early console in setup code
Probing EDD (edd=off to disable)... ok
[    0.000000] Linux version 4.14.0-rc6-00022-geb948c7 (kbuild@lkp-hsx03) (gcc version 5.4.1 20160904 (Debian 5.4.1-2)) #1 SMP Sat Oct 28 12:17:13 CST 2017
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] x86/fpu: x87 FPU will use FXSAVE
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000013fdbfff] usable
[    0.000000] BIOS-e820: [mem 0x0000000013fdc000-0x0000000013ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[    0.000000] Hypervisor detected: KVM
[    0.000000] tsc: Fast TSC calibration failed
[    0.000000] tsc: Unable to calibrate against PIT
[    0.000000] tsc: No reference (HPET/PMTIMER) available
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x13fdc max_arch_pfn = 0x100000
[    0.000000] MTRR: Disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WT  UC- UC  WB  WT  UC- UC  
[    0.000000] Scan for SMP in [mem 0x00000000-0x000003ff]
[    0.000000] Scan for SMP in [mem 0x0009fc00-0x0009ffff]
[    0.000000] Scan for SMP in [mem 0x000f0000-0x000fffff]
[    0.000000] found SMP MP-table at [mem 0x000f6a90-0x000f6a9f] mapped at [ffc67a90]
[    0.000000]   mpc: f6aa0-f6b80
[    0.000000] initial memory mapped: [mem 0x00000000-0x027fffff]
[    0.000000] Base memory trampoline at [b009b000] 9b000 size 16384
[    0.000000] BRK [0x0230c000, 0x0230cfff] PGTABLE
[    0.000000] RAMDISK: [mem 0x13538000-0x13fcffff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F68C0 000014 (v00 BOCHS )
[    0.000000] ACPI: RSDT 0x0000000013FE15CE 000030 (v01 BOCHS  BXPCRSDT 00000001 BXPC 00000001)
[    0.000000] ACPI: FACP 0x0000000013FE142A 000074 (v01 BOCHS  BXPCFACP 00000001 BXPC 00000001)
[    0.000000] ACPI: DSDT 0x0000000013FE0040 0013EA (v01 BOCHS  BXPCDSDT 00000001 BXPC 00000001)
[    0.000000] ACPI: FACS 0x0000000013FE0000 000040
[    0.000000] ACPI: APIC 0x0000000013FE151E 000078 (v01 BOCHS  BXPCAPIC 00000001 BXPC 00000001)
[    0.000000] ACPI: HPET 0x0000000013FE1596 000038 (v01 BOCHS  BXPCHPET 00000001 BXPC 00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] mapped APIC to         ffffc000 (        fee00000)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 319MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 13fdc000
[    0.000000]   low ram: 0 - 13fdc000
[    0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00
[    0.000000] kvm-clock: cpu 0, msr 0:13fdb001, primary cpu clock
[    0.000000] kvm-clock: using sched offset of 1978995511 cycles
[    0.000000] clocksource: kvm-clock: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[    0.000000] BRK [0x0230d000, 0x0230dfff] PGTABLE
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000001000-0x0000000013fdbfff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009efff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x0000000013fdbfff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000013fdbfff]
[    0.000000] On node 0 totalpages: 81786
[    0.000000]   Normal zone: 640 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 81786 pages, LIFO batch:15
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x608
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[    0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 0, APIC INT 02
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level)
[    0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 05, APIC ID 0, APIC INT 05
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 0, APIC INT 09
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level)
[    0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0a, APIC ID 0, APIC INT 0a
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level)
[    0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0b, APIC ID 0, APIC INT 0b
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 0, APIC INT 01
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 0, APIC INT 03
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 0, APIC INT 04
[    0.000000] ACPI: IRQ5 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 0, APIC INT 06
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 0, APIC INT 07
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 0, APIC INT 08
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ10 used by override.
[    0.000000] ACPI: IRQ11 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 0, APIC INT 0c
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 0, APIC INT 0d
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 0, APIC INT 0e
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 0, APIC INT 0f
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] mapped IOAPIC to ffffb000 (fec00000)
[    0.000000] e820: [mem 0x14000000-0xfeffbfff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on KVM
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[    0.000000] random: fast init done
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:1 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] percpu: Embedded 341 pages/cpu @c3163000 s1367808 r0 d28928 u1396736
[    0.000000] pcpu-alloc: s1367808 r0 d28928 u1396736 alloc=341*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] KVM setup async PF for cpu 0
[    0.000000] kvm-stealtime: cpu 0, msr 13165b00
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 81146
[    0.000000] Kernel command line: ip=::::vm-lkp-wsx03-openwrt-i386-31::dhcp root=/dev/ram0 user=lkp job=/lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.yaml ARCH=i386 kconfig=i386-randconfig-b0-10280741 branch=linux-devel/devel-spot-201710280538 commit=eb948c71f790f4fd27440895ca19180a78fd3016 BOOT_IMAGE=/pkg/linux/i386-randconfig-b0-10280741/gcc-5/eb948c71f790f4fd27440895ca19180a78fd3016/vmlinuz-4.14.0-rc6-00022-geb948c7 max_uptime=1500 RESULT_ROOT=/result/trinity/300s/vm-lkp-wsx03-openwrt-i386/openwrt-i386-2016-03-16.cgz/i386-randconfig-b0-10280741/gcc-5/eb948c71f790f4fd27440895ca19180a78fd3016/0 LKP_SERVER=inn debug apic=debug sysrq_always_enabled rcupdate.rcu_cpu_stall_timeout=100 net.ifnames=0 printk.devkmsg=on panic=-1 softlockup_panic=1 nmi_watchdog=panic oops=panic load_ramdisk=2 prompt_ramdisk=0 drbd.minor_count=8 systemd.log_level=err ignore_loglevel console=tty0 earlyprintk=tty
[    0.000000] sysrq: sysrq always enabled.
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (00000000:00000000)
[    0.000000] Memory: 292356K/327144K available (6137K kernel code, 1134K rwdata, 3760K rodata, 1888K init, 6428K bss, 34788K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xffe66000 - 0xfffff000   (1636 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xc47dc000 - 0xff7fe000   ( 944 MB)
[    0.000000]     lowmem  : 0xb0000000 - 0xc3fdc000   ( 319 MB)
[    0.000000]       .init : 0xb1ade000 - 0xb1cb6000   (1888 kB)
[    0.000000]       .data : 0xb15fe524 - 0xb1ac7a40   (4901 kB)
[    0.000000]       .text : 0xb1000000 - 0xb15fe524   (6137 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] ftrace: allocating 29479 entries in 58 pages
[    0.001000] Hierarchical RCU implementation.
[    0.001000] 	RCU event tracing is enabled.
[    0.001000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.001000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[    0.001000] 	RCU callback double-/use-after-free debug enabled.
[    0.001000] 	RCU debug extended QS entry/exit.
[    0.001000] 	RCU CPU stall warnings timeout set to 100 (rcu_cpu_stall_timeout).
[    0.001000] 	Tasks RCU enabled.
