Dears the configuration register value is 0x3922
which means i just changed the baud rate to 115200
anyway what i am looking for , is there any IOS image that supports the boot
config command on the Cisco 2621XM
Thanks
> Date: Tue, 1 Jun 2010 11:45:58 -0700
> From: dharmach...@gmail.com
> To: jf
Nope it is on a different subinterface:
interface Loopback0
ip address 172.16.0.1 255.255.255.255
!
interface FastEthernet0/0
description 3560
no ip address
duplex auto
speed auto
!
interface FastEthernet0/0.200
encapsulation dot1Q 200
ip address 10.0.0.1 255.255.255.0
ip pim sparse-mode
On Fri, 28 May 2010, Rick Kunkel wrote:
Heya folks...
I've connected a switch of mine to a provider's switch, and I'm getting
CDP-4-NATIVE_VLAN_MISMATCH warnings... but everything works fine.
Is this just a harmless warning? I'm not doing any VLANs with them. Their
connection is going int
On Fri, 28 May 2010 16:41:16 -0700, Rick Kunkel wrote:
I've connected a switch of mine to a provider's switch, and I'm getting
CDP-4-NATIVE_VLAN_MISMATCH warnings... but everything works fine.
Is this just a harmless warning? I'm not doing any VLANs with them.
Their connection is going i
I've not sync. hardware clock with NTP server. I see this '70 on all the
CSM in our network, even on cisco docs sample outputs.
Thanks.
Sent via Blackberry®
-Original Message-
From: Rizal
Date: Tue, 1 Jun 2010 20:49:59
To:
Subject: Re: [c-nsp] sh module csm 2 probe real
Have you try
Have you try this command on the global config.
router(config)#ntp update-calendar
Regards,
On May 27, 3:30 pm, Sony Scaria wrote:
> hello group,
>
> Can someone please explain me why it is showing "13:36:47 gmt 06/14/70".
> I've searched a lot, but i couldnt find any explanation.
> btw, my sw
Hi there!
> The 3550 Switch doesn't support egress policing or shaping at less then line
> rate.
There's only one case when you can *DO* egress policing on
cat3550 platform but you're restricted to use *ONLY*:
-- class-map w/ "match ip dscp"
-- action = "police"
Dear List,
I have just installed an Out Of Band network in case of major crashes for
our company.
The architecture is the following :
3 Cisco 2600 routers gearded with async NM32 modules and octal cables. Each
console is connected to the console port of my backbone routers.
The routers are NATe
On Tue, Jun 1, 2010 at 16:14, Rens wrote:
> I have tested this setup with a different 7206VXR running
> c7200-adventerprisek9-mz.124-4.T1.bin and I have the same problem.
Are you trying to run PIM on the same interface that you have xconnect
configured on? Can you please post the relevant configu
The 3550 Switch doesn't support egress policing or shaping at less then line
rate.
The only way I've been successful in limiting traffic outbound on this
platform is by using an 'aggregate policer' evaluated on ingress for ports
that will ultimately send traffic out the port you want to limit traf
On 6/1/2010 9:00 AM, cisco-nsp-requ...@puck.nether.net wrote:
Send cisco-nsp mailing list submissions to
cisco-nsp@puck.nether.net
To subscribe or unsubscribe via the World Wide Web, visit
https://puck.nether.net/mailman/listinfo/cisco-nsp
or, via email, send a message with sub
When the 2 PE routers (IBGP) connect via their loopback address,
everything works fine. Multicast source R7 can send data to receiver R8
However as soon as I use the physical address, BGP comes up, icmp is ok, but
no more multicast trafffic.
Setup:
CE R7 - PE R3 --- MPLS -- PE R6 --- CE R8
R7 /
I have tested this setup with a different 7206VXR running
c7200-adventerprisek9-mz.124-4.T1.bin and I have the same problem.
-Original Message-
From: Leonardo Gama Souza [mailto:leonardo.so...@nec.com.br]
Sent: mardi 1 juin 2010 16:26
To: Rens
Cc: cisco-nsp@puck.nether.net
Subject: RES: [
On 6/1/10 8:31 AM, j.vaningensche...@utwente.nl wrote:
> Hi,
>
>> Anybody have any experience with FlexOptic? Their website seems a
>> little crazy: http://www.flexoptix.net
>>
>> But they claim to have an SFP/GBIC programmer, plus tunable optics,
>> which is what interests me.
