Hi All,
I have the above PL board in a Mitrek Low-VHF model radio I am
modifying.
I want to be able to use the onboard PL, and feed an output to my
controller.
I do not have any information on how to reprogram the PL to anything
different, and also where to tap a switching voltage to the
ere..
> http://65.173.252.47/Miktrek_Info.htm
>
> 73
> Mike
> K5JMP
> www.k5jmp.us
>
>
> -Original Message-
> From: Repeater-Builder@yahoogroups.com
> [mailto:[EMAIL PROTECTED] Behalf Of Kevin & Natalia
> Mitchell
> Sent: Saturday, April 29, 2006 1:38 AM
>
HELP,
I have just tried to open my newly aquired 6mtr mitrek, with the key that I
had for my 10mtr mitreks. This key opens all 6 radios I have, brought at
different times, from different sources across the State.
I found that it would not open. The cut is the same and fits in okay
Are there diff
Hi All,
I have a Mitrek for 50Mhz, I want to convert it for use as a 6mtr repeater.
Question is, is it possible to make it as a repeater from a single unit, or
do I need two radios?
I have all the information on converting, as I built units for a 10mtr
repeater, and a 2mtr unit.
If I can not use
Good idea, did not think about this option. This will serve our situation
well.
And will be an easy fix.
Regards
Kev.
>
> As has been pointed out, there are some problems with
> running two different PL tones at the same time, both
> on the TX and at the RX sites. It can be done, but it
> also c
Hi All,
I am wanting to use one TX from our repeater site, to link to two link
RX's, these are on opposite sides of the repeater.
I was thinking about having two different CTCSS tones, one for each, and
then having the TX generate the two tones together. This way I can use one
freq., but
r - OT
> Kevin & Natalia Mitchell wrote:
>> Hi Guys,
>>
>> Sorry for the bandwidth, but I have a small problem when sending
>> messages to the group. It does happen on the other groups I belong
>> to. I used to be able to see any message I sent to the group, howeve
Hi Guys,
Sorry for the bandwidth, but I have a small problem when sending messages
to the group. It does happen on the other groups I belong to.
I used to be able to see any message I sent to the group, however other the
past 6 months when I send a message, I do not get a forward message f
Hi All,
I have a Doug Hall 4RV/2 voter.
I am in the process of connecting the unit up, but I can not find my manual
to wire and set it up.
I have connected up 3x receivers to the inputs, and toggled the switches to
operate, but the voter does not trigger any of the lines. So I need to check
the
Hi All,
Could someone please advise me on the lowest power setting a Mitrek 60watts
model can be?
I want to run one at around 10watts, but I have heard that some radios do
not like going down this. They become unstable.
I have 2m and 70cm units, 1 of each.
thanks in advance
Kevin.
Yahoo!
Do you know of any Computer based Spectrum analyser programs that would do
this job???
And Happy New Year to All, we are already 9 hrs gone.
Regards
Kevin, ZL1UDD
- Original Message -
From: "nj902" <[EMAIL PROTECTED]>
To:
Sent: Thursday, January 01, 2004 6:37 AM
Subject: [Repeater-Bui
This looks like it could be the result of a virus, I have received the same
message from 5 different sources so far.
Be careful, if it is genuine, sorry for the concern, but the same message,
sounds foul.
Kev.
- Original Message -
From: "Don" <[EMAIL PROTECTED]>
To:
Sent: Thursday, Decem
Hi All,
Does anyone have a couple of UHF (suitable for 430Mhz) duplexers surplus to
requirements, and are willing to sell??
These are for a full duplex link at 9Mhz spacing on RX/TX
Please bare in mind the cost for postage as I will require them to be mailed
to New Zealand.
Also I am looking for
Hi All,
I have just built a new set of 6x filters into a duplexer on 2m.
The problem I now have is what length do I make the interconnecting cables
between each filter, and then the output cables to feed 1x antenna.
I have read some information on this subject, however they do not appear to
agree
14 matches
Mail list logo