[    0.001000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.001000] NR_IRQS: 2304, nr_irqs: 256, preallocated irqs: 16
[    0.001000] CPU 0 irqstacks, hard=b0110000 soft=b0112000
[    0.001000] console [ttyS0] enabled
[    0.001000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.001000] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.001000] ... MAX_LOCK_DEPTH:          48
[    0.001000] ... MAX_LOCKDEP_KEYS:        8191
[    0.001000] ... CLASSHASH_SIZE:          4096
[    0.001000] ... MAX_LOCKDEP_ENTRIES:     32768
[    0.001000] ... MAX_LOCKDEP_CHAINS:      65536
[    0.001000] ... CHAINHASH_SIZE:          32768
[    0.001000]  memory used by lock dependency info: 4639 kB
[    0.001000]  per task-struct memory footprint: 2112 bytes
[    0.001000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
[    0.001000] hpet clockevent registered
[    0.002101] tsc: Detected 2260.998 MHz processor
[    0.003071] Calibrating delay loop (skipped) preset value.. 4521.99 BogoMIPS (lpj=2260998)
[    0.005101] pid_max: default: 32768 minimum: 301
[    0.006484] ACPI: Core revision 20170728
[    0.091456] ACPI: 1 ACPI AML tables successfully acquired and loaded
[    0.093543] Security Framework initialized
[    0.095484] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.096224] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.106223] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[    0.107094] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[    0.159643] Freeing SMP alternatives memory: 20K
[    0.170555] smpboot: Max logical packages: 1
[    0.171202] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.174128] enabled ExtINT on CPU#0
[    0.193352] ENABLING IO-APIC IRQs
[    0.195216] init IO_APIC IRQs
[    0.196097]  apic 0 pin 0 not connected
[    0.198128] IOAPIC[0]: Set routing entry (0-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:1)
[    0.199260] IOAPIC[0]: Set routing entry (0-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-5 -> 0x35 -> IRQ 5 Mode:1 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-10 -> 0x3a -> IRQ 10 Mode:1 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-11 -> 0x3b -> IRQ 11 Mode:1 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:1)
[    0.200000]  apic 0 pin 16 not connected
[    0.200000]  apic 0 pin 17 not connected
[    0.200000]  apic 0 pin 18 not connected
[    0.200000]  apic 0 pin 19 not connected
[    0.200000]  apic 0 pin 20 not connected
[    0.200000]  apic 0 pin 21 not connected
[    0.200000]  apic 0 pin 22 not connected
[    0.200000]  apic 0 pin 23 not connected
[    0.200000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.200000] Using local APIC timer interrupts.
[    0.200000] calibrating APIC timer ...
[    0.202000] ... lapic delta = 6645034
[    0.202000] ... PM-Timer delta = 380574
[    0.202000] APIC calibration not consistent with PM-Timer: 106ms instead of 100ms
[    0.202000] APIC delta adjusted to PM-Timer: 6250076 (6645034)
[    0.202000] TSC delta adjusted to PM-Timer: 226063216 (240348711)
[    0.202000] ..... delta 6250076
[    0.202000] ..... mult: 268438720
[    0.202000] ..... calibration result: 1000012
[    0.202000] ..... CPU clock speed is 2260.0632 MHz.
[    0.202000] ..... host bus clock speed is 1000.0012 MHz.
[    0.202683] smpboot: CPU0: Intel QEMU Virtual CPU version 2.5+ (family: 0x6, model: 0x6, stepping: 0x3)
[    0.206426] Performance Events: PMU not available due to virtualization, using software events only.
[    0.210427] Hierarchical SRCU implementation.
[    0.227322] NMI watchdog: Perf event create on CPU 0 failed with -2
[    0.228131] NMI watchdog: Perf NMI watchdog permanently disabled
[    0.230518] smp: Bringing up secondary CPUs ...
[    0.231038] smp: Brought up 1 node, 1 CPU
[    0.232068] ----------------
[    0.233060] | NMI testsuite:
[    0.235068] --------------------
[    0.236054]   remote IPI:  ok  |
[    0.238032]    local IPI:  ok  |
[    0.239035] --------------------
[    0.240034] Good, all   2 testcases passed! |
[    0.241033] ---------------------------------
[    0.242057] smpboot: Total of 1 processors activated (4521.99 BogoMIPS)
[    0.248265] devtmpfs: initialized
[    0.264713] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.265154] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.269160] regulator-dummy: no parameters
[    0.272126] regulator-dummy: no parameters
[    0.274249] regulator-dummy: Failed to create debugfs directory
[    0.279901] NET: Registered protocol family 16
[    0.289223] EISA bus registered
[    0.290105] cpuidle: using governor menu
[    0.295679] ACPI: bus type PCI registered
[    0.305525] PCI: PCI BIOS revision 2.10 entry at 0xfd501, last bus=0
[    0.307063] PCI: Using configuration type 1 for base access
[    0.498781] ------------[ cut here ]------------
[    0.499097] WARNING: CPU: 0 PID: 1 at mm/hugetlb.c:2849 hugetlb_add_hstate+0x146/0x161
[    0.501039] Modules linked in:
[    0.502228] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.0-rc6-00022-geb948c7 #1
[    0.503064] task: b0138000 task.stack: b012a000
[    0.504067] EIP: hugetlb_add_hstate+0x146/0x161
[    0.505063] EFLAGS: 00210212 CPU: 0
[    0.506064] EAX: 00000000 EBX: 00000001 ECX: 00000000 EDX: 00000001
[    0.507064] ESI: ffc00000 EDI: 00000000 EBP: b012bee4 ESP: b012bed4
[    0.508065]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[    0.509065] CR0: 80050033 CR2: 00000000 CR3: 01cbe000 CR4: 00000690
[    0.510071] Call Trace:
[    0.511104]  hugetlb_init+0x58/0x4e1
[    0.512129]  ? up_write+0x1b/0x37
[    0.513096]  ? blocking_notifier_chain_register+0x56/0x60
[    0.514069]  ? mm_compute_batch_notifier+0x19/0x19
[    0.515070]  ? hugetlb_init+0x4e1/0x4e1
[    0.516095]  hugetlb_init+0x16/0x1d
[    0.517070]  do_one_initcall+0x80/0x14c
[    0.518130]  ? do_early_param+0x78/0x78
[    0.520096]  ? kernel_init_freeable+0xe7/0x17a
[    0.521191]  ? up_write+0x1b/0x37
[    0.522070]  ? kernel_init_freeable+0xe7/0x17a
[    0.523099]  kernel_init_freeable+0x107/0x17a
[    0.525064]  ? rest_init+0x115/0x115
[    0.526096]  kernel_init+0xd/0xd5
[    0.527094]  ret_from_fork+0x19/0x24
[    0.528165] Code: b3 b1 83 c4 10 31 db 81 7d f0 ff ff 3f 00 6a 00 b8 b8 58 a8 b1 0f 97 c3 31 c9 89 da e8 55 ee 5e ff 81 7d f0 ff ff 3f 00 58 76 02 <0f> ff 6a 00 31 c9 89 da b8 a0 58 a8 b1 e8 39 ee 5e ff 58 8d 65
[    0.532071] ---[ end trace 22f52a911eb8bbac ]---
[    0.533129] HugeTLB registered 4.00 MiB page size, pre-allocated 0 pages
[    0.540482] ACPI: Added _OSI(Module Device)
[    0.541163] ACPI: Added _OSI(Processor Device)
[    0.543066] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.544068] ACPI: Added _OSI(Processor Aggregator Device)
[    0.608834] ACPI: Interpreter enabled
[    0.609324] ACPI: (supports S0 S5)
[    0.610195] ACPI: Using IOAPIC for interrupt routing
[    0.612138] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.622000] ACPI: Enabled 2 GPEs in block 00 to 0F
[    0.813130] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.815102] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI]
[    0.817200] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.819167] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[    0.822189] PCI host bridge to bus 0000:00
[    0.823092] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.824093] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.826069] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.827071] pci_bus 0000:00: root bus resource [mem 0x14000000-0xfebfffff window]
[    0.828065] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.830199] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000
[    0.840583] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100
[    0.850321] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180
[    0.868067] pci 0000:00:01.1: reg 0x20: [io  0xc0c0-0xc0cf]
[    0.875267] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.876061] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.878056] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.879068] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.887423] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000
[    0.892038] pci 0000:00:01.3: quirk: [io  0x0600-0x063f] claimed by PIIX4 ACPI
[    0.893132] pci 0000:00:01.3: quirk: [io  0x0700-0x070f] claimed by PIIX4 SMB
[    0.898903] pci 0000:00:02.0: [1234:1111] type 00 class 0x030000
[    0.903158] pci 0000:00:02.0: reg 0x10: [mem 0xfd000000-0xfdffffff pref]
[    0.910165] pci 0000:00:02.0: reg 0x18: [mem 0xfebf0000-0xfebf0fff]
[    0.928136] pci 0000:00:02.0: reg 0x30: [mem 0xfebe0000-0xfebeffff pref]
[    0.935323] pci 0000:00:03.0: [8086:100e] type 00 class 0x020000
[    0.940063] pci 0000:00:03.0: reg 0x10: [mem 0xfebc0000-0xfebdffff]
[    0.943064] pci 0000:00:03.0: reg 0x14: [io  0xc000-0xc03f]
