Hi All Just to clarify. I'm using a SONY HDR-SR12E camera. I've tested it both in PAL and NTSC formats at 1080i and its all fine. In resting phase. (very little activity) I'm getting 1.8M/s transfer rate. Mike
Quoting Nathan Gardiner <[email protected]>: > We have had problems trying to get an AVCHD camcorder to work with > BlackMagic card and i think most AVCHD camcorders that I tested didn't > seem to have true HDMI realtime output. > > I don't think that NTSC and PAL should make much difference as the > BlackMagic card accepts input from either or. > > Also, we should have a new JVC camcorder arriving in the next day or > so and will be testing that out. > > > Regards, > Nathan > > > > On 18/02/2009, at 11:56 AM, Jimmy Miklavcic wrote: > >> I did check it a while back and it was fine. I had to install a >> graphics card in order for Media Express to work. Right now I'm >> using the on-board VGA for the display. I didn't think I needed a >> high-end display card just to run the service manager. Anyway I >> think you and I are seeing the same symptoms. I'm using 720 @ 30p. >> >> Jimmy >> >> -- >> Jimmy Miklavcic >> Multimedia Specialist >> [email protected] >> >> UNIVERSITY OF UTAH >> CTR FOR HIGH PERFORM COMPUTING >> 155 SOUTH 1452 EAST RM 405 >> SALT LAKE CITY, UT 84112-0190 >> >> Office: 801.585.9335 >> Fax: 801.585.5366 >> >> http://www.anotherlanguage.org >> >> >> From: [email protected] [mailto:[email protected]] On >> Behalf Of Andrew Ford >> Sent: Tuesday, February 17, 2009 2:43 PM >> To: Jimmy Miklavcic >> Cc: [email protected]; Nathan Gardiner; ag- [email protected] >> Subject: Re: [AG-TECH] BlackMagic HDMI vic beta download >> >> Hi Jimmy, >> >> Did you try checking the HDMI input directly, via either Blackmagic >> Media Express or AMCap? If that works then we probably have the >> same problem - I can see the video fine in Media Express but vic >> just shows a black screen with any codec or size. Here we have the >> Blackmagic Intensity Pro cards with Sony HDR-SR11 cameras, which >> are AVCHD. Side note: I don't think the recording format makes >> much of a difference, just the specific video format, as in 1080i >> at a certain framerate. >> >> Nathan, is vic expecting a certain framerate? The format that >> worked with Media Express was 1080i @ 59.97. If it's only been >> tested with PAL so far, I would hazard a guess and say that the >> NTSC isn't using the right format/framerate in some way. >> >> --Andrew >> >> 2009/2/17 Jimmy Miklavcic <[email protected]> >> >> Mike, it's great news that you have been able to get HIT Lab's vic to >> work. I haven't been so lucky. I have AVCHD (Panasonic AG-HMC150) video >> cameras. Mike I think that you have MPEG2 based HD cameras. Are yours >> Sony? Nathan, I don't think you tested with an AVCHD camera. >> >> All I get is black, which I think tells me that it sees the video card >> but not, the video stream. Mike, did you use 1080i/p or 720p? >> >> If anyone has any suggestions, I'm open. >> >> Jimmy >> >> >> -- >> Jimmy Miklavcic >> Multimedia Specialist >> [email protected] >> >> UNIVERSITY OF UTAH >> CTR FOR HIGH PERFORM COMPUTING >> 155 SOUTH 1452 EAST RM 405 >> SALT LAKE CITY, UT 84112-0190 >> >> Office: 801.585.9335 >> Fax: 801.585.5366 >> >> http://www.anotherlanguage.org >> >> >> -----Original Message----- >> From: [email protected] >> [mailto:[email protected]] On Behalf Of >> [email protected] >> Sent: Tuesday, February 17, 2009 1:52 AM >> To: Nathan Gardiner >> Cc: [email protected]; [email protected] >> Subject: Re: [AG-TECH] BlackMagic HDMI vic beta download >> >> Hi Nathan >> Thanks otherwise all looking good. >> Not bad on bandwidth usage either. >> Mike >> >> Michael Daley M.Phil MBCS GCFA ---------------------------------------------------------------- This message was sent using IMP, the Internet Messaging Program.
