synopsys spec is mentioned. (7.1 Software/Hardware Restrictions)
"Before disabling clock, ensure that card is not busy due to any previous data
command."
At specific board, i found the problem that didn't inform ciu.
(It didn't produce always.)
At that time, i checked the status register whether card is busy or not.
(Start bit of CMD register is cleared, but card is busy.)
Current code didn't check the card status. Just check whether the start-bit
cleared.
host regard that command is completed, will send the next command.
But next command didn't issue because Card is busy.
This patch can prevent this situation.
Signed-off-by: Jaehoon Chung <jh80.ch...@samsung.com>
---
drivers/mmc/host/dw_mmc.c | 27 +++++++++++++++++++++------
drivers/mmc/host/dw_mmc.h | 1 +
2 files changed, 22 insertions(+), 6 deletions(-)
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 36f98c0..e30d3ed 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -623,6 +623,24 @@ static void mci_send_cmd(struct dw_mci_slot *slot, u32
cmd, u32 arg)
cmd, arg, cmd_status);
}
+static void dw_mci_inform_ciu(struct dw_mci_slot *slot)
+{
+ struct dw_mci *host = slot->host;
+ unsigned long timeout = jiffies + msecs_to_jiffies(10);
+ u32 ctrl, status;
+
+ do {
+ status = mci_readl(host, STATUS);
+ if (!(status & SDMMC_DATA_BUSY))
+ break;
+ ctrl = mci_readl(host, CTRL);
+ ctrl |= SDMMC_CTRL_RESET;
+ mci_writel(host, CTRL, ctrl);
+ } while (time_before(jiffies, timeout));
+
+ mci_send_cmd(slot, SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
+}
+
static void dw_mci_setup_bus(struct dw_mci_slot *slot)
{
struct dw_mci *host = slot->host;
@@ -650,15 +668,13 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot)
mci_writel(host, CLKSRC, 0);
/* inform CIU */
- mci_send_cmd(slot,
- SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
+ dw_mci_inform_ciu(slot);
/* set clock to desired speed */
mci_writel(host, CLKDIV, div);
/* inform CIU */
- mci_send_cmd(slot,
- SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
+ dw_mci_inform_ciu(slot);
/* enable clock; only low power if no SDIO */
clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
@@ -667,8 +683,7 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot)
mci_writel(host, CLKENA, clk_en_a);
/* inform CIU */
- mci_send_cmd(slot,
- SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
+ dw_mci_inform_ciu(slot);
host->current_speed = slot->clock;
}
diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
index 15c27e1..b6a1a78 100644
--- a/drivers/mmc/host/dw_mmc.h
+++ b/drivers/mmc/host/dw_mmc.h
@@ -127,6 +127,7 @@
#define SDMMC_CMD_INDX(n) ((n) & 0x1F)
/* Status register defines */
#define SDMMC_GET_FCNT(x) (((x)>>17) & 0x1FFF)
+#define SDMMC_DATA_BUSY BIT(9)
/* Internal DMAC interrupt defines */
#define SDMMC_IDMAC_INT_AI BIT(9)
#define SDMMC_IDMAC_INT_NI BIT(8)
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