[    0.960091] pci 0000:00:03.0: reg 0x30: [mem 0xfeb80000-0xfebbffff pref]
[    0.967812] pci 0000:00:04.0: [1af4:1001] type 00 class 0x010000
[    0.972091] pci 0000:00:04.0: reg 0x10: [io  0xc040-0xc07f]
[    0.977064] pci 0000:00:04.0: reg 0x14: [mem 0xfebf1000-0xfebf1fff]
[    0.988093] pci 0000:00:04.0: reg 0x20: [mem 0xfe000000-0xfe003fff 64bit pref]
[    1.006819] pci 0000:00:05.0: [1af4:1001] type 00 class 0x010000
[    1.011065] pci 0000:00:05.0: reg 0x10: [io  0xc080-0xc0bf]
[    1.015068] pci 0000:00:05.0: reg 0x14: [mem 0xfebf2000-0xfebf2fff]
[    1.024155] pci 0000:00:05.0: reg 0x20: [mem 0xfe004000-0xfe007fff 64bit pref]
[    1.041838] pci 0000:00:06.0: [8086:25ab] type 00 class 0x088000
[    1.046068] pci 0000:00:06.0: reg 0x10: [mem 0xfebf3000-0xfebf300f]
[    1.073521] pci_bus 0000:00: on NUMA node 0
[    1.093074] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
[    1.098777] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *10 11)
[    1.105261] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10 *11)
[    1.110617] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10 *11)
[    1.113742] ACPI: PCI Interrupt Link [LNKS] (IRQs *9)
[    1.130524] ACPI: bus type USB registered
[    1.132578] usbcore: registered new interface driver usbfs
[    1.133548] usbcore: registered new interface driver hub
[    1.134454] usbcore: registered new device driver usb
[    1.137413] Linux video capture interface: v2.00
[    1.139717] EDAC MC: Ver: 3.0.0
[    1.143296] EDAC DEBUG: edac_mc_sysfs_init: device mc created
[    1.149704] PCI: Using ACPI for IRQ routing
[    1.150066] PCI: pci_cache_line_size set to 32 bytes
[    1.154184] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    1.155191] e820: reserve RAM buffer [mem 0x13fdc000-0x13ffffff]
[    1.167593] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    1.170778] clocksource: Switched to clocksource kvm-clock
[    1.253577] Warning: could not register annotated branches stats
[    1.608979] VFS: Disk quotas dquot_6.6.0
[    1.615271] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.626408] FS-Cache: Loaded
[    1.632404] pnp: PnP ACPI init
[    1.640924] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[    1.655385] pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active)
[    1.669997] pnp 00:02: Plug and Play ACPI device, IDs PNP0f13 (active)
[    1.682962] pnp 00:03: [dma 2]
[    1.689899] pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active)
[    1.705288] pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active)
[    1.721004] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.736363] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.767316] pnp: PnP ACPI: found 7 devices
[    1.825577] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    1.838511] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    1.847257] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    1.855847] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    1.865336] pci_bus 0000:00: resource 7 [mem 0x14000000-0xfebfffff window]
[    1.877907] NET: Registered protocol family 1
[    1.884367] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[    1.892823] pci 0000:00:01.0: PIIX3: Enabling Passive Release
[    1.901304] pci 0000:00:01.0: Activating ISA DMA hang workarounds
[    1.910519] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    1.922791] PCI: CLS 0 bytes, default 32
[    1.931711] Unpacking initramfs...
[   15.934363] Freeing initrd memory: 10848K
[   22.644892] Kprobe smoke test: started
[   23.166918] Kprobe smoke test: passed successfully
[   23.179943] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[   23.267792] fuse init (API version 7.26)
[   23.336308] test_printf: all 260 tests passed
[   23.342528] test_uuid: all 18 tests passed
[   23.349429] glob: 64 self-tests passed, 0 failed
[   23.360345] gpio_it87: no device
[   23.366338] gpio-mockup: probe of gpio-mockup failed with error -22
[   23.382025] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[   23.392300] ACPI: Power Button [PWRF]
[   23.402477] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[   23.412841] ACPI: Power Button [PWRF]
[   23.419721] Warning: Processor Platform Limit event detected, but not handled.
[   23.429569] Consider compiling CPUfreq support into your kernel.
[   26.951433] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[   38.456517] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[   45.504745] r3964: Philips r3964 Driver $Revision: 1.10 $
[   45.512877] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[   45.606860] 00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[   45.622872] console [ttyS0] disabled
[    0.000000] Linux version 4.14.0-rc6-00022-geb948c7 (kbuild@lkp-hsx03) (gcc version 5.4.1 20160904 (Debian 5.4.1-2)) #1 SMP Sat Oct 28 12:17:13 CST 2017
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] x86/fpu: x87 FPU will use FXSAVE
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000013fdbfff] usable
[    0.000000] BIOS-e820: [mem 0x0000000013fdc000-0x0000000013ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[    0.000000] Hypervisor detected: KVM
[    0.000000] tsc: Fast TSC calibration failed
[    0.000000] tsc: Unable to calibrate against PIT
[    0.000000] tsc: No reference (HPET/PMTIMER) available
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x13fdc max_arch_pfn = 0x100000
[    0.000000] MTRR: Disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WT  UC- UC  WB  WT  UC- UC  
[    0.000000] Scan for SMP in [mem 0x00000000-0x000003ff]
[    0.000000] Scan for SMP in [mem 0x0009fc00-0x0009ffff]
[    0.000000] Scan for SMP in [mem 0x000f0000-0x000fffff]
[    0.000000] found SMP MP-table at [mem 0x000f6a90-0x000f6a9f] mapped at [ffc67a90]
[    0.000000]   mpc: f6aa0-f6b80
[    0.000000] initial memory mapped: [mem 0x00000000-0x027fffff]
[    0.000000] Base memory trampoline at [b009b000] 9b000 size 16384
[    0.000000] BRK [0x0230c000, 0x0230cfff] PGTABLE
[    0.000000] RAMDISK: [mem 0x13538000-0x13fcffff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F68C0 000014 (v00 BOCHS )
[    0.000000] ACPI: RSDT 0x0000000013FE15CE 000030 (v01 BOCHS  BXPCRSDT 00000001 BXPC 00000001)
[    0.000000] ACPI: FACP 0x0000000013FE142A 000074 (v01 BOCHS  BXPCFACP 00000001 BXPC 00000001)
[    0.000000] ACPI: DSDT 0x0000000013FE0040 0013EA (v01 BOCHS  BXPCDSDT 00000001 BXPC 00000001)
[    0.000000] ACPI: FACS 0x0000000013FE0000 000040
[    0.000000] ACPI: APIC 0x0000000013FE151E 000078 (v01 BOCHS  BXPCAPIC 00000001 BXPC 00000001)
[    0.000000] ACPI: HPET 0x0000000013FE1596 000038 (v01 BOCHS  BXPCHPET 00000001 BXPC 00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] mapped APIC to         ffffc000 (        fee00000)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 319MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 13fdc000
[    0.000000]   low ram: 0 - 13fdc000
[    0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00
[    0.000000] kvm-clock: cpu 0, msr 0:13fdb001, primary cpu clock
[    0.000000] kvm-clock: using sched offset of 1978995511 cycles
[    0.000000] clocksource: kvm-clock: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[    0.000000] BRK [0x0230d000, 0x0230dfff] PGTABLE
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000001000-0x0000000013fdbfff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009efff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x0000000013fdbfff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000013fdbfff]
[    0.000000] On node 0 totalpages: 81786
[    0.000000]   Normal zone: 640 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 81786 pages, LIFO batch:15
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x608
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[    0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 0, APIC INT 02
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level)
[    0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 05, APIC ID 0, APIC INT 05
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 0, APIC INT 09
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level)
[    0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0a, APIC ID 0, APIC INT 0a
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level)
[    0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0b, APIC ID 0, APIC INT 0b
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 0, APIC INT 01
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 0, APIC INT 03
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 0, APIC INT 04
[    0.000000] ACPI: IRQ5 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 0, APIC INT 06
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 0, APIC INT 07
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 0, APIC INT 08
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ10 used by override.
