Brian
The correct frequency shaft will do more for distance and consistency then
any club head on the market. You may find some small changes with club head
but nothing to compare with the changes you can get with the correct
frequency shaft.
llhack
> [Original Message]
> From: Brian Parkinson
John
I have a set, 3-PW for $425 at our shop in Columbus, Ohio, we took in on
trade.
Lloyd Hackman
> [Original Message]
> From: <[EMAIL PROTECTED]>
> To:
> Date: 3/12/2007 3:06:07 PM
> Subject: ShopTalk: Fusion Irons
>
> anyone happen to have a set of Fusion
Alan
So, during the loading of the shaft and the first 1/4 cycle of the release
it is acting as a rigid body because once the shaft is loaded there are no
forces to change the position of the grip in the hands (not even a spring
force because flesh is not a spring) until the shaft passes through
s
*** Response below
> [Original Message]
> From: Alan Brooks <[EMAIL PROTECTED]>
> To:
> Date: 10/27/2006 10:13:53 PM
> Subject: Re: ShopTalk: Shaft behaviour
>
> Sorry, Lloyd, this mechanical engineer doesn't buy it. The hands are far
> to soft to produce a cantilevered response. Think of the
Alan
Even I will agree that the model is wrong when you think only of vibrating
the shaft in a frequency meter because you immediately think of multi pule
cycles. However our model only con ciders the first Quarter cycle of club
release. After impact how it reacts is no consequence. If the model w
Title: Any 1 iron components left?
Dan
How many do you wont? I have several of serseral differnet makes.
llhack e-mail [EMAIL PROTECTED]
- Original Message -
From: Dan Mueller
To: ShopTalk@mail.msen.com
Sent: 9/20/2006 12:05:42 AM
Subject: ShopTalk: Any 1 iron c
Title: Message
I suspect that they are trying to make lighter shafts which most likely corresponds to a softer shaft. As the shaft gets softer the basic lie should be more upright to compensate for the greater toe done deflection of the softer shaft during the swing. This follows the fact that I
Powerbuilt was built by H & B in Louisville, Ky.
llhack
- Original Message -
From: Bob S
To: ShopTalk@mail.msen.com
Sent: 3/15/2006 12:13:00 PM
Subject: ShopTalk: PowerBuilt
Have a reshaft job to do on a Powerbuilt 2 iron... The lable on the shaft showes it is a C flex. Is th
I will be there
- Original Message -
From:
To: ShopTalk@mail.msen.com
Sent: 2/26/2006 8:53:29 PM
Subject: Re: ShopTalk: Shaft Flex cpm
Well well Mr. Hackman we finally agree on something. You gonna be at the PCS show next weekend? Anybody else? Inkind, ~~myKey~~
Janet
When you find some one who plays without a grip then you can use the "true
frequency". I build the club to the frequency using the grip the player
will play with.
llhack
> [Original Message]
> From: Janet Perry <[EMAIL PROTECTED]>
> To:
> Date: 2/24/2006 11:36:34 PM
> Subject: ShopTalk:
b head speed to generate the centrifugal force to flex the shaft
llhack.
Lloyd Hackman
[EMAIL PROTECTED]
EarthLink Revolves Around You.
Burgess
I don't know where you think the lie might be and obviously I am not easily
convinced or I would be with the crowd on this subject. Being right handed,
I do ware out my glove on the heal of the left hand and have calluses on
the fore finger of my right hand, if that can be used as evidenc
Ed said:
I can easily see how Flex can affect accuracy, but no way should it be able to increase swingspeed.
Ed
That means that you can throw a fishing lure just as far with a very stiff fishing rod as you can with a soft tipped fishing rod. The tip speed has something to do with the prope
Alan said:
> Lloyd, you've got to be kidding. Do you really believe that at any time
in
> the swing the hands are restraining the club the same as being clamped in
a
> vise? I don't know what your 'Professor' said, or what question he was
> responding to, but I assure you the two boundary c
o correct, IMHO -- just a lot harder to
read.