>
> We just decide
#show diagnostics result module 1 detail
should help you identify which GOLD test has failed.
#hw-module module 1 reset
resets power to the module
On Tue, Jun 1, 2010 at 3:56 PM, Renelson Panosky wrote:
> Thank you, same thing Cisco suggest
>
> On Tue, Jun 1, 2010 at 9:45 AM, Dmitry Valdov wr
Does that device support the FORMAT command to redo the NVRAM?
Jeff
On Jun 1, 2010, at 10:55 , Mohammad Khalil wrote:
> The issue is that i can start the router and the IOS is loaded successfully
> when i type anything and save it such as a hostname or interface description
> and reload the rou
Hi,
Do a "sh ver"
What is the Configuration register value?
Regards,
laci
2010-06-01 16:55 keltezéssel, Mohammad Khalil írta:
The issue is that i can start the router and the IOS is loaded successfully
when i type anything and save it such as a hostname or interface description
and reload
Hi,
> Anybody have any experience with FlexOptic? Their website seems a
> little crazy: http://www.flexoptix.net
>
> But they claim to have an SFP/GBIC programmer, plus tunable optics,
> which is what interests me.
We just decided to order the starter kit. If the first tests with the
included 1G
should be something like this:
l2tp-class L2TPVPN
hidden
authentication
password 1a2b3c4b5d
!
pseudowire-class L2TPVPN-PW
encapsulation l2tpv2
protocol l2tpv2 L2TPVPN
ip pmtu
ip tos reflect
!
interface Virtual-PPP1
ip address negotiated
ip mtu 1460
ip tcp adjust-mss 1420
no cdp enable
The issue is that i can start the router and the IOS is loaded successfully
when i type anything and save it such as a hostname or interface description
and reload the router i find the router back to scratch which means that there
is no configuration file saved
Subject: Re: [c-nsp] RES: Loa
I am guessing you are in ROM MON mode and need to get the IOS loaded and then
the config.
I believe you need to do...
boot system flash (any sub device goes here)
Jeff
On Jun 1, 2010, at 09:45 , Mohammad Khalil wrote:
>
> The current IOS is c2600-advipservicesk9-mz.124-18e.bin
>
> i tried
In the configuration guide for the IOS version.
-Mensagem original-
De: Rens [mailto:r...@autempspourmoi.be]
Enviada em: terça-feira, 1 de junho de 2010 10:13
Para: Leonardo Gama Souza
Cc: cisco-nsp@puck.nether.net
Assunto: RE: [c-nsp] IPv4 Multicast
I only have looked at the bug toolkit
So try to set in the ROM Monitor:
> CONFIG_FILE=flash:startup-config
> sync
> reset
De: Mohammad Khalil [mailto:eng_m...@hotmail.com]
Enviada em: terça-feira, 1 de junho de 2010 10:45
Para: Leonardo Gama Souza; cisco-nsp@puck.nether.net
Assunto: RE: RES: [c
Just invert the direction of the policy on the interface:
interface FastEthernet0/17
service-policy output MyPolicy
Ziv
From: Mohammad Khalil [mailto:eng_m...@hotmail.com]
Sent: Tuesday, June 01, 2010 4:50 PM
To: Ziv Leyes; cisco-nsp@puck.nether.net
Subject: RE: [c-nsp] Limit port usage on a ci
Thank you, same thing Cisco suggest
On Tue, Jun 1, 2010 at 9:45 AM, Dmitry Valdov wrote:
>
>
> On Tue, 1 Jun 2010, Anton Turygin wrote:
>
> On Tue, 1 Jun 2010, Dmitry Valdov wrote:
>>
>> Hello,
>>>
>>> This is the answer:
>>> ==
>>> 1WS-X6148A-GE-45AF 112.56 2.68 - - onoff
what could i do to limit the outbound traffic not the inbound traffic ?
> From: z...@gilat.net
> To: cisco-nsp@puck.nether.net
> Date: Tue, 1 Jun 2010 15:59:43 +0300
> Subject: Re: [c-nsp] Limit port usage on a cisco 3550
>
> This an example of how I do it:
>
> conf t
> mls qos
> !