[    0.000000] ACPI: IRQ11 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 0, APIC INT 0c
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 0, APIC INT 0d
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 0, APIC INT 0e
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 0, APIC INT 0f
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] mapped IOAPIC to ffffb000 (fec00000)
[    0.000000] e820: [mem 0x14000000-0xfeffbfff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on KVM
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[    0.000000] random: fast init done
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:1 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] percpu: Embedded 341 pages/cpu @c3163000 s1367808 r0 d28928 u1396736
[    0.000000] pcpu-alloc: s1367808 r0 d28928 u1396736 alloc=341*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] KVM setup async PF for cpu 0
[    0.000000] kvm-stealtime: cpu 0, msr 13165b00
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 81146
[    0.000000] Kernel command line: ip=::::vm-lkp-wsx03-openwrt-i386-31::dhcp root=/dev/ram0 user=lkp job=/lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.yaml ARCH=i386 kconfig=i386-randconfig-b0-10280741 branch=linux-devel/devel-spot-201710280538 commit=eb948c71f790f4fd27440895ca19180a78fd3016 BOOT_IMAGE=/pkg/linux/i386-randconfig-b0-10280741/gcc-5/eb948c71f790f4fd27440895ca19180a78fd3016/vmlinuz-4.14.0-rc6-00022-geb948c7 max_uptime=1500 RESULT_ROOT=/result/trinity/300s/vm-lkp-wsx03-openwrt-i386/openwrt-i386-2016-03-16.cgz/i386-randconfig-b0-10280741/gcc-5/eb948c71f790f4fd27440895ca19180a78fd3016/0 LKP_SERVER=inn debug apic=debug sysrq_always_enabled rcupdate.rcu_cpu_stall_timeout=100 net.ifnames=0 printk.devkmsg=on panic=-1 softlockup_panic=1 nmi_watchdog=panic oops=panic load_ramdisk=2 prompt_ramdisk=0 drbd.minor_count=8 systemd.log_level=err ignore_loglevel console=tty0 earlyprintk=tty
[    0.000000] sysrq: sysrq always enabled.
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (00000000:00000000)
[    0.000000] Memory: 292356K/327144K available (6137K kernel code, 1134K rwdata, 3760K rodata, 1888K init, 6428K bss, 34788K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xffe66000 - 0xfffff000   (1636 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xc47dc000 - 0xff7fe000   ( 944 MB)
[    0.000000]     lowmem  : 0xb0000000 - 0xc3fdc000   ( 319 MB)
[    0.000000]       .init : 0xb1ade000 - 0xb1cb6000   (1888 kB)
[    0.000000]       .data : 0xb15fe524 - 0xb1ac7a40   (4901 kB)
[    0.000000]       .text : 0xb1000000 - 0xb15fe524   (6137 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] ftrace: allocating 29479 entries in 58 pages
[    0.001000] Hierarchical RCU implementation.
[    0.001000] 	RCU event tracing is enabled.
[    0.001000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.001000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[    0.001000] 	RCU callback double-/use-after-free debug enabled.
[    0.001000] 	RCU debug extended QS entry/exit.
[    0.001000] 	RCU CPU stall warnings timeout set to 100 (rcu_cpu_stall_timeout).
[    0.001000] 	Tasks RCU enabled.
[    0.001000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.001000] NR_IRQS: 2304, nr_irqs: 256, preallocated irqs: 16
[    0.001000] CPU 0 irqstacks, hard=b0110000 soft=b0112000
[    0.001000] console [ttyS0] enabled
[    0.001000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.001000] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.001000] ... MAX_LOCK_DEPTH:          48
[    0.001000] ... MAX_LOCKDEP_KEYS:        8191
[    0.001000] ... CLASSHASH_SIZE:          4096
[    0.001000] ... MAX_LOCKDEP_ENTRIES:     32768
[    0.001000] ... MAX_LOCKDEP_CHAINS:      65536
[    0.001000] ... CHAINHASH_SIZE:          32768
[    0.001000]  memory used by lock dependency info: 4639 kB
[    0.001000]  per task-struct memory footprint: 2112 bytes
[    0.001000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
[    0.001000] hpet clockevent registered
[    0.002101] tsc: Detected 2260.998 MHz processor
[    0.003071] Calibrating delay loop (skipped) preset value.. 4521.99 BogoMIPS (lpj=2260998)
[    0.005101] pid_max: default: 32768 minimum: 301
[    0.006484] ACPI: Core revision 20170728
[    0.091456] ACPI: 1 ACPI AML tables successfully acquired and loaded
[    0.093543] Security Framework initialized
[    0.095484] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.096224] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.106223] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[    0.107094] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[    0.159643] Freeing SMP alternatives memory: 20K
[    0.170555] smpboot: Max logical packages: 1
[    0.171202] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.174128] enabled ExtINT on CPU#0
[    0.193352] ENABLING IO-APIC IRQs
[    0.195216] init IO_APIC IRQs
[    0.196097]  apic 0 pin 0 not connected
[    0.198128] IOAPIC[0]: Set routing entry (0-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:1)
[    0.199260] IOAPIC[0]: Set routing entry (0-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-5 -> 0x35 -> IRQ 5 Mode:1 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-10 -> 0x3a -> IRQ 10 Mode:1 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-11 -> 0x3b -> IRQ 11 Mode:1 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:1)
[    0.200000] IOAPIC[0]: Set routing entry (0-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:1)
[    0.200000]  apic 0 pin 16 not connected
[    0.200000]  apic 0 pin 17 not connected
[    0.200000]  apic 0 pin 18 not connected
[    0.200000]  apic 0 pin 19 not connected
[    0.200000]  apic 0 pin 20 not connected
[    0.200000]  apic 0 pin 21 not connected
[    0.200000]  apic 0 pin 22 not connected
[    0.200000]  apic 0 pin 23 not connected
[    0.200000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.200000] Using local APIC timer interrupts.
[    0.200000] calibrating APIC timer ...
[    0.202000] ... lapic delta = 6645034
[    0.202000] ... PM-Timer delta = 380574
[    0.202000] APIC calibration not consistent with PM-Timer: 106ms instead of 100ms
[    0.202000] APIC delta adjusted to PM-Timer: 6250076 (6645034)
[    0.202000] TSC delta adjusted to PM-Timer: 226063216 (240348711)
[    0.202000] ..... delta 6250076
[    0.202000] ..... mult: 268438720
[    0.202000] ..... calibration result: 1000012
[    0.202000] ..... CPU clock speed is 2260.0632 MHz.