>
> DaveT
>
> At 09:20 PM 1/16/2006, Dave Tutelman wrote:
> >At 07:50 PM 1/16/2006, Lloyd Hackman wrote:
> >>So your saying a spring does not reach it peak speed when it passes
though
> >>its neutral position or when
Alan said:
"Lloyd, if the butt of the shaft were rigidly clamped than what you say
would be true - maximum velocity would occur when the shaft was
straight. But the shaft of a swung golf club is not rigidly clamped, it is
being held in the hands which are both moveable and soft. That being the
man <[EMAIL PROTECTED]>
> To: ;
> Date: 1/16/2006 9:30:46 PM
> Subject: Re: ShopTalk: Shaft Quality and Bend Profiles
>
> At 07:50 PM 1/16/2006, Lloyd Hackman wrote:
> >So your saying a spring does not reach it peak speed when it passes
though
> >its neutral position or w
lk: Shaft Quality and Bend Profiles
>
> At 06:18 PM 1/16/2006, Lloyd Hackman wrote:
> >My real concern is what does shaft profiling have to do with getting the
> >shaft back to straight and square. All shafts have their peak performance
> >when they are back to straight and t
he actual shaft you are going to use.
>
> /Ed
>
> Lloyd Hackman wrote:
> > Ed
> >
> > What good is all of that data if you fit the shaft to get back to
straight
> > and square at impact? I can see if you don't expect the shaft to be
> > straight and square a
Ed
What good is all of that data if you fit the shaft to get back to straight
and square at impact? I can see if you don't expect the shaft to be
straight and square at impact, that data may mean something but I don't
know what. If we are tuning each club we build to a given frequency what
makes
but now
> accepted in the golf industry). If you stay within the same shaft company
> maybe but not if you use 15 different shafts from 15 different shaft
> manufacturers. The 15 different shafts could have the same starting butt
> frequency but all will perform differently.
> André.
&
Lloyd. If I understand correctly you are basically saying that shaft
> profiling is useless and that butt frequency is the only answer. Do you
have
> any data regarding your statement below i.e robotic testing and so forth.
> André.
>
> - Original Message -
> From: &qu
e of about 15 CPM. We find that if you are not within + or - 4 CPM you can not expect the same performance from the club. that is why many times when you replace a shaft supposedly with the same shaft the club will not perform the same.
Lloyd Hackman
- Original Message -
From: Tom
straight and
square with the proper shaft for the player.
> Andre
>
>
>
> >
> > - Original Message -
> > From: "Lloyd Hackman" <[EMAIL PROTECTED]>
> > To:
> > Sent: Sunday, October 30, 2005 10:05 AM
> > Subject: Re: ShopTal
e built many drivers over the years and believe
me
> the head plays just as an important part in ball flight than the shaft.
> A
>
>
> - Original Message -
> From: "Lloyd Hackman" <[EMAIL PROTECTED]>
> To:
> Sent: Sunday, October 30, 2005 8:54 AM
Was it the head or was it the shaft frequency that was a better fit for
your swing? Find out what frequency that club was and build another club
to the same frequency and see what happens. My guess is it was not the head.
llhack
> [Original Message]
> From: Tom and Donna <[EMAIL PROTECTED]>
> T
Arnie
Unless you are saying that the statement "Understand that a graphite shaft spreads bending force over a larger range of the shaft length" refers only to the stress concentration area you still have not addressed the question. If this is what you are trying to say in this statement, sprea
Arnie
Are you saying that what you wrote "Understand that a graphite shaft spreads bending force over a larger range of the shaft length" is not right. Or what did you want us to understand.
llhack
- Original Message -
From:
To: ShopTalk@mail.msen.com
Sent: 10/15/2005 4:19:5
Arnie
Why do you think the bending force distribution is any different in graphite then in steel?
