Bob,
My linux system, Kubuntu 22.04 has been handling my FT991a just fine, the usb
drivers were probably in the distribution. It sees the rig just fine over the
single usb cable and is using the on-board sound card.
I never needed to download them at all. I did have trouble with a previous
version, but not in a few years with this one.
73,Andy, ka2uqw
On Wednesday, December 6, 2023 at 02:24:58 PM EST, robert evans LAST_NAME
via wsjt-devel <[email protected]> wrote:
An update of my windows IC-705 testing ... The asus win11 i9 laptop
/ WSJT-X 2.7.0-rc2 / IC-705 still was NOT decoding. Everything, including
rig control, was working fine. (BTW this IC-705 firmware ver has a FT8
preset.) Installed fldigi 4.2.? that i use for nbems traffic nets for
thor22 msfk Olivia etc. That worked well even made a psk31 qso. When i
went back to WSJT-X 2.7.0-rc2 it started decoding just fine! And I made a
couple qso on FT8 just fine. And my posts are on PSK rep as well as
stations that hear me! I wonder if Icom and Yeasu will offer usb drivers
for linux soon. Back to linux for now. BCNU DE N2LO~>
On 12/05/2023 9:14 AM EST robert evans LAST_NAME via wsjt-devel
<[email protected]> wrote: All good suggestions. Thank
You. Last night.. Double checked everything on the old dell i3 win10
and it started decoding just fine. The thing is, that it is so slow, i
loose track of what i did and didn't do when i make changes. And it
takes forever to reboot. I keep it around because it is about the bare
minimum system to support the usb drivers now used by windows for modern
radios. ft-991, ft-dx10, ic-9700, ic-705, etc. etc. etc. So, as a beta
test of WSJT-X 2.7.0-rc2 on a old dell i3 win10 with the IC-705 it worked
fine. Back to the asus win11 i9 laptop / IC-705 : When WSJT-X
2.7.0-rc2 did decode the dt was like 0.2 or less. I'll revisit that soon.
Thanks Again. N2LO~>
On 12/05/2023 3:52 AM EST Kari Sillanmäki via wsjt-devel
<[email protected]> wrote: OM, Also make sure
that you are not in "Hound" mode with the "Rx All Freqs" unchecked. 73's
de Kari, oh2gqc On 12/4/23 20:57, robert evans LAST_NAME via wsjt-devel
wrote:
Using a IC-705 over the weekend and after
installing the usb drivers in a asus win11
i9 laptop i started WSJT-X 2.7.0-rc2. The rig control worked fine and the
signals
where being displayed in the spect graph,
but no decodes. Double checked the time set.
Still no decodes. Walked away for many minutes and there were
decodes when i got back, but only a few. Installed WSJT-X 2.6.1 and tried
again. Same behavior. Every once in a awhile it would decode a
frame and then none for long periods of
time even though the spectrum graph showed
signals on the waterfall continuously. Switched to an old dell i3 win10
laptop
and saw the same behavior with wsjt-x. Tried fldigi and it decoded Olivia and
psk31 as well as cw no problem. Tried JS8 as well - no problem.
Back to WSJT-X and double checked the
settings. Every once in a long while
it might decode what looks like a frame. N2LO~>
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