[    0.202000] ..... host bus clock speed is 1000.0012 MHz.
[    0.202683] smpboot: CPU0: Intel QEMU Virtual CPU version 2.5+ (family: 0x6, model: 0x6, stepping: 0x3)
[    0.206426] Performance Events: PMU not available due to virtualization, using software events only.
[    0.210427] Hierarchical SRCU implementation.
[    0.227322] NMI watchdog: Perf event create on CPU 0 failed with -2
[    0.228131] NMI watchdog: Perf NMI watchdog permanently disabled
[    0.230518] smp: Bringing up secondary CPUs ...
[    0.231038] smp: Brought up 1 node, 1 CPU
[    0.232068] ----------------
[    0.233060] | NMI testsuite:
[    0.235068] --------------------
[    0.236054]   remote IPI:  ok  |
[    0.238032]    local IPI:  ok  |
[    0.239035] --------------------
[    0.240034] Good, all   2 testcases passed! |
[    0.241033] ---------------------------------
[    0.242057] smpboot: Total of 1 processors activated (4521.99 BogoMIPS)
[    0.248265] devtmpfs: initialized
[    0.264713] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.265154] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.269160] regulator-dummy: no parameters
[    0.272126] regulator-dummy: no parameters
[    0.274249] regulator-dummy: Failed to create debugfs directory
[    0.279901] NET: Registered protocol family 16
[    0.289223] EISA bus registered
[    0.290105] cpuidle: using governor menu
[    0.295679] ACPI: bus type PCI registered
[    0.305525] PCI: PCI BIOS revision 2.10 entry at 0xfd501, last bus=0
[    0.307063] PCI: Using configuration type 1 for base access
[    0.498781] ------------[ cut here ]------------
[    0.499097] WARNING: CPU: 0 PID: 1 at mm/hugetlb.c:2849 hugetlb_add_hstate+0x146/0x161
[    0.501039] Modules linked in:
[    0.502228] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.0-rc6-00022-geb948c7 #1
[    0.503064] task: b0138000 task.stack: b012a000
[    0.504067] EIP: hugetlb_add_hstate+0x146/0x161
[    0.505063] EFLAGS: 00210212 CPU: 0
[    0.506064] EAX: 00000000 EBX: 00000001 ECX: 00000000 EDX: 00000001
[    0.507064] ESI: ffc00000 EDI: 00000000 EBP: b012bee4 ESP: b012bed4
[    0.508065]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[    0.509065] CR0: 80050033 CR2: 00000000 CR3: 01cbe000 CR4: 00000690
[    0.510071] Call Trace:
[    0.511104]  hugetlb_init+0x58/0x4e1
[    0.512129]  ? up_write+0x1b/0x37
[    0.513096]  ? blocking_notifier_chain_register+0x56/0x60
[    0.514069]  ? mm_compute_batch_notifier+0x19/0x19
[    0.515070]  ? hugetlb_init+0x4e1/0x4e1
[    0.516095]  hugetlb_init+0x16/0x1d
[    0.517070]  do_one_initcall+0x80/0x14c
[    0.518130]  ? do_early_param+0x78/0x78
[    0.520096]  ? kernel_init_freeable+0xe7/0x17a
[    0.521191]  ? up_write+0x1b/0x37
[    0.522070]  ? kernel_init_freeable+0xe7/0x17a
[    0.523099]  kernel_init_freeable+0x107/0x17a
[    0.525064]  ? rest_init+0x115/0x115
[    0.526096]  kernel_init+0xd/0xd5
[    0.527094]  ret_from_fork+0x19/0x24
[    0.528165] Code: b3 b1 83 c4 10 31 db 81 7d f0 ff ff 3f 00 6a 00 b8 b8 58 a8 b1 0f 97 c3 31 c9 89 da e8 55 ee 5e ff 81 7d f0 ff ff 3f 00 58 76 02 <0f> ff 6a 00 31 c9 89 da b8 a0 58 a8 b1 e8 39 ee 5e ff 58 8d 65
[    0.532071] ---[ end trace 22f52a911eb8bbac ]---
[    0.533129] HugeTLB registered 4.00 MiB page size, pre-allocated 0 pages
[    0.540482] ACPI: Added _OSI(Module Device)
[    0.541163] ACPI: Added _OSI(Processor Device)
[    0.543066] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.544068] ACPI: Added _OSI(Processor Aggregator Device)
[    0.608834] ACPI: Interpreter enabled
[    0.609324] ACPI: (supports S0 S5)
[    0.610195] ACPI: Using IOAPIC for interrupt routing
[    0.612138] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.622000] ACPI: Enabled 2 GPEs in block 00 to 0F
[    0.813130] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.815102] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI]
[    0.817200] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.819167] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[    0.822189] PCI host bridge to bus 0000:00
[    0.823092] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.824093] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.826069] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.827071] pci_bus 0000:00: root bus resource [mem 0x14000000-0xfebfffff window]
[    0.828065] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.830199] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000
[    0.840583] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100
[    0.850321] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180
[    0.868067] pci 0000:00:01.1: reg 0x20: [io  0xc0c0-0xc0cf]
[    0.875267] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.876061] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.878056] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.879068] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.887423] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000
[    0.892038] pci 0000:00:01.3: quirk: [io  0x0600-0x063f] claimed by PIIX4 ACPI
[    0.893132] pci 0000:00:01.3: quirk: [io  0x0700-0x070f] claimed by PIIX4 SMB
[    0.898903] pci 0000:00:02.0: [1234:1111] type 00 class 0x030000
[    0.903158] pci 0000:00:02.0: reg 0x10: [mem 0xfd000000-0xfdffffff pref]
[    0.910165] pci 0000:00:02.0: reg 0x18: [mem 0xfebf0000-0xfebf0fff]
[    0.928136] pci 0000:00:02.0: reg 0x30: [mem 0xfebe0000-0xfebeffff pref]
[    0.935323] pci 0000:00:03.0: [8086:100e] type 00 class 0x020000
[    0.940063] pci 0000:00:03.0: reg 0x10: [mem 0xfebc0000-0xfebdffff]
[    0.943064] pci 0000:00:03.0: reg 0x14: [io  0xc000-0xc03f]
[    0.960091] pci 0000:00:03.0: reg 0x30: [mem 0xfeb80000-0xfebbffff pref]
[    0.967812] pci 0000:00:04.0: [1af4:1001] type 00 class 0x010000
[    0.972091] pci 0000:00:04.0: reg 0x10: [io  0xc040-0xc07f]
[    0.977064] pci 0000:00:04.0: reg 0x14: [mem 0xfebf1000-0xfebf1fff]
[    0.988093] pci 0000:00:04.0: reg 0x20: [mem 0xfe000000-0xfe003fff 64bit pref]
[    1.006819] pci 0000:00:05.0: [1af4:1001] type 00 class 0x010000
[    1.011065] pci 0000:00:05.0: reg 0x10: [io  0xc080-0xc0bf]
[    1.015068] pci 0000:00:05.0: reg 0x14: [mem 0xfebf2000-0xfebf2fff]
[    1.024155] pci 0000:00:05.0: reg 0x20: [mem 0xfe004000-0xfe007fff 64bit pref]
[    1.041838] pci 0000:00:06.0: [8086:25ab] type 00 class 0x088000
[    1.046068] pci 0000:00:06.0: reg 0x10: [mem 0xfebf3000-0xfebf300f]
[    1.073521] pci_bus 0000:00: on NUMA node 0
[    1.093074] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
[    1.098777] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *10 11)
[    1.105261] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10 *11)
[    1.110617] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10 *11)
[    1.113742] ACPI: PCI Interrupt Link [LNKS] (IRQs *9)
[    1.130524] ACPI: bus type USB registered
[    1.132578] usbcore: registered new interface driver usbfs
[    1.133548] usbcore: registered new interface driver hub
[    1.134454] usbcore: registered new device driver usb
[    1.137413] Linux video capture interface: v2.00
[    1.139717] EDAC MC: Ver: 3.0.0
[    1.143296] EDAC DEBUG: edac_mc_sysfs_init: device mc created
[    1.149704] PCI: Using ACPI for IRQ routing
[    1.150066] PCI: pci_cache_line_size set to 32 bytes
[    1.154184] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    1.155191] e820: reserve RAM buffer [mem 0x13fdc000-0x13ffffff]
[    1.167593] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    1.170778] clocksource: Switched to clocksource kvm-clock
[    1.253577] Warning: could not register annotated branches stats
[    1.608979] VFS: Disk quotas dquot_6.6.0
[    1.615271] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.626408] FS-Cache: Loaded
[    1.632404] pnp: PnP ACPI init
[    1.640924] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[    1.655385] pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active)
[    1.669997] pnp 00:02: Plug and Play ACPI device, IDs PNP0f13 (active)
[    1.682962] pnp 00:03: [dma 2]
[    1.689899] pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active)
[    1.705288] pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active)
[    1.721004] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.736363] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.767316] pnp: PnP ACPI: found 7 devices
[    1.825577] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    1.838511] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    1.847257] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    1.855847] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    1.865336] pci_bus 0000:00: resource 7 [mem 0x14000000-0xfebfffff window]
[    1.877907] NET: Registered protocol family 1
[    1.884367] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[    1.892823] pci 0000:00:01.0: PIIX3: Enabling Passive Release
[    1.901304] pci 0000:00:01.0: Activating ISA DMA hang workarounds
[    1.910519] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    1.922791] PCI: CLS 0 bytes, default 32
[    1.931711] Unpacking initramfs...
[   15.934363] Freeing initrd memory: 10848K
[   22.644892] Kprobe smoke test: started
[   23.166918] Kprobe smoke test: passed successfully
[   23.179943] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[   23.267792] fuse init (API version 7.26)
[   23.336308] test_printf: all 260 tests passed
[   23.342528] test_uuid: all 18 tests passed
[   23.349429] glob: 64 self-tests passed, 0 failed
[   23.360345] gpio_it87: no device
[   23.366338] gpio-mockup: probe of gpio-mockup failed with error -22
[   23.382025] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[   23.392300] ACPI: Power Button [PWRF]
[   23.402477] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[   23.412841] ACPI: Power Button [PWRF]
[   23.419721] Warning: Processor Platform Limit event detected, but not handled.
[   23.429569] Consider compiling CPUfreq support into your kernel.
[   26.951433] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[   38.456517] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[   45.504745] r3964: Philips r3964 Driver $Revision: 1.10 $
[   45.512877] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[   45.606860] 00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[   45.622872] console [ttyS0] disabled
[   45.713524] 00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[   49.033580] console [ttyS0] enabled
[   49.122758] 00:06: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[   49.219293] 00:06: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[   49.248461] Initializing Nozomi driver 2.1d
[   49.255653] SyncLink GT
[   49.259354] SyncLink GT, tty major#247
[   49.265346] SyncLink GT no devices found
[   49.270952] SyncLink serial driver $Revision: 4.38 $
[   49.379971] SyncLink serial driver $Revision: 4.38 $, tty major#246
[   49.390470] Applicom driver: $Id: ac.c,v 1.30 2000/03/22 16:03:57 dwmw2 Exp $
[   49.400742] ac.o: No PCI boards found.
[   49.406188] ac.o: For an ISA board you must supply memory and irq parameters.
[   49.416968] Non-volatile memory driver v1.3
[   49.423254] toshiba: not a supported Toshiba laptop
[   49.430387] telclk_interrupt = 0xf non-mcpbl0010 hw.
[   49.437906] smapi::smapi_init, ERROR invalid usSmapiID
[   49.445207] mwave: tp3780i::tp3780I_InitializeBoardData: Error: SMAPI is not available on this machine
[   49.457964] mwave: mwavedd::mwave_init: Error: Failed to initialize board data
[   49.467885] mwave: mwavedd::mwave_init: Error: Failed to initialize
[   49.481460] ibmasm: IBM ASM Service Processor Driver version 1.0 loaded
[   49.502557] usbcore: registered new interface driver dln2
[   49.516233] usbcore: registered new interface driver hwa-rc
[   49.524365] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   49.533892] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   49.542679] ohci-platform: OHCI generic platform driver
[   49.550815] usbcore: registered new interface driver hwa-hc
[   49.559889] usbcore: registered new interface driver wusb-cbaf
[   49.568503] usbcore: registered new interface driver cdc_acm
[   49.576210] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   49.587456] usbcore: registered new interface driver cdc_wdm
[   49.595469] usbcore: registered new interface driver mdc800
[   49.603271] mdc800: v0.7.5 (30/10/2000):USB Driver for Mustek MDC800 Digital Camera
[   49.613552] ftdi_elan: driver ftdi-elan
[   49.619319] usbcore: registered new interface driver ftdi-elan
[   49.627582] usbcore: registered new interface driver iowarrior
[   49.636562] usbcore: registered new interface driver rio500
[   49.649482] userial_init: registered 4 ttyGS* devices
[   49.657750] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[   49.678743] serio: i8042 KBD port at 0x60,0x64 irq 1
[   49.685713] serio: i8042 AUX port at 0x60,0x64 irq 12
[   49.698808] mousedev: PS/2 mouse device common for all mice
[   49.709895] usbcore: registered new interface driver appletouch
[   49.723992] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[   49.738412] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[   49.768582] usbcore: registered new interface driver aiptek
[   49.801888] usbcore: registered new interface driver pegasus_notetaker
[   49.813432] usbcore: registered new interface driver usbtouchscreen
[   49.826516] apanel: Fujitsu BIOS signature 'FJKEYINF' not found...
[   49.836950] usbcore: registered new interface driver ims_pcu
[   49.850960] usbcore: registered new interface driver i2c-tiny-usb
[   49.859770] isa i2c-pca-isa.0: Please specify I/O base
[   49.871303] lirc_dev: IR Remote Control driver registered, major 241
[   49.880025] IR RC5(x/sz) protocol handler initialized
[   49.886887] IR RC6 protocol handler initialized
[   49.893213] IR Sharp protocol handler initialized
[   49.899731] IR LIRC bridge handler initialized
[   49.906045] usbcore: registered new interface driver mceusb
[   49.914436] usbcore: registered new interface driver streamzap
[   49.922931] usbcore: registered new interface driver igorplugusb
[   49.932299] ddbridge: Digital Devices PCIE bridge driver 0.9.31intermediate-integrated, Copyright (C) 2010-17 Digital Devices GmbH
[   49.949923] cx18:  Start initialization, version 1.5.1
[   49.957575] cx18:  End initialization
[   49.962851] saa7134: saa7130/34: v4l2 driver version 0, 2, 17 loaded
[   49.973385] radio-rtrack2.0: you must set an I/O address with io=0x20f/0x30f.
[   49.983305] radio-rtrack2: probe of radio-rtrack2.0 failed with error -22
[   50.000993] radio-sf16fmr2: Unable to detect TEA575x tuner
[   50.741964] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input5
[   51.749501] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6
[   53.770859] usbcore: registered new interface driver radioshark2
[   53.791468] usbcore: registered new interface driver radio-usb-si4713
[   53.812792] usbcore: registered new interface driver radio-mr800
[   53.822001] Driver for 1-wire Dallas network protocol.