> class-map
On Tue, 1 Jun 2010, Anton Turygin wrote:
On Tue, 1 Jun 2010, Dmitry Valdov wrote:
Hello,
This is the answer:
==
1WS-X6148A-GE-45AF 112.56 2.68 - - onoff (Diagnostic
Failure)
==
Try to reinsert the card. If it doesn't help, replace it.
He had problems with module 6.
The current IOS is c2600-advipservicesk9-mz.124-18e.bin
i tried more than one IOS image and i am not able to find the right image
because when i issue the command boot , see the output below
Router(config)#boot ?
bootstrap Bootstrap image file
host Router-specific config file
networ
Have you looked for well known restrictions for L2TPv3/PIM/IGMP Snooping
working altogether in your current IOS version?
___
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.net
It is supposed to work...
Did you issue the following command?
boot config disk0:startup-config nvbypass
Which version are you using?
-Mensagem original-
De: cisco-nsp-boun...@puck.nether.net
[mailto:cisco-nsp-boun...@puck.nether.net] Em nome de Mohammad Khalil
Enviada em: terça-feir
On Tue, 1 Jun 2010, Dmitry Valdov wrote:
Hello,
This is the answer:
==
1WS-X6148A-GE-45AF 112.56 2.68 - - onoff (Diagnostic
Failure)
==
Try to reinsert the card. If it doesn't help, replace it.
He had problems with module 6. And now it is module 1. Seems strange for
m
Hello,
What does command "show power" show?
On Tue, 1 Jun 2010, Renelson Panosky wrote:
Hello All
One of my blade is not powering up but i can't remember the command to power
it back up. Can some one please help me ? The sho mod command is below.
#sho mod
Mod Ports Card Type
Hello,
This is the answer:
==
1WS-X6148A-GE-45AF 112.56 2.68 - - onoff (Diagnostic
Failure)
==
Try to reinsert the card. If it doesn't help, replace it.
On Tue, 1 Jun 2010, Renelson Panosky wrote:
COSW02-2165-FRED#sho ver
Cisco IOS Software, s3223_rp Software (s3223_rp
COSW02-2165-FRED#sho ver
Cisco IOS Software, s3223_rp Software (s3223_rp-IPBASEK9-M), Version
12.2(33)SXH6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Thu 15-Oct-09 11:50 by prod_rel_team
ROM: System Bootstrap,
I only have looked at the bug toolkit, where can I find those restrictions?
-Original Message-
From: Leonardo Gama Souza [mailto:leonardo.so...@nec.com.br]
Sent: mardi 1 juin 2010 15:06
To: Rens
Cc: cisco-nsp@puck.nether.net
Subject: RES: [c-nsp] IPv4 Multicast
Have you looked for well k
This an example of how I do it:
conf t
mls qos
!
class-map match-all MyClass
match ip dscp 0
policy-map MyPolicy
class MyClass
police 2000 375 exceed-action drop
!
interface FastEthernet0/17
service-policy input MyPolicy
!
end
Hope this helps
Ziv
-Original Message-
From
Hello,
Please show the output of "show ver" command.
On Tue, 1 Jun 2010, Renelson Panosky wrote:
Hello All
One of my blade is not powering up but i can't remember the command to power
it back up. Can some one please help me ? The sho mod command is below.
#sho mod
Mod Ports Card Type
Hi,
I was wondering, what real life performance can one expect from an NPE
G1, considering mostly vanilla IP routing/forwarding? (no ACLs, no VPNs,
running CEF and MPLS VRFs, OSPF/iBGP for routing protocol, and utilizing
the integrated Gbit interfaces as well as 1-2 STM1 PAs on the 7200 VXR
chassi
01.06.2010 15:42, Renelson Panosky пишет:
Power enable module 6 is not working
Please, show output of 'show power' command.
May be you need more powerfull power supply.
