On 1/2/19 12:37 AM, Lukasz Majewski wrote:
> This patch is necessary to initialize some board/soc specific clocks -
> like anatop, which is used to clock PHY and FEC block itself.
> 
> The initialization is performed with device tree by introducing two new
> properties - namely;
> 'fsl,enet-loopback-clk' and 'fsl,enet-freq' which specify the need to
> select proper enet clock and the clock value itself.
> 
> Previously this setup was done in the board_etc_init() function, which
> has been removed after switching to DM/DTS.
> 
> Signed-off-by: Lukasz Majewski <lu...@denx.de>
> ---
> 
>  drivers/net/fec_mxc.c | 25 +++++++++++++++++++++++++
>  drivers/net/fec_mxc.h |  2 ++
>  2 files changed, 27 insertions(+)
> 
> diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
> index 99c5c649a0..728d6c9456 100644
> --- a/drivers/net/fec_mxc.c
> +++ b/drivers/net/fec_mxc.c
> @@ -1297,6 +1297,23 @@ static void fec_gpio_reset(struct fec_priv *priv)
>       }
>  }
>  #endif
> +/*
> + * This function is mostly intended for some soc/board specific
> + * clock initialization (like anatop clock on iMX6) done
> + * previously in board_eth_init()
> + */
> +__weak int set_fec_clock(int fec_id, enum enet_freq freq);
> +
> +static int fec_clk_init(struct udevice *dev)
> +{
> +     struct fec_priv *priv = dev_get_priv(dev);
> +     int ret = 0;
> +
> +     if (priv->enet_loopback_clk)
> +             ret = set_fec_clock(dev->seq, priv->freq);
> +
> +     return ret;
> +}
>  
>  static int fecmxc_probe(struct udevice *dev)
>  {
> @@ -1321,6 +1338,10 @@ static int fecmxc_probe(struct udevice *dev)
>               priv->clk_rate = clk_get_rate(&priv->ipg_clk);
>       }
>  
> +     ret = fec_clk_init(dev);
> +     if (ret)
> +             return ret;
> +
>       ret = fec_alloc_descs(priv);
>       if (ret)
>               return ret;
> @@ -1455,6 +1476,10 @@ static int fecmxc_ofdata_to_platdata(struct udevice 
> *dev)
>       }
>  #endif
>  
> +     priv->enet_loopback_clk = dev_read_bool(dev, "fsl,enet-loopback-clk");
> +     if (priv->enet_loopback_clk)
> +             dev_read_u32(dev, "fsl,enet-freq", &priv->freq);

dev_read_u32() returns error value, so what happens if this fails ?

> +
>       return 0;
>  }
>  
> diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h
> index e9a661f0a1..666b34304c 100644
> --- a/drivers/net/fec_mxc.h
> +++ b/drivers/net/fec_mxc.h
> @@ -261,6 +261,8 @@ struct fec_priv {
>  #endif
>  #ifdef CONFIG_DM_ETH
>       u32 interface;
> +     bool enet_loopback_clk; /* anatop reference clk via PAD loopback */
> +     enum enet_freq freq;
>  #endif
>       struct clk ipg_clk;
>       u32 clk_rate;
> 


-- 
Best regards,
Marek Vasut
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot

Reply via email to