[   53.845819] usbcore: registered new interface driver DS9490R
[   53.854537] w1_f0d_init()
[   53.869931] __power_supply_register: Expected proper parent device for 'test_ac'
[   53.897734] __power_supply_register: Expected proper parent device for 'test_battery'
[   53.913383] thermal thermal_zone0: power_allocator: sustainable_power will be estimated
[   53.946208] __power_supply_register: Expected proper parent device for 'test_usb'
[   53.972911] EDAC DEBUG: i3000_init: i3000 pci_get_device fail
[   53.994916] EDAC DEBUG: x38_init: x38 pci_get_device fail
[   54.015241] platform eisa.0: Probing EISA bus 0
[   54.042883] platform eisa.0: EISA: Cannot allocate resource for mainboard
[   54.062388] platform eisa.0: Cannot allocate resource for EISA slot 1
[   54.071264] platform eisa.0: Cannot allocate resource for EISA slot 2
[   54.083514] platform eisa.0: Cannot allocate resource for EISA slot 3
[   54.103731] platform eisa.0: Cannot allocate resource for EISA slot 4
[   54.123826] platform eisa.0: Cannot allocate resource for EISA slot 5
[   54.143856] platform eisa.0: Cannot allocate resource for EISA slot 6
[   54.171267] platform eisa.0: Cannot allocate resource for EISA slot 7
[   54.190262] platform eisa.0: Cannot allocate resource for EISA slot 8
[   54.199206] platform eisa.0: EISA: Detected 0 cards
[   54.236997] ashmem: initialized
[   54.254733] FPGA DOWNLOAD --->
[   54.259169] FPGA image file name: xlinx_fpga_firmware.bit
[   54.279226] GPIO INIT FAIL!!
[   54.284441] mostcore: init()
[   54.321004] start plist test
[   54.436355] end plist test
[   54.447577] ... APIC ID:      00000000 (0)
[   54.448117] ... APIC VERSION: 01050014
[   54.448117] 0000000000000000000000000000000000000000000000000000000000000000
[   54.448117] 0000000000000000000000000000000000000000000000000000000000000000
[   54.448117] 0000000000000000000000000000000000000000000000000000000000008000
[   54.489312] number of MP IRQ sources: 15.
[   54.495207] number of IO-APIC #0 registers: 24.
[   54.501689] testing the IO APIC.......................
[   54.509301] IO APIC #0......
[   54.513584] .... register #00: 00000000
[   54.519250] .......    : physical APIC id: 00
[   54.525470] .......    : Delivery Type: 0
[   54.531303] .......    : LTS          : 0
[   54.537234] .... register #01: 00170011
[   54.542843] .......     : max redirection entries: 17
[   54.550042] .......     : PRQ implemented: 0
[   54.556357] .......     : IO APIC version: 11
[   54.562675] .... register #02: 00000000
[   54.568214] .......     : arbitration: 00
[   54.574379] .... IRQ redirection table:
[   54.579979] IOAPIC 0:
[   54.583644]  pin00, disabled, edge , high, V(00), IRR(0), S(0), physical, D(00), M(0)
[   54.594695]  pin01, enabled , edge , high, V(31), IRR(0), S(0), logical , D(01), M(1)
[   54.605648]  pin02, enabled , edge , high, V(30), IRR(0), S(0), logical , D(01), M(1)
[   54.616733]  pin03, enabled , edge , high, V(33), IRR(0), S(0), logical , D(01), M(1)
[   54.627684]  pin04, enabled , edge , high, V(34), IRR(0), S(0), logical , D(01), M(1)
[   54.638670]  pin05, disabled, level, high, V(35), IRR(0), S(0), logical , D(01), M(1)
[   54.649685]  pin06, enabled , edge , high, V(36), IRR(0), S(0), logical , D(01), M(1)
[   54.660706]  pin07, enabled , edge , high, V(37), IRR(0), S(0), logical , D(01), M(1)
[   54.671729]  pin08, enabled , edge , high, V(38), IRR(0), S(0), logical , D(01), M(1)
[   54.682837]  pin09, enabled , level, high, V(39), IRR(0), S(0), logical , D(01), M(1)
[   54.693861]  pin0a, disabled, level, high, V(3A), IRR(0), S(0), logical , D(01), M(1)
[   54.704881]  pin0b, disabled, level, high, V(3B), IRR(0), S(0), logical , D(01), M(1)
[   54.715866]  pin0c, enabled , edge , high, V(3C), IRR(0), S(0), logical , D(01), M(1)
[   54.726915]  pin0d, enabled , edge , high, V(3D), IRR(0), S(0), logical , D(01), M(1)
[   54.737898]  pin0e, enabled , edge , high, V(3E), IRR(0), S(0), logical , D(01), M(1)
[   54.748883]  pin0f, enabled , edge , high, V(3F), IRR(0), S(0), logical , D(01), M(1)
[   54.760743]  pin10, disabled, edge , high, V(00), IRR(0), S(0), physical, D(00), M(0)
[   54.771729]  pin11, disabled, edge , high, V(00), IRR(0), S(0), physical, D(00), M(0)
[   54.782774]  pin12, disabled, edge , high, V(00), IRR(0), S(0), physical, D(00), M(0)
[   54.793802]  pin13, disabled, edge , high, V(00), IRR(0), S(0), physical, D(00), M(0)
[   54.804853]  pin14, disabled, edge , high, V(00), IRR(0), S(0), physical, D(00), M(0)
[   54.816025]  pin15, disabled, edge , high, V(00), IRR(0), S(0), physical, D(00), M(0)
[   54.826950]  pin16, disabled, edge , high, V(00), IRR(0), S(0), physical, D(00), M(0)
[   54.838223]  pin17, disabled, edge , high, V(00), IRR(0), S(0), physical, D(00), M(0)
[   54.849210] IRQ to pin mappings:
[   54.853970] IRQ0 -> 0:2
[   54.857895] IRQ1 -> 0:1
[   54.861717] IRQ3 -> 0:3
[   54.865452] IRQ4 -> 0:4
[   54.869207] IRQ5 -> 0:5
[   54.873224] IRQ6 -> 0:6
[   54.876981] IRQ7 -> 0:7
[   54.880937] IRQ8 -> 0:8
[   54.884726] IRQ9 -> 0:9
[   54.888425] IRQ10 -> 0:10
[   54.892472] IRQ11 -> 0:11
[   54.896455] IRQ12 -> 0:12
[   54.900447] IRQ13 -> 0:13
[   54.904465] IRQ14 -> 0:14
[   54.908446] IRQ15 -> 0:15
[   54.912419] .................................... done.
[   54.919858] Using IPI No-Shortcut mode
[   54.925468] sched_clock: Marking stable (54925204233, 0)->(58957376875, -4032172642)
[   54.959753] Key type big_key registered
[   54.973685] BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
[   55.012570] Freeing unused kernel memory: 1888K
[   55.025374] Write protecting the kernel text: 6140k
[   55.038501] Write protecting the kernel read-only data: 3764k
[   55.184804] init: Console is alive
[   56.196555] init: - preinit -
[   56.438547] procd: - early -
[   58.216334] procd: - ubus -
[   59.235864] procd: - init -
Please press Enter to activate this console.
LKP: HOSTNAME vm-lkp-wsx03-openwrt-i386-31, MAC , kernel 4.14.0-rc6-00022-geb948c7 1, serial console /dev/ttyS0
[   82.180836] Kernel tests: Boot OK!
[   83.196727] LKP: waiting for network...