llhack
- Original Message -
From:
To: ShopTalk@mail.msen.com
Sent: 10/15/2005 2:37:48 AM
Subject: Re: ShopTalk: swingweight
Understand that a graphite shaft spreads bending force
s, of
your
> device was that it was just that "A PIECE OF CRAP"
>
> RK
>
>
> - Original Message -
> From: "Lloyd Hackman" <[EMAIL PROTECTED]>
> To:
> Sent: Thursday, October 13, 2005 9:23 AM
> Subject: Re: ShopTalk: Wishon Short Driv
ta years and as you no doubt are aware, I would never build a
set
> of clubs for a guy based upon a computer readout. He has to hit the clubs
> first before I ever let him pay a dime.
>
> TFlan
>
> - Original Message -
> From: "Lloyd Hackman" <[EMAIL PRO
gt; if you start looking at other factors, like % of shots on-center, the
> average distance may well be better at the shorter length.
>
> Tedd
>
> -Original Message-
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] Behalf Of Lloyd Hackman
> Sent: Wednesday, Octobe
Dave
How much did you change the frequency of the shaft?
llhack
> [Original Message]
> From: Dave Tutelman <[EMAIL PROTECTED]>
> To:
> Date: 10/12/2005 6:12:24 PM
> Subject: RE: ShopTalk: Wishon Short Driver Article
>
> At 04:08 PM 10/12/2005, Childers, Tedd A wrote:
> >Personally, I would
>
12/2005 5:46:57 PM
> Subject: RE: ShopTalk: Wishon Short Driver Article
>
> At 05:21 PM 10/12/2005, Lloyd Hackman wrote:
> >Yes, but you would give up that distance. The club head velocity is a
> >function of Radius squared...
>
> The clubhead velocity is a proportional to the
0+ grams), and
that
> is what I have a problem finding, at least in a model that has the specs I
> want (450+ cc, ~12* loft).
>
> Tedd
>
> -Original Message-
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] Behalf Of Lloyd Hackman
> Sent: Wednesday, October 1
"Between the ears"Lloyd Hackman wrote:
Tom
Why should I do it with length when selecting the proper frequency shaft
provides the best accuracy and distance and the player has already decided
to play with the longer club. The primary reason people have had trouble
with longer shafts in t
Tflam
Who was the club builder that built that set of clubs you refer to? The
fitChip dose not build the clubs or recommend frequencies in set that don't
fall on straight slope or a smooth curve.
llhack
> [Original Message]
> From: tflan <[EMAIL PROTECTED]>
> To:
> Date: 10/12/2005 4:04:20 PM
h a length definitely shorter than
> 45" for your golfers.
>
> TOM
>
> -Original Message-
> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
> On Behalf Of Lloyd Hackman
> Sent: Wednesday, October 12, 2005 10:44 AM
> To: ShopTalk@mail.msen.com
> Subject: RE
I am sorry but the Wishon article starts right off with the wrong premise.
He throws in the premise that the shorter the club the better the accuracy.
He ignores the fact that the real parameter for accuracy is shaft
frequency. If you can match the proper shaft frequency to the players swing
and ge
Arnie
I recently saw an old post that you place on another Forum where they were discussing the FitChip and you made the statement that you understood that it always recommended shaft stiffness that were to high. So that you will have more accurate information next time I can tell you that abo
What you really need to know is what frequency an individual needs to match
his swing timing. If it is an R, S or X is irrelevant.
llhack
> [Original Message]
> From: skismith <[EMAIL PROTECTED]>
> To:
> Date: 7/26/2005 1:16:30 AM
> Subject: Re: ShopTalk: Club Connectors
>
> Can anyone help me
Now that there seems to be some agreement that slope is important and veries from player to player, how is everyone determining a players slope?
llhack
- Original Message -
From:
To: ShopTalk@mail.msen.com
Sent: 5/16/2005 9:42:57 AM
Subject: Re: ShopTalk: Clarification needed
J
Duncan
I have a Toski offset 10* loft "No Limits" head, new. Black with a copper
face.
llhack
> [Original Message]
> From: Duncan McKenzie <[EMAIL PROTECTED]>
> To:
> Date: 5/12/2005 7:09:11 AM
> Subject: ShopTalk: Lo Profile
>
> Hi,
>
> Does anyone know of a supplier of low profile , offset r
man <[EMAIL PROTECTED]>
> To:
> Date: 5/10/2005 5:22:11 PM
> Subject: Re: ShopTalk: Clarification needed
>
> At 04:32 PM 5/10/2005, Lloyd Hackman wrote:
> >Dave, your attitude tward the slope in a set of club is rather disturbing
> >to me. Very few players play on a Brunswic
Dave, your attitude tward the slope in a set of club is rather disturbing
to me. Very few players play on a Brunswick slope anyway. From a data base
of about three hundred players of all handicap ranges, I found that an
average slope was more like 2.3 CPM per club. With about 10 to 15% of the
playe
When will people understand that clubhead speed or launch monitors can not
fit the proper shaft to your swing. It is timing, timing and timing
llhack
> [Original Message]
> From: Alan Joyce <[EMAIL PROTECTED]>
> To:
> Date: 4/17/2005 9:06:34 AM
> Subject: ShopTalk: rifle lite
>
> Has anyone
How about this on Scandium.
Discovered : by L.F. Nilson in 1879
Isolated in Uppsala, Sweden
Origin : The name is derived from 'Scandia', the Latin name for Scandinavia.
Description :
A silvery metal that tarnishes in air, burns easily and reacts with water.
It is used only for research purpose
Sure will, wouldn't miss it.
llhack
- Original Message -
From:
To: ShopTalk@mail.msen.com
Sent: 2/13/2005 4:54:25 PM
Subject: Re: ShopTalk: Wishon article
That's what we were laughing about using the recommendation that you gave us with the club and shaft you suggested. No que
Yes those of you that think Ping and the launch monitor is custom fitting
might as well give it up. The launch monitor is only of any value, after
you have the proper shaft selected, to select the loft of head the player
needs. The primary problem the OEMs have is that only 40% of the players
out t
If you never tried the our recommendation, and only joked about it, you will never know whether it was right or not, will you? You wouldn't be the first to be surprised that our recommendation was different then what they thought but fond it to be the answer to more distance and accuracy.
llhac
How do you factor in a "swinging" release, versus a "hitting" release?
Bob Freer
Bob
When you work with the time from release to ball impact it dose not really matter, whether the player is a hitter or swinger, if the speed and the release to impact time is the same, they need the sam
I had a chance to read Tom Wishon's article on his new 715CLC driver that John
directed us to. However it was the article following that one that drew my
attention "shaft Fitting". In this article Tom directs us to page 52 and 53 of
his book. Having read his page 52 and 53 as he suggests to all
Jerry
The primary problem is that as they are currently winding them they can not get
fiber aligned directly up and down the shaft. This reduces the effeciency of
the use of the high performance fiber.
llhack
-Original Message-
From: Ed Reeder <[EMAIL PROTECTED]>
Sent: Jan 28, 2005 3:1
To John and Alan and those interested
Yes the shaft when vibrated will find the plane of least resistance or as John
would say the weakest plane. This should be a satisfactory plane to align the
shaft in. However, I feel that the most important factor in shaft alignment is
the shafts stability
He could be a flat liner. Have you tried that?
llhack
- Original Message -
From: tflan
To: Shoptalk
Sent: 11/1/04 7:36:21 PM
Subject: ShopTalk: Old fart
For the first time in years, I'm just about stumped. I have an old guy (68) who's hitting his irons about as well as can be
ble to make a 5 iron to frequencies as low as 220 CPM.
llhack
- Original Message -
From: Lloyd Hackman
To: [EMAIL PROTECTED]
Sent: 10/25/04 10:01:20 AM
Subject: Re: ShopTalk: senior ladies shafts
I have "FitChip Prescription" shafts with standard tip and but
My shafts are Forest Green with Gold printing.
llhack
- Original Message -
From: RSkirvin
To: [EMAIL PROTECTED]
Sent: 10/25/04 6:16:36 PM
Subject: RE: ShopTalk: senior ladies shafts
Thanks to David and All who replied! Lloyd, she also wants a certain color and she prefers so
----
From: Lloyd Hackman
To: [EMAIL PROTECTED]
Sent: 10/25/04 10:01:20 AM
Subject: Re: ShopTalk: senior ladies shafts
I have "FitChip Prescription" shafts with standard tip and butt diamensions that can be made up in frequencies as low as 170 CPM.
llhack
- Original Message
If your are interested in Iron shafts this same make shaft is available to make a 5 iron to frequencies as low as 220 CPM.
llhack
- Original Message -
From: Lloyd Hackman
To: [EMAIL PROTECTED]
Sent: 10/25/04 10:01:20 AM
Subject: Re: ShopTalk: senior ladies shafts
I have
I have "FitChip Prescription" shafts with standard tip and butt diamensions that can be made up in frequencies as low as 170 CPM.
llhack
- Original Message -
From:
To: [EMAIL PROTECTED]
Sent: 10/23/2004 12:44:10 PM
Subject: Re: ShopTalk: senior ladies shafts
In a message dated
Dave
Yes I think David was talking about the speed curve not the acceleration
curve. I do tend to agree with Davids thought however because the transfere
of energy occurs over time , even thought it is a very short time. The
velocity changes during this time period because of impact. If the club
h
PatK
At the point of impact, acceleration has nothing to do with ball speed. The momentum transfer equation is 1/2 M V^2. Acceleration creates velocity but only the velocity at the time of impact maters. Since mass enters into this equation the 5g will add 5 yards to the distance (at 100% effic
David
The ball matches the club head of No. 1 the best. If you can get the natural frequency of the ball to be the same as the natural frequency of the face you will get the best smash No.. It is the trampoline affect, if you bounce with stiff legs you go three feet high while if you bend your
Frank and David
Even though the C.O.R. of each of these heads are the same, because the have different face diamensions the natural frequencies of the faces will be different. C.O.R. is based only on one standard test ball or impacting body. The properly selected ball that matches the face's na
Subject: RE: ShopTalk: double weenie shaft
That's correct, the laws of physics do not apply to slow swingers, only fast ones.
- Original Message -
From: Lloyd Hackman
To: [EMAIL PROTECTED]
Sent: 6/14/2004 7:28:48 PM
Subject: RE: ShopTalk: double weenie shaft
Getting the ball i
Getting the ball in the air has nothing to do with shaft stiffness except for the timing of getting the shaft back to straight especially for the slow club head speed player. I have successfully put to may low club head speed players, that could not get senior shafted clubs off the ground into st
Chris
I have FitChip Prescription shafts that will frequency in Irons to as low as 200 CPM amd woods to as low as 170 CPM. these shafts are made for me, to my specifications, by Rapport.
llhack
- Original Message -
From: Chris Burns
To: ShopTalk
Sent: 6/11/2004 11:13:12 PM
Su
David did you use a split grip in both cases or did you use the split grip before you butt cut the shaft and the full grip after assembly?
llhack
- Original Message -
From:
To: [EMAIL PROTECTED]
Sent: 3/18/04 6:36:48 AM
Subject: ShopTalk: swingweight question
Hi Jent's,I came acr
That is exactly why Callaway got into making golf balls in the first place,
matching their balls to their heads.
llhack
> [Original Message]
> From: Burgess Howell <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Date: 2/5/04 3:32:14 AM
> Subject: Re: ShopTalk: (Not Clubmaking) Golf Ball Question
d was more important.
Funny thing is that today most every mfr is producing low compression high density covered balls. The Titelist Pro V1x is a low compression ball but its still the most popular on tour, regardless of temperature.
