On Friday, August 24, 2012, Jaehoon Chung <jh80.ch...@samsung.com> wrote:
> Hi Seungwon,
>
> On 08/24/2012 12:55 PM, Seungwon Jeon wrote:
> > Hi Jaehoon,
> >
> > On Thursday, August 23, 2012, Jaehoon Chung <jh80.ch...@samsung.com> wrote:
> >> To avoid glitches in the card clock output,
> >> need to check whether card is busy or not.
> > Could you describe the problem more?
> synopsys spec is mentioned. (7.1 Software/Hardware Restrictions)
> "Before disabling clock, ensure that card is not busy due to any previous
> data command."
>
> > In which situation did you meet this?
> At specific board, i found the problem that didn't inform ciu.
> (It didn't produce always.)
> At that time, i checked the status register whether card is busy or not.
> (Start bit of CMD register is cleared, but card is busy.)
> Current code didn't check the card status. Just check whether the start-bit
> cleared.
> host regard that command is completed, will send the next command.
> But next command didn't issue because Card is busy.
> This patch can prevent this situation.
>
> If you have any comment or opinion, please let me know. it's great help to me
If you know a point in time, we can reproduce it.
>
> Best Regards,
> Jaehoon Chung
> >
> > Thanks,
> > Seungwon Jeon
> >>
> >> Signed-off-by: Jaehoon Chung <jh80.ch...@samsung.com>
> >> Signed-off-by: Kyungmin Park <kyungmin.p...@samsung.com>
> >> ---
> >> drivers/mmc/host/dw_mmc.c | 30 ++++++++++++++++++++++++------
> >> drivers/mmc/host/dw_mmc.h | 1 +
> >> 2 files changed, 25 insertions(+), 6 deletions(-)
> >>
> >> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> >> index 36f98c0..8bef3c2 100644
> >> --- a/drivers/mmc/host/dw_mmc.c
> >> +++ b/drivers/mmc/host/dw_mmc.c
> >> @@ -623,6 +623,27 @@ static void mci_send_cmd(struct dw_mci_slot *slot,
> >> u32 cmd, u32 arg)
> >> cmd, arg, cmd_status);
> >> }
> >>
> >> +static void dw_mci_inform_ciu(struct dw_mci_slot *slot)
> >> +{
> >> + struct dw_mci *host = slot->host;
> >> + unsigned long timeout = jiffies + msecs_to_jiffies(500);
> >> + u32 ctrl, status;
> >> +
> >> + do {
> >> + status = mci_readl(host, STATUS);
> >> + if (!(status & SDMMC_DATA_BUSY))
> >> + break;
> >> + ctrl = mci_readl(host, CTRL);
> >> + ctrl |= SDMMC_CTRL_RESET;
> >> + mci_writel(host, CTRL, ctrl);
> >> + } while (time_before(jiffies, timeout));
> >> +
> >> + if (status & SDMMC_DATA_BUSY)
> >> + dev_err(&slot->mmc->class_dev,"Card is busy..!\n");
> >> +
> >> + mci_send_cmd(slot, SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
> >> +}
> >> +
> >> static void dw_mci_setup_bus(struct dw_mci_slot *slot)
> >> {
> >> struct dw_mci *host = slot->host;
> >> @@ -650,15 +671,13 @@ static void dw_mci_setup_bus(struct dw_mci_slot
> >> *slot)
> >> mci_writel(host, CLKSRC, 0);
> >>
> >> /* inform CIU */
> >> - mci_send_cmd(slot,
> >> - SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
> >> + dw_mci_inform_ciu(slot);
> >>
> >> /* set clock to desired speed */
> >> mci_writel(host, CLKDIV, div);
> >>
> >> /* inform CIU */
> >> - mci_send_cmd(slot,
> >> - SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
> >> + dw_mci_inform_ciu(slot);
> >>
> >> /* enable clock; only low power if no SDIO */
> >> clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
> >> @@ -667,8 +686,7 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot)
> >> mci_writel(host, CLKENA, clk_en_a);
> >>
> >> /* inform CIU */
> >> - mci_send_cmd(slot,
> >> - SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
> >> + dw_mci_inform_ciu(slot);
> >>
> >> host->current_speed = slot->clock;
> >> }
> >> diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
> >> index 15c27e1..b6a1a78 100644
> >> --- a/drivers/mmc/host/dw_mmc.h
> >> +++ b/drivers/mmc/host/dw_mmc.h
> >> @@ -127,6 +127,7 @@
> >> #define SDMMC_CMD_INDX(n) ((n) & 0x1F)
> >> /* Status register defines */
> >> #define SDMMC_GET_FCNT(x) (((x)>>17) & 0x1FFF)
> >> +#define SDMMC_DATA_BUSY BIT(9)
> >> /* Internal DMAC interrupt defines */
> >> #define SDMMC_IDMAC_INT_AI BIT(9)
> >> #define SDMMC_IDMAC_INT_NI BIT(8)
> >> --
> >> 1.7.4.1
> >> --
> >> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> >> the body of a message to majord...@vger.kernel.org
> >> More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> > the body of a message to majord...@vger.kernel.org
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