On Tue, Jun 1, 2010 at 8:30 AM, Artyom Viklenkowrote:
01.06.2010 15:18, Renelson Panosky пишет:
Hello All
One of my b
Power enable module 6 is not working
On Tue, Jun 1, 2010 at 8:30 AM, Artyom Viklenko wrote:
> 01.06.2010 15:18, Renelson Panosky пишет:
>
> Hello All
>>
>> One of my blade is not powering up but i can't remember the command to
>> power
>> it back up. Can some one please help me ? The sho mod com
01.06.2010 15:18, Renelson Panosky пишет:
Hello All
One of my blade is not powering up but i can't remember the command to power
it back up. Can some one please help me ? The sho mod command is below.
may be:
power enable module 6
#sho mod
Mod Ports Card Type
Hello,
Hope thsi helps :
http://cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a008015bfa8.shtml#use
Y.
2010/6/1 Renelson Panosky
> Hello All
>
> One of my blade is not powering up but i can't remember the command to
> power
> it back up. Can some one please help me ? Th
Hello All
One of my blade is not powering up but i can't remember the command to power
it back up. Can some one please help me ? The sho mod command is below.
#sho mod
Mod Ports Card Type Model Serial
No.
--- - --
hi all
i have Cisco 2621XM
the NVRAM is corrupted and i want to load the configuration file from flash
i looked for the command boot config
but i cannot find the appropriate image for the router to do this
Thanks
__
Does anyone know the figures according to a user set MTU ? like for
jumbo frames for instance ?
To the best of my knowledge (a few years experience) PPS is the be all
and end all, essentially everything is in deciding where the packet goes
not how much data it contains. So PPS is king, MTU add
Hi
I search to know if i can limit at 20 Mbits the usage of a Fe Port
on a Cisco 3550 catalyst EMI ?
The 3550 are used in Level 2, not Level 3.
Thanks for your help
Stephane
___
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/
Hello Ian,
I have been keeping that doc router performance doc with me like a bible but
still.
Exept that the figures that are given are calculated like this :
"All numbers are for IP packets only - no IPX/AT/DEC, etc. - Mbps calculated
by pps * 64bytes * 8bits/byte; except
for 12000 (Engines 0,
I'd recommend using console access as a "last resort" way of accessing your
device in case no remote access is possible, in most cases when there are some
connectivity failures your device can't authenticate with tacacs, right? So you
should have a failover to a local user/password.
In the conso
You can use the "reversible" feature in your nat settings instead of "overload"
but as fas as I know the "reversible" keyword is only applicable when you are
using route-maps to check which inside addresses shall be translated.
For example:
ip nat pool NAT 192.0.2.10 192.0.2.10 netmask 255.255.2
On 1/06/2010 1:15 AM, Mackinnon, Ian wrote:
With a following wind :-
7200-NPE-G1 1,018,000 PPS 521.22 Mbps
7200-NPE-G2 2,000,000 PPS 1,024.00 Mbps
So give or take a G1 ~500M, G2 1G bps
Keep in mind the PPS is what matters not the bps (well not as much).
-James.
On 1/06/2010 12:23 AM, Nick Celebic wrote:
I tried tagging 600Mb worth of traffic on a G1, and that brought the
routers to it's knees with 100% CPU. Given that all QoS in a 7200 is
done in software, are there any ballpark numbers used to calculate how
much throughput you can get using QoS on the
Have you considered L2TPv3?
Oliver
___
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
Not tried it on a vss, but have used it on plain 6500.
Works a treat, don't forget the "expand" option to a show ip access-list
to see whats going on
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/con
figuration/guide/acl.html
Router(config)# object-group ip address myAG
Ro
i have a leased line customer who wants to encrypt the data from my side and
his side and the connection is MW terminated to Ethernet interfaces
any ideas ?
_
Your E-mail and More On-the-Go.
Arne,
Did you check:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/con
figuration/guide/acl.html#wpmkr1096071
Arie
-Original Message-
From: cisco-nsp-boun...@puck.nether.net
[mailto:cisco-nsp-boun...@puck.nether.net] On Behalf Of Arne Larsen /
Region Nordjylland
Se
Hi All.
I'm trying to use addrgroup in access-list on a vss setup, but I can't seem to
get it working.
If I setup an statement in a access-list it just ignores it.
Has someone any doc. about this.
/Arne
___
cisco-nsp mailing list cisco-nsp@puck.nethe
56 matches
Mail list logo
