Hi Brian Your audio settings are now right, does your PTT LED light when you try to transmit?
I found with mine I had to set the playback mixer Wave level fairly high and to make the PTT more reliable I put the link on JP4. Les G3VYZ --- In digitalradio@yahoogroups.com, "Brian" <[EMAIL PROTECTED]> wrote: > > Hello again, > > Yes, I did reset the settings. I have the audio in set for 3 and the > audio out set to 7. I have the PTT com port blank. I now get a > display and a waterfall, but am not able to key up the TS-2000. > > Any further suggestions? > > And, most grateful for your help!!! > > 73 de KC9HEK > Brian > > > > > --- In digitalradio@yahoogroups.com, "Andrew O'Brien" > <andrewobrie@> wrote: > > > > Did you try to change the requested input and output settings to > those that > > match the USB audio codec ? > > Change the settings in "options" in the main WSJT area. > > > > > > > > On 10/28/07, Brian <kc9hek@> wrote: > > > > > > Hello Andy, thank you for getting back to me. Ok, I think I'm > > > starting to get the idea. I can't cut and paste the text from the > > > DOS window, but could certainly post a screen shot of it. But in > > > summary here is what I've got: > > > > > > First I have an error reading wsjt.ini and continuuing with > defaults. > > > Next I have a message ID Interval 10 > > > This sequence is repeated a second time. > > > > > > Then I have a message "Using PortAudio" followed by a table. I am > > > not sure how this table will come accross in this message but > here is > > > a try: > > > > > > Audio Device Input Output Name > > > 0 2 0 Micorsoft Sound Mapper-Input > > > 1 2 0 Realtec HD Audio Rear Input > > > 2 1 0 Modem #2 Line Record > > > 3 2 0 USB Audio Codec > > > 4 0 2 Microsoft Sound Mapper Output > > > 5 0 2 Realtec HD Audio rear output > > > 6 0 1 Modem #2 Line Playback > > > 7 0 2 USB Audio CODEC > > > > > > Default Input:0 Output:4 > > > Requested Input:0 Output:0 > > > Opening devise 0 for input, 4 for output. > > > Audio streams running normally. > > > > > > I need to point out that the Realtec is the internal sound card > and > > > the USB Audio Codec is the SignaLink sound card. > > > > > > I hope this will be able to help you point me in the right > direction. > > > > > > Thank you, > > > > > > 73 de KC9HEK > > > Brian > > > > > > --- In digitalradio@yahoogroups.com <digitalradio% > 40yahoogroups.com>, > > > "Andrew O'Brien" > > > <andrewobrie@> wrote: > > > > > > > > In the WSJT dos-type window that boots up, what do your device > > > settings say > > > > ? > > > > > > > > > > > > > > > > On 10/28/07, Brian <kc9hek@> wrote: > > > > > > > > > > Good afternoon folks, > > > > > > > > > > I have recently downloaded the WSTJ software for use with > JT65. I > > > > > have also read the very well done Bozo's Guide. (Thank you.) > That > > > > > said, I am unable to get the software configured properly. > > > > > > > > > > I have been running the more common digital modes for almost > two > > > > > years. I rountinly uses MultiPSK and DM780 using my existing > > > > > configuration. Basically, I have HRD deluxe connected to my > TS- > > > 2000 > > > > > on Com Port 1. I have the SignaLink USB connected to the 13 > pin > > > Aux > > > > > on the TS-2000. In both DM780 and MultiPSK the sound card > > > inititates > > > > > the transmit signal. > > > > > > > > > > In both of these other softwares, I can also choose which > sound > > > card > > > > > to use and have identified the SignaLink as the appropriate > sound > > > > > card. > > > > > > > > > > When trying to get WSTJ to run, I have gone into my Audio > > > Properties > > > > > (Windows XP PRO) and have made the SignaLink my default sound > card > > > > > with no success. > > > > > > > > > > I suspect my setup isn't all that uncommon and that I am > missing > > > > > something very simple and obvious. If someone could help me > out, > > > it > > > > > would be most appreciated. > > > > > > > > > > Thank you in advance, > > > > > > > > > > 73 de KC9HEK > > > > > Brian > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > -- > > > > Andy K3UK > > > > www.obriensweb.com > > > > (QSL via N2RJ) > > > > > > > > > > > > > > > > > > > > > -- > > Andy K3UK > > www.obriensweb.com > > (QSL via N2RJ) > > >