TFlan
- Original Message -
From: Lloyd Hackman
To
Using a 100 compression ball is like jumping on a trampoline with your legs stiff. The one that flexes his knees and times the release properly will go much higher on the trampoline. The new club faces are trampolines, so a ball with the same release timing as the face ( softer compression) goes
If you are going to play a spring faced driver why would you want a 100 compression ball?
llhack
- Original Message -
From: Steve \"Cub\" Culbreth
To: [EMAIL PROTECTED]
Sent: 2/4/04 2:48:49 PM
Subject: Re: ShopTalk: (Not Clubmaking) Golf Ball Question
Alan,
Thanks for the in
Richard
Please go to www.matweb.com and get your facts on any material.
Looking up 1010 and 1080 carbon steel and the 4140 (a different grade of steel since it contains Chrome) are still all listed with a Youngs Modulus of Elasticity of 2970 PSI.
- Original Message -
From
The modulus of elasticity for the low carbon steel and higher carbon steel is
basically the same. It is the yield stress that is significantly different and would
have no affect on frequency differences. The only thing left is out of round and a
material thickness difference at the weld that wo
Doug
Don't follow manufactures tipping instructions. Less tipping lowers the
slope and butt cutting only will be close to a flat line for any shaft.
llhack
> [Original Message]
> From: Doug Clark <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Date: 10/8/03 3:01:55 PM
> Subject: ShopTalk: Frequ
tflan
To answer your question, if the shaft is straight the hard side or the side
with more thickness or more material will end up on top of the curvature
when bent and free to rotate to the stable position. If the shaft is only
bowed only the shaft will rotate into the stable position of bow down
If the head was truly forward of the shaft prior to impact, it would
indicate that the shaft had dropped below its peak speed or be decelerating
with respect to the hands. The primary cause of it showing up as being
ahead of the shaft is the affect of Centrifugal force pulling down on the
head C. G
Michael
The two shafts with the same frequency will have exactly the same timing between full deflection (irregardless of amount of deflection) and getting back to straight. The flex pattern or flex point might cause a difference in feel but if the shaft dose not get back to straight it will n
Michael
Are we talking finished club frequency or some raw shaft frequency given by the producer?
llhack
- Original Message -
From: Michael Pogor
To: [EMAIL PROTECTED]
Sent: 10/1/03 12:06:13 PM
Subject: RE: ShopTalk: Constant frequency
My apologies David,
I forgot to sta
Michael
Frequency is frequency independent of the shaft. If a certain frequency matches the timing of your swing why would the shaft frequency change unless you changed your timing. You can change your timing buy changing the length of your swing and a few other things but it is not the easiest
Just arrived back in Florida. In most cases I have found that in the case of flat liners all clubs are on the same frequency. There are no fixed rules, I have found a few players where the woods are on a separate line both sloped and flat but with no standard rule. I am not sure you can group all
Flat line you clubs at the frequency of your favorite club.
llhack
> [Original Message]
> From: Doug Clark <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Date: 9/29/03 7:39:28 PM
> Subject: Re: ShopTalk: Constant frequency
>
> I am combining Lloyd's and Michael's posts here. I hope it's not to
Doug
I find 10 to 15% of the players I fit are flat liners. There was a time when I thought every one should be. Being a flat liner has nothing to do with tempo. The main reason that people are flat liners is that they take every club back the same distance rather then taking each club back dif
He probably has the wrong frequency shaft. I recently had a long drive guy
who was breaking shafts until I fitted him into a softer shaft that matched
his timing and he did not break any more shafts.
llhack
> [Original Message]
> From: <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Date: 7/24/0
Timing is everything . That means clubhead speed means nothing to selecting shaft stiffness.
llhack
- Original Message -
From:
To: [EMAIL PROTECTED]
Sent: 5/29/2003 1:46:25 PM
Subject: Re: ShopTalk: Question
Rich:
I am assuming that your swing speed indicates a stiff flex?