[  100.225798] /lkp/lkp/src/bin/run-lkp
[  101.240956] RESULT_ROOT=/result/trinity/300s/vm-lkp-wsx03-openwrt-i386/openwrt-i386-2016-03-16.cgz/i386-randconfig-b0-10280741/gcc-5/eb948c71f790f4fd27440895ca19180a78fd3016/0
[  101.240956] job=/lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.yaml
[  101.240956] run-job /lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.yaml
[  101.240956] skip http request: cgi-bin/lkp-jobfile-append-var?job_file=/lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.yaml&job_state=running -O /dev/null
[  102.108498] Sat Oct 28 04:20:35 UTC 2017 detected soft_timeout
[  102.196477] /lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.sh: line 3: /lkp/lkp/src/bin/event/wakeup: not found
[  102.196477] /lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.sh: line 3: /lkp/lkp/src/bin/event/wakeup: not found
[  102.196477] /lkp/lkp/src/monitors/plain/watchdog: line 131: /lkp/lkp/src/bin/event/wait: not found
[  102.196477] /lkp/lkp/src/monitors/wrapper: line 61: /lkp/lkp/src/bin/event/wait: not found
[  102.196477] /lkp/lkp/src/monitors/wrapper: line 61: /lkp/lkp/src/bin/event/wait: not found
[  102.934553] /lkp/lkp/src/monitors/oom-killer: line 23: /lkp/lkp/src/bin/event/wait: not found
[  103.000892] cat: can't open '/tmp/lkp/pid-tests': No such file or directory
[  103.060547] /lkp/lkp/src/monitors/plain/watchdog: line 131: /lkp/lkp/src/bin/event/wait: not found
[  104.136449] /lkp/lkp/src/monitors/plain/watchdog: line 131: /lkp/lkp/src/bin/event/wait: not found
[  104.136449] /lkp/lkp/src/monitors/plain/watchdog: line 131: /lkp/lkp/src/bin/event/wait: not found
[  104.136449] Terminated
[  104.136449] /lkp/lkp/src/monitors/plain/watchdog: line 131: /lkp/lkp/src/bin/event/wait: not found
[  104.136449] /lkp/lkp/src/bin/post-run: line 87: /lkp/lkp/src/bin/event/wakeup: not found
[  104.136449] /lkp/lkp/src/bin/post-run: line 88: /lkp/lkp/src/bin/event/wakeup: not found
[  104.200324] kill 768 /bin/sh /lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.sh run_job 
[  104.200324] Seeding trinity based on i386-randconfig-b0-10280741
[  104.200324] Sat Oct 28 04:20:37 UTC 2017 wait_job_finished --timeout 60
[  104.200324] Sat Oct 28 04:20:37 UTC 2017 sleep 141
[  104.200324] 2017-10-28 04:20:37 trinity -q -q -l off -s 832039 -x get_robust_list -x remap_file_pages -N 999999999 -X
[  105.200828] Trinity v1.6-640-g37eaa4d  Dave Jones <davej@codemonkey.org.uk>
[  105.200828] Using getrandom() for seeds
[  105.200828] shm:0xa76d6000-0xb3d42e64 (4 pages)
[  105.200828] [main] get_robust_list is NI_SYSCALL. Skipping
[  105.200828] [main] Marking syscall get_robust_list (312) as to be disabled.
[  105.200828] [main] Marking syscall remap_file_pages (257) as to be disabled.
[  105.200828] [main] Using user passed random seed: 832039
[  105.200828] [main] Kernel was tainted on startup. Will ignore flags that are already set.
[  105.200828] Marking all syscalls as enabled.
[  105.200828] [main] Disabling syscalls marked as disabled by command line options
[  105.200828] [main] Marked syscall remap_file_pages (257) as deactivated.
[  105.200828] [main] Marked syscall get_robust_list (312) as deactivated.
[  105.200828] [main] Enabled 377 syscalls. Disabled 3 syscalls.
[  105.539401] kill 770 cat /proc/kmsg 
[  106.713467] wait for background monitors: 772 oom-killer
[  111.073687] skip http request: cgi-bin/lkp-jobfile-append-var?job_file=/lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.yaml&job_state=soft_timeout -O /dev/null
[  111.361033] sysrq: SysRq : Emergency Sync
[  111.380640] Emergency Sync complete
[  111.408796] sysrq: SysRq : Resetting

Elapsed time: 120

initrds=(
	/osimage/openwrt/openwrt-i386-2016-03-16.cgz
	/lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.cgz
	/lkp/lkp/lkp-i386.cgz
	/osimage/pkg/static/trinity-i386.cgz
	/pkg/linux/i386-randconfig-b0-10280741/gcc-5/eb948c71f790f4fd27440895ca19180a78fd3016/modules.cgz
)

cat "${initrds[@]}" > /fs/sdc1/initrd-vm-lkp-wsx03-openwrt-i386-31

kvm=(
	qemu-system-i386
	-enable-kvm
	-kernel /pkg/linux/i386-randconfig-b0-10280741/gcc-5/eb948c71f790f4fd27440895ca19180a78fd3016/vmlinuz-4.14.0-rc6-00022-geb948c7
	-initrd /fs/sdc1/initrd-vm-lkp-wsx03-openwrt-i386-31
	-m 320
	-smp 1
	-device e1000,netdev=net0
	-netdev user,id=net0
	-boot order=nc
	-no-reboot
	-watchdog i6300esb
	-watchdog-action debug
	-rtc base=localtime
	-drive file=/fs/sdc1/disk0-vm-lkp-wsx03-openwrt-i386-31,media=disk,if=virtio
	-drive file=/fs/sdc1/disk1-vm-lkp-wsx03-openwrt-i386-31,media=disk,if=virtio
	-pidfile /dev/shm/kboot/pid-vm-lkp-wsx03-openwrt-i386-31
	-serial file:/dev/shm/kboot/vm-lkp-wsx03-openwrt-i386-31/serial
	-serial file:/dev/shm/kboot/vm-lkp-wsx03-openwrt-i386-31/kmsg
	-daemonize
	-display none
	-monitor null
)

append=(
	ip=::::vm-lkp-wsx03-openwrt-i386-31::dhcp
	root=/dev/ram0
	user=lkp
	job=/lkp/scheduled/vm-lkp-wsx03-openwrt-i386-31/trinity-300s-openwrt-i386-2016-03-16.cgz-eb948c71f790f4fd27440895ca19180a78fd3016-20171028-54973-fdsy20-0.yaml
	ARCH=i386
	kconfig=i386-randconfig-b0-10280741
	branch=linux-devel/devel-spot-201710280538
	commit=eb948c71f790f4fd27440895ca19180a78fd3016
	BOOT_IMAGE=/pkg/linux/i386-randconfig-b0-10280741/gcc-5/eb948c71f790f4fd27440895ca19180a78fd3016/vmlinuz-4.14.0-rc6-00022-geb948c7
	max_uptime=1500
	RESULT_ROOT=/result/trinity/300s/vm-lkp-wsx03-openwrt-i386/openwrt-i386-2016-03-16.cgz/i386-randconfig-b0-10280741/gcc-5/eb948c71f790f4fd27440895ca19180a78fd3016/0
	LKP_SERVER=inn
	debug
	apic=debug
	sysrq_always_enabled
	rcupdate.rcu_cpu_stall_timeout=100
	net.ifnames=0
	printk.devkmsg=on
	panic=-1
	softlockup_panic=1
	nmi_watchdog=panic
	oops=panic
	load_ramdisk=2
	prompt_ramdisk=0
	drbd.minor_count=8
	systemd.log_level=err
	ignore_loglevel
	console=tty0
	earlyprintk=ttyS0,115200
	console=ttyS0,115200
	vga=normal
	rw
	drbd.minor_count=8
)

"${kvm[@]}" -append "${append[*]}"
