On Wed, 2007-05-16 at 11:49 -0700, yhlu wrote:
> PCI slot one has all
> > four interrupts working.
> >
> > What doesn't work yet is:
> > 1) PCI slots 2-4
> > -there doesn't seem to be any interrupts generated. slot 2 and 4 can do
> > ifconfig up, but don't transmit or receive any packets. slot 3
On 5/16/07, Jeremy Jackson <[EMAIL PROTECTED]> wrote:
> ports 1 and 2 don't detect drives.
>
known problem
YH
--
linuxbios mailing list
linuxbios@linuxbios.org
http://www.linuxbios.org/mailman/listinfo/linuxbios
On 5/16/07, Jeremy Jackson <[EMAIL PROTECTED]> wrote:
> Thanks for the reply, see below:
>
> On Wed, 2007-05-16 at 09:20 -0700, yhlu wrote:
> > 1. use smp 64bit kernel.
>
> I have Ubuntu feisty kernel, 2.6.20-14-generic #2 SMP, which shows 2
> CPUs with an AMD Athlon64 X2 4600+. Do I need any othe
On furthur testing, and correcting interrupt assignment in mptables.c, I
find that SATA port 3 is working completely (NCQ, hotplug).
port 4 detects a drive, but kernel hangs at boot
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.00: ATA-7: ST3250823AS, 3.03, max UDMA/133
Thanks for the reply, see below:
On Wed, 2007-05-16 at 09:20 -0700, yhlu wrote:
> 1. use smp 64bit kernel.
I have Ubuntu feisty kernel, 2.6.20-14-generic #2 SMP, which shows 2
CPUs with an AMD Athlon64 X2 4600+. Do I need any other kernel config
options?
> 2. s2865 onboard NIC is in silicon, so
1. use smp 64bit kernel.
2. s2865 onboard NIC is in silicon, so please refer irq routing in
s2895 or s2891 etc.
YH
--
linuxbios mailing list
linuxbios@linuxbios.org
http://www.linuxbios.org/mailman/listinfo/linuxbios
I have since discovered using a multimeter that the interrupt lines are
directly connected between all four PCI slots. I have adjusted
mptables.c to reflect the "swizzling" of the lines.
I can attach a simple logic probe to the PIRQ[A-D] and watch as each of
the four DEC tulips on a quad fast eth
I'm working on Tyan S2865 again here, Nvidia CK804, and I can't get
PCI32 bus interrupts going. I've got mptable.c working for onboard
devices and PCI-e sots.
I've got a quad-ethernet PCI card working in slot one, which
demonstrates that all 4 PCI INTR[1234] pins are working
however i can't seem
Well not unless you require RAM...
I just copied sunw/ultra40, adjusted superIO for serial output, and
whacked a bunch of stuff that looked like it was for 2nd CPU (it's a UP
board). Sure wish I knew what I was doing!
LinuxBIOS-2.0.0_ultra40_Fallback Wed Apr 11 21:26:06 EDT 2007
starting...
I'm working on the sun ultra40 which is very similar. Why would only one dimm socket work?
ron
--
linuxbios mailing list
linuxbios@linuxbios.org
http://www.openbios.org/mailman/listinfo/linuxbios
I did something porting about it one year ago at tyan.
status
all works except only can use one DIMM.
but according to my experience about AM2 socket. I guess after some
fine tuning it could work with 4 dimms.
YH
On 8/7/06, Richard Smith <[EMAIL PROTECTED]> wrote:
> I've got someone asking ab
I've got someone asking about the Tyan s2865 which is an nVidia based
board. Whats the status on these parts? The board is not listed in
the Tyan dir.
:00:00.0 Memory controller: nVidia Corporation CK804 Memory
Controller (rev a3)
Subsystem: Tyan Computer: Unknown device 2865
F
12 matches
Mail list logo
