On 05/08/2010 11:45 PM, Donnie Timmons wrote:
> When using a 5I20 and a 7i33 with encoder feedback. Witch parameter control
> the scaling of encoder counts to units in my case inches. "INPUT_SCALE =
> 81920" from the ini file or "setp hm2_[HOSTMOT2](BOARD).0.encoder.02.scale
> 2000" from the hal f
>In general, the HAL file reads values from the INI file. It is what
>the HAL file does that matters.
>In the sample file I have just looked at the line in the HAL is
>setp hm2_[HOSTMOT2](BOARD).0.encoder.02.scale [AXIS_2]INPUT_SCALE
>which will read the value from the INI file, in your case t
I agree nice work. Thanks!
I pulled the tar.gz file, compiled it and it is running very nicely on
Ubuntu 9.10. :-)
I'll test it on a machine tomorrow.
Dave
On 5/9/2010 3:20 PM, Sven Wesley wrote:
> 2010/5/9 Jeff Epler
>
>
>> I'm pleased to announce the first stable release of the
From what I have seen having the line NML_FILE = emc.nml causes an
error on 2.4 and later, while it is required in 2.3.5 and earlier.
So yes. That line should be removed from all of the example .ini files
as far as I can tell.
Dave
On 5/9/2010 8:46 PM, Cal Grandy wrote:
> OK, OK Follo
OK, OK Follow directions, The inifiles needed updating.
Thanks to those who go before! Must removal of the NML_FILE = emc.nml.
line be done manually for all the examples?
Cal
On Sun, 2010-05-09 at 20:06 -0400, Cal Grandy wrote:
> On Sun, 2010-05-09 at 14:01 -0500, Jeff Epler wrote:
> > I
On 9 May 2010 23:52, Ian W. Wright wrote:
>
> Is it possible to configure a stepper as a spindle motor and
> if so - how?
If it has the power to be useful, then it is just a case of
configuring a stepgen in hal in velocity mode.
The sensible way to do it is probably to keep two completely sepera
On Sun, 2010-05-09 at 14:01 -0500, Jeff Epler wrote:
> I'm pleased to announce the first stable release of the 2.4 series, emc
> 2.4.0. This version has many new features compared to 2.3.5.
I have just installed the 2.4 version.
The sample configurations in "My Configurations/stepper, Cause an
Is it possible to configure a stepper as a spindle motor and
if so - how? I have a little lathe set up as a rotary axis
with stepper motor drive and it would be very useful if I
could arrange it so that the spindle optionally worked
(using another config file) as a normal lathe spindle. I
have
Hello, all,
I just added a DAC for spindle speed control to my Bridgeport. For
years, I just had forward and reverse contact closures to the VFD and a
manual speed pot. Now, I have a DAC channel from EMC to the VFD. I can
start the spindle with an MDI entry like M03 S2500, but when I try to
Neil Baylis wrote:
> On Sat, May 8, 2010 at 8:37 PM, Jon Elson wrote:
>
>> At these sorts of speeds, you may need to up the servo sampling rate
>> quite a bit. You can easily go to 2 KHz,
>> and with a good PCI parallel port card, you should be able to go to 4 or
>> 5 KHz.
>>
>>
>
> Why d
2010/5/9 Jeff Epler
> I'm pleased to announce the first stable release of the 2.4 series, emc
> 2.4.0. This version has many new features compared to 2.3.5.
>
>
Hat off to all involved!
Regards,
Sven
--
___
I'm putting a small H-bridge together using TIP121/126 to replace a SN754410NE.
The schematic I'm following didn't list any values for the flyback diodes. In
fact some examples left them out. I know that when this circuit is in use it
switches from full forward to full reverse with no ramping. T
I'm pleased to announce the first stable release of the 2.4 series, emc
2.4.0. This version has many new features compared to 2.3.5.
The new packages will soon be available for Ubuntu 8.04 "Hardy Heron" in
the package repositories. Because this package is incompatible with emc
2.3.5 in several m
Hi Folks,
Here's another simple python script for Axis, which generates spirograph type
curves. If anybody is interested in this, the details are on my site at:
http://www.andyshelley.co.uk/axisfarris/index.php
Unfortunately, I no longer have my cnc router, so if any kind person could
spare
On 9 May 2010 06:45, Donnie Timmons wrote:
>
> When using a 5I20 and a 7i33 with encoder feedback. Witch parameter control
> the scaling of encoder counts to units in my case inches. "INPUT_SCALE =
> 81920" from the ini file or "setp hm2_[HOSTMOT2](BOARD).0.encoder.02.scale
> 2000" from the hal f
15 matches
Mail list logo