My
It depends on which one is the closest to fitting your swing timing.
llhack
- Original Message -
From:
To: [EMAIL PROTECTED]
Sent: 5/28/2003 6:58:51 PM
Subject: ShopTalk: Question
What could you expect the distance loss would be between a "stiff" flex shaft installation and a "
Don
Based on your comment I took another look at your FitChip
data. With the older software your 46" driver came out at 252 CPM. With the
latest software (Used for the last two years, your data was taken maybe four
years ago.) I get your driver at 241, 5 wood at 272, 5 Iron at 314 and 9 Iro
Mike
One last comment on my position on this subject. Since the
torque deflection is negligible during the down swing you must conclude that
torque has nothing to do with the recovery of the head back to square. I
have also gleaned from this discussion that some think that a softer torque
It is amazing how some one like RK
who depends on science every day to stay alive can reject the use of science in
club making. I guess he feels his doctors should go back to the age of leaches
and blood letting as a cure.
llhack
- Original Message -
From:
Richard Kennedy
Mike
The Torque of the shaft must be designed to resist
the toe impact with the golf ball. Despite what most on this forum think or
imply the player can not apply enough torque to the shaft during the swing to
significantly deflect the shaft in torque Therefore the primary purpose for
shaf
lowest torque is always better.
llhack
- Original Message -
From:
[EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Monday, March 17, 2003 11:03
AM
Subject: ShopTalk: How to pick
torque?
When choosing shafts for a customer is their a rule of thumb
to look at
weights
> >
> >
> >> But Lloyd, look at what you get (this from the website);
> >>
> >> "With each Pro-Balance fitting system you get three adjustable weight
> >> inserts, a velour travel pouch to carry the weights and an
installation
> >
amn!
>
> ;-)
>
> TFlan
>
>
>
> - Original Message -
> From: "Lloyd Hackman" <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Sent: Thursday, March 13, 2003 8:45 AM
> Subject: Re: ShopTalk: Counter balance weights
>
>
> > $40.00 per club for their weights.
> >
> > llhack
>
$40.00 per club for their weights.
llhack
- Original Message -
From: <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Thursday, March 13, 2003 3:47 AM
Subject: Re: ShopTalk: Counter balance weights
> the high weight tuning kit is 70-100 grams, putter weights were 10,
> 30 or 50 grams
You should not do lie testing until you can use the shaft the
player is going to play with.
llhack
- Original Message -
From:
Al Taylor
To: [EMAIL PROTECTED]
Sent: Sunday, March 09, 2003 7:39
PM
Subject: Re: ShopTalk: best dynamic
fitting
Alan,With the usual
Since club head speed is not a good indicator of needed shaft
flex what good are either system any way?
llhack
- Original Message -
From:
Alan Joyce
To: [EMAIL PROTECTED]
Sent: Tuesday, March 04, 2003 12:57
PM
Subject: ShopTalk: RSSR vs DSFI
I downloaded the D
The diameter of the shaft was reduced by approximately
7% which would reduce the frequency since the moment of inertia is dependent on
the square of the materials distance from the center of the shaft. The paint is
probably an epoxy. However reducing the mass alone would increase the
freque
en't tried a simulator that
> predicted my swing correctly yet.
>
> Bernie
> Writeto: [EMAIL PROTECTED]
>
>
> - Original Message -
> From: "Lloyd Hackman" <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Sent: Monday, January 27, 2003 5:
Graham
I just returned from the PGA Show where I saw a demo fitting at the Harrison
Shaft booth where they were using the Full Swing Simulator. They were using
trial and error, watching trajectory and distance to optimize the shaft. He
specifically demonstrated that the shaft that was too soft for
Check Out this picture. Probably not your best player but it can happen with
a late loading of the shaft.
llhack
- Original Message -
From: "Alan Brooks" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Tuesday, January 21, 2003 3:36 PM
Subject: Re: ShopTalk: 20 min talk
> Thanks D
1 - 100 of 127 matches
Mail list logo
