2
[  108.909360] ACPI: Power Button (FF) [PWRF]
[  108.916449] input: Power Button (CM) as /class/input/input3
[  108.922420] ACPI: Power Button (CM) [PWRB]
Loaded module: button
Module already loaded: fan
Module already loaded: thermal
.
Starting Advanced Configuration and Power Interface daemon....
Starting internet superserver: inetd.
[  109.147341] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[  109.153112] tg3: eth0: Flow control is on for TX and on for RX.
Starting Postfix Mail Transport Agent: postfix.
Starting Hardware RNG entropy gatherer daemon: rngd.
* Not starting S.M.A.R.T. daemon smartd, disabled via /etc/default/smartmontools
Starting OpenBSD Secure Shell server: sshd[  110.858608] NET: Registered protocol family 10
[  110.863521] lo: Disabled Privacy Extensions
.
Setting sysfs variables...done.
* sadc not enabled in /etc/default/sysstat, not starting.
Starting NFS common utilities: statd.
Starting NTP server: ntpd.
Starting periodic command scheduler: crond.
Stopping watchdog keepalive daemon:
Starting watchdog daemon: watchdog.
Starting web server (apache2)....
Starting Munin-Node: done.
enabling clock divisor of 512 in halt...ok.
Running local boot scripts (/etc/rc.local).

Debian GNU/Linux lenny/sid sixlark ttyS0

sixlark login: [  462.377637] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[  462.388150] SGI XFS Quota Management subsystem
[  462.441112] XFS mounting filesystem sdd1
[  465.771995] XFS mounting filesystem sde1
[  469.270947] XFS mounting filesystem sdf1
[  472.613546] XFS mounting filesystem sdg1
