I am also a big fan of the PortaPaddle and PortaPaddle II, using it with
all Elecraft portable rigs. It weighs nothing, is nearly indestructible,
and is well made.
73 Eric WD6DBM
On Fri, Sep 18, 2020, 11:39 AM Fred Jensen wrote:
> American Morse Equipment. Obviously depends on your
Working with Rob at Elecraft Service, I removed and checked the KIO3
Digital I/F board and found L1 blown. L2, L3, R12, and R13 are all
good. L1 is on the ground lead from the sub-D9 connector, pin 5 to
ground in the K3. Definitely blown as there is a carbon smudge next
to L1. I installed
There are so many variables here that it kind of defies analysis. First of all,
the KX3 uses a BNC connector. Almost always, as you have done, connecting to a
good load, that will handle some power, probably requires adapting to type N. A
reasonable load might be something like a NARDA 366NM
Hi Martin,
I got that from the video except I missed the ‘Microsoft surface tablet’ part.
Thanks,
Richard W5SXD
> On Sep 18, 2020, at 4:21 PM, Martin Sole wrote:
>
> I recall, Microsoft surface tablet running Linux on a virtual machine, was
> mentioned in a video some time back.
>
>
I recall, Microsoft surface tablet running Linux on a virtual machine, was
mentioned in a video some time back.
Martin
HS0ZED
Sent from my iPhone
> On 17 Sep 2020, at 23:46, Richard Allen wrote:
>
> Can someone please tell me what model pads are used in the Elecraft video
> from the
Hi,Here is a club link for a portable paddle.http://www.w8cso.org/teneke.php 73
Jim HK7SSS In a message dated 9/18/2020 11:41:51 AM Pacific Standard Time,
k6...@foothill.net writes:
On 9/17/2020 10:09 PM, Alan Bloom wrote:
> I am currently "sheltering in place" far from home and would like to
American Morse Equipment. Obviously depends on your definition of
"cheap," but I use their Porta-Paddle with my K2 in the field.
73,
Fred ["Skip"] K6DGW
Sparks NV DM09dn
Washoe County
On 9/17/2020 10:09 PM, Alan Bloom wrote:
I am currently "sheltering in place" far from home and would like
Hi Mike,
This seems to be a duplicate post (see
http://elecraft.365791.n2.nabble.com/KPA-1500-FlexRadio-6400-td7665007.html),
though I'm not sure if your questions were fully answered the first time.
First, to search the archives of this reflector, go to
There is a new manufacturer advertising in Sprat magazine. Model UMPP-1 is
advertised bench model and there are others $60 to US. Not quite "cheap" but
very small and good for travelling.
www.umpp-cw.com
gm0...@gmail.com
73 David G3UNA/G6CP
> On 18 September 2020 at 08:36 David Gilbert
Mike,
I’ve done some of these mods, but not all.
I replaced the MAR6 this morning and it now hears a little better, but the
S-meter on the K3 is not moving. Q3 is next.
AND I JUST REMEMBERED!!! When I was setting up the rover before the contest, I
was keying all the equipment with the
Thanks Don,
I had a MAR6 in stock and installed it after breakfast. There is now a
noticeable change in RX noise with the noise bridge turned on, but nowhere near
what is needed, so I’ll order a Q3.
73,
Mark K2QO
FN03ra
> On Sep 18, 2020, at 12:23 AM, Don Wilhelm wrote:
>
> Mark,
>
>
You could use your keyboard with N1MM. Won't cost you anything.
Barry W2UP
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
On 2020-09-17 23:09:-0600, Alan Bloom wrote:
>So who makes a decent, inexpensive key paddle? (By the way, I don't
>need the iambic feature, so a single-lever model would be fine.)
>
>Alan N1AL
I keep forgetting that this list is different from all the rest I sub to...the
replies don't go to
I have been very happy with a key from CW Morse (cwmorse.us) in Texas.
The shipping was lightening fast and there should be one that would fot
your needs. The link is below if it works.
https://cwmorse.us/
73,
Aaron
kk4kfg
__
There are several cheapies on eBay for about $35. You'd probably need
to stick it down to something heavier because they look pretty light.
Dave AB7E
On 9/17/2020 10:09 PM, Alan Bloom wrote:
I am currently "sheltering in place" far from home and would like to set
up a station here.
Hello all,
I am about to replace myself the 2 FETs in the amp, praying for no other
damages.
Not being experienced on the subject at all, can anyone elaborate please on
the procedure to properly adjust & align the amp before usage?
TIA & be safe
Isaac, 4Z1TL (4X2BESAFE)
--
This email has
16 matches
Mail list logo