Hello, I'm upgrading video machine from Fedora to Ubuntu 9.10(Ubuntu Karmic). I read from http://www.vislab.uq.edu.au/research/accessgrid/software/debian/karmic.html that AG3.2 beta is practically "stable".
On this video machine, I have 2 Hauppauge capture video cards based on BT878 Chipset. I made a dmsg command and I put on bold font the messages that I consider important. dmesg |grep bttv [ 8.393690] bttv: driver version 0.9.18 loaded [ 8.393697] bttv: using 8 buffers with 2080k (520 pages) each for capture [ 8.393945] bttv: Bt8xx card found (0). [ 8.393984] bttv 0000:03:02.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 8.394001] bttv0: Bt878 (rev 17) at 0000:03:02.0, irq: 21, latency: 32, mmio: 0xfe8ff000 [ 8.394218] bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb [ 8.394225] bttv0: using: Hauppauge (bt878) [card=10,autodetected] [ 8.394233] IRQ 21/bttv0: IRQF_DISABLED is not guaranteed on shared IRQs [ 8.394281] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init] [ 8.396775] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] [ 8.427649] bttv0: Hauppauge eeprom indicates model#44371 [ 8.427652] bttv0: tuner type=2 [ 8.819648] bttv0: registered device video0 [ 8.819707] bttv0: registered device vbi0 [ 8.819760] bttv0: registered device radio0 [ 8.828477] bttv0: PLL: 28636363 => 35468950 .. ok [ 8.860772] bttv: Bt8xx card found (1). [ 8.860804] bttv 0000:03:03.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 8.860817] bttv1: Bt878 (rev 17) at 0000:03:03.0, irq: 22, latency: 32, mmio: 0xfe8fd000 [ 8.876320] bttv1: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb [ 8.876328] bttv1: using: Hauppauge (bt878) [card=10,autodetected] [ 8.876334] IRQ 22/bttv1: IRQF_DISABLED is not guaranteed on shared IRQs [ 8.876382] bttv1: gpio: en=00000000, out=00000000 in=00ffffdb [init] [ 8.878868] bttv1: Hauppauge/Voodoo msp34xx: reset line init [5] [ 8.913092] bttv1: Hauppauge eeprom indicates model#44371 [ 8.913096] bttv1: tuner type=2 [ 8.929470] bttv1: registered device video1 [ 8.929525] bttv1: registered device vbi1 [ 8.929580] bttv1: registered device radio1 [ 8.938469] bttv1: PLL: 28636363 => 35468950 .. ok lspci command: 03:02.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 03:02.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) 03:03.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 03:03.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) 03:0e.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) I installed AG3.2 toolkit from uqvislab repository. Then, I have a problem. AG3.2 can not identify my /dev/video0 and /dev/video1, the Access Grid Node Management just can identify X11 like video source, but my ubuntu could identify my 2 video capture cards. My Ubuntu is: Linux video 2.6.31-14-generic #48-Ubuntu SMP Fri Oct 16 14:04:26 UTC 2009 i686 GNU/Linux Over a Poweredge 700 32 bits, Dell. Any ideas? Thanks in advance Porfirio Gaona UNAM - Mexico
