Hello,
I prefered to kill the chassis cluster, and I rebuilt it.
I retrieved my routing process
I can ping all the network.
Thanks for your help.
Roland DROUAL
- Mail Original -
De: "Tim Eberhard"
À: "Scott T. Cameron"
Cc: "Roland Droual" , juniper-nsp
Hello the list,
I solve most of problems to ping from my SRX cluster.
But now, I have a new problem, because I did a lot of changes:
I don't have routing process on the cluster of site B.
toto@BA-SRX650-01# show chassis cluster
reth-count 6;
redundancy-gro
Hello the list,
I solve most of problems to ping from my SRX cluster.
- In first, my provider gave me another range IP @, because the first was
wrong. So I can ping from my DMZ (with public @);
- In Second, I put my NAT rules (which I forgot), so I can ping from a node
from INSIDE network;
Hello the list,
I solve most of problems to ping from my SRX cluster.
- In first, my provider gave me another range IP @, because the first was
wrong. So I can ping from my DMZ (with public @);
- In Second, I put my NAT rules (which I forgot), so I can ping from a node
from INSIDE network;
-
ime, I began to ping nodes on internet from the DMZ.
The range 193.48.41.194/29 doesn't need source nat rule.
Maybe this range is not routed by my provider. I must verify that ... but I
don't think it's the good answer.
I think I forgot something else in the SRX configuration.
on SRX650
(195.221.125.206), but I can't ping the next-hop (195.221.125.205) for
the default route.
Can you help me ?
Thanks for your help
Roland DROUAL
This is my config:
===
toto@AS-SRX650-01# run show configuration
...
reth0 {
descript
Thank you.
I typed:
set chassis cluster reth-count 5
and my config is right now.
I lost my chassis-cluster 2 weeks ago with 5 reth, and I don't know why
the new config was with reth-count = 2
It's OK now,
Thank you
Roland DROUAL
Le 11/06/2012 14:08, Clay Haynes a écrit :
Can
I want to add:
The interface reth2 is connected to an interface ge-0/0/21 on a switch
EX4200.
The interface is in trunk mode. (it's the same if the interface is in
access mode).
This interface ge-0/0/21 is UP.
Thanks for your help
Roland DROUAL
titi@AS-EX4200-01# show interfaces ge-0
Hello the List,
I have a problem with an redundant interface reth2.
I think the configuration is right, but I can't ping the @ IP
The physical link is up, but the redundant interface is not enabled.
How can I do, to have the reth2 physical link enabled ?
Thanks for your help.
Roland D
address 10.1.4.2/29;
}
}
}
=
Thanks to everybody
Best regards
Roland DROUAL
Le 31/05/2012 18:37, Tim Eberhard a écrit :
I can tell you with certainty that if you try to configure bridge
(which required a reboot). If any other families other than bridge are
configured it w
reth0.200;
reth1.200;
}
}
==========
Thanks for your help !
Roland DROUAL
Try adding:
set interfaces reth0 encapsulation flexible-ethernet-services
Le 30/05/2012 21:04, Chris Kawchuk a écrit :
reth0 {
encapsulation flexible-ethernet-services;
}
.. I belie
configuration check-out failed
Can you help me to have a link trunk with vlan 200 and vlan 954?
Thanks for your help.
Roland DROUAL
___
juniper-nsp mailing list juniper-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp
onfigured, I can see all the 48 interfaces ( ge-0/ and
ge-1/ ) with the command # show interfaces
And I can see only interfaces with a transceiver, with the command : #
run show interfaces terse
Thanks a lot (specially at Dale Shaw)
See you for the next problem.
:-)
Le 07/07/2011 12:43
I'm a beginner with Junos.
I'm trying to do a Virtual Chassis with two EX4200-24F.
All seem right.
In cli mode, I can see the interfaces from the master, but I can't see
the interfaces from the backup switch, starting from ge-1/0/0 until
ge-1/0/24 .
Is somebody can help me ?
Thank you
This is
14 matches
Mail list